Saxby Lighting Halbury Wall Manual

Instruction leaflet
Halbury Wall
54553, 54554
www.saxbylighting.com Saxby Lighting Ltd. LS9 0SE
Iss.2 15072015

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
This product is Class 2 (Double insulated)
and must not be earthed.
Please read these instructions carefully before
commencing any work.
This unit should be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without
your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a circuit with a
30mA RCD fitted.
If replacing an existing fitting, make a careful note of the
connections.
This product contains non-replaceable parts and cannot
be serviced. If damage occurs the part should be
scrapped.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
This product is rated at IP44.
The diffuser (cover) can become hot in use. Switch off
and allow 10 minutes to cool before cleaning, replacing
or adjusting.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 60W E27 GLS
IP rating: 44
Layout
• Planthedesiredlayoutofthisfittingcarefully,ensuring
the cables will reach the distance between the junction
box and the light fitting.
• Avoidlocatinganycablesinpositionsthatwouldcause
a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may
be at risk from being cut, trapped or damaged.
• WerecommendthatyouuseH05RN-Fspecification
cable (not supplied) which is an outdoor grade, rubber
sheathed cable. The mains supply cable must have a
minimum cross sectional area of 1.0mm²
• Cablesmustbeprotectedusingsuitableconduitor
plastic trunking.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
• Thehelpofanassistantisrecommendedwhen
installing this fitting.
• Remove6securingscrewstoseparateshadefromwall
back. PIR sensor connection cable can be disconnected
tomakeinstallationeasier(seeFig.1).
• Usingthewallbackasatemplate,marktheposition
of the mounting holes. Drill holes and fit supplied wall
plugs (suitable for masonry only - for other surfaces use
appropriatefixings).Feedtheincomingmainssupply
cablethroughthegrommetentryhole.Fixthewallback
tothewallusingthesuppliedscrews(SeeFig.2).
• Wireasdetailedbelow.
Installation
Fig. 2
Fig. 1
Wiring
This product is double insulated and must not be earthed.
If there are any incoming earth cables, they must be joined
together and well insulated with good quality insulation tape.
This is to ensure earth continuity throughout your property.
Remove the cover from the mains terminals and having
correctly identified the wiring from your existing light
fitting,connect to the quick fit connection block in the
following way:
ive
eutra l

• Refittheshade.ReconnectPIRsensorcableifnecessary.
• Replacefuseorcircuitbreakerandswitchon.Yourlight
is now ready for use.
Commissioning
PIR Adjustment
• Whenchangingabulb,alwaysswitchoffatthemains
and allow the bulb to cool before handling.
•Alwaysusethecorrecttypeandwattagebulb.Usingthe
incorrect wattage bulb will damage the bulb and ballast.
•Usedbulbsshouldnotbedisposedofwithhousehold
waste. Please recycle where facilities exist.
•Unscrewthebulbanticlockwisetoremove.
•Insertthebulbgentlyintothefitting.Screwclockwiseinto
the lampholder.
Fitting/replacing bulbs
Live Voltages may be present in this unit even when turned off or when completely disconnected.Foryoursafety,
always switch off the supply before changing lightbulbs, or cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
1. The unit must be installed in a vertical position, and fitted
1.8m - 2.5m above the ground.
2.ThePIRsensorcanbeadjustedusingtheLUXandTIME
screws, allowing the detection distance to be altered
to suit the location. The detection angle is set at 130
degrees and the maximum detection distance is 12m.
The PIR will start activating when the light level drops
to 5 LUX and will continue to activate until the light
levelrisesto2000 LUX.Whenadjustingthesensitivity
(detection distance) in daylight it will be necessary to
cover the sensor to simulate night time. When the PIR
is activated the light will remain lit for a maximum of 5
minutes. The minimum is 5 seconds.
40W E27 GLS
This light source is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.