Saxby Lighting Ware Outdoor Wall Manual

V3 10/12/2019
Instruction leaflet
Ware Outdoor Wall
EL-40088
www.saxbylighting.com Saxby Lighting Ltd. BH17 7BY
Commissioning
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
This light source is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
(6) and secure the lamp holder plate (4) with the 2 x
screws removed in 3 above – being careful not to trap or
damage internal cables.
Diagram C. Place the bracket over the pre-drilled holes
in the mounting surface, and secure using the screws /
wall plugs provided.
is now ready for use.
Safety information
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
damp cloth. Do not use abrasive materials as these will
damage the finish.
and allow the bulb to cool before handling.
incorrect wattage bulb will damage the bulb and ballast.
waste. Please recycle where facilities exist.
into the lampholder.
Fitting/replacing bulbs
40W E27 GLS
Diagram C. Shade shape may vary from that shown.
Replace Cracked Shade
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.

NEUTRAL
SWITCHED LIVE
BLUE (N)
BROWN (L)
SUPPLY LIGHT FITTING
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
Specification
Voltage: 240V 50Hz a.c.
Lamp: 40W E27 GLS
IP rating: 44
Layout
Installation
Wiring
Existing fittings must be completely removed before
installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
account the exit position of the cable. Ensure that the
mounting surface is solid, preferably a brick or block
wall and ensure that there are no other cables or pipes
Diagram A.
and mark and drill the (four) mounting holes (3) – but do
not fix to the surface yet.
Diagram B.
housing plate (4) and remove it from the fitting. This
will enable you to access the internal terminal block (5).
Wire as detailed below.
box and the light fitting.
boxes (not supplied) away from areas where they may
be at risk from being cut, trapped or damaged.
cable which is an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross
sectional area of 1.0mm²
plastic trunking.
This light fitting is Double Insulated and
does not require connection to an Earth
circuit.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without your
knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the
connections.
Always use the correct type and wattage bulb. Exceeding
the bulb wattage will damage the product.
When changing a bulb, always switch off at the mains and
allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly.
This product is suitable for dimming when used in
verification of dimming abilities with the lamp
manufacture prior to use.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
Having correctly identified the wiring from your light fitting, connect to the approved outdoor rated external terminal block in
the following way:
Diagram A. Shade shape may vary from that shown. Diagram B. Shade shape may vary from that shown.
Check that...
The connections are tight
block.