SCAN 47-2 User manual

SCAN 47-2
INSTRUCTIONS FOR
INSTALLATION AND USE
This manual is accompanied by a
pamphlet with General Instructions
for Installation. Edition 09.05 - GB
MONTERINGSVEJLEDNING
med brugs- og fyringsanvisning
Indhold:
Generelle råd og anvisninger . . . . . . . . . .2-3
Reklamationsret
Type- og miljøgodkendelse
Udpakning
Tilbehør til din pejs
Montering af kakler og fedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærende underlag
Brændbar eller ikke brændbar væg
Gulvplade
Varmefordeling
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning. . . . . . . . . . . . . . . . .4-7
Tilslutning til eksisterende/muret skorsten
Tilslutning topafgang til stålskorsten
Forbrændingsluft udefra
Brugs- og fyringsanvisning . . . . . . . . . . . 8-10
Vedligeholdelse af pejseovnen
Håndtering af brændsel
Optænding og fyring
Fejlsøgning . . . . . . . . . . . . . . . . . . . . . . . . 11
SCAN 3
BRUGSANVISNING
TildenneBrugsanvisninghørerogsåen
generelMonteringsvejledning.Udgave03.03-DK
MONTERINGSVEJLEDNING
medbrug
s-ogfyringsanvisning
Indhold:
Generellerådoganvisninger..........2-3
Reklamationsret
Type-ogmiljøgodkendelse
Udpakning
Tilbehørtildinpejs
Monteringafkaklerogfedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærendeunderlag
Brændbarellerikkebrændbarvæg
Gulvplade
Varmefordeling
Selvlukkendelåge
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning.................4-7
Tilslutningtileksisterende/muretskorsten
Tilslutningtopafgangtilstålskorsten
Forbrændingsluftudefra
Brugs-ogfyringsanvisning...........8-10
Vedligeholdelseafpejseovnen
Håndteringafbrændsel
Optændingogfyring
Fejlsøgning........................11
Tildennemonteringsvejledninghørerogsåen
separatbrugsanvisningfordenenkeltepejs.
Udgave02/03-DK
Til dennemonteringsvejledning hørerogsåen
separatbrugsanvisning fordenenkelte pejs.
Udgave 02/03 - DK
Approved according to EN 13240

Clean combustion
The SCAN 47-2 uses the "CB technique"
(Clean-Burn) to ensure an optimally clean
combustion. The extra combustion air is pre-
heated and led into the combustion chamber
close to the ceramic smoke deflector. Ceramic smoke deflectors
Lift up the lower ceramic smoke deflector, pull out
the pins in the lateral combustion chamber plates
and remove the deflector. The upper deflector is
removed in the same way.
You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We are convinced
that your stove will be to your full satisfaction and give you many hours of pleasure if you follow the advice and
instructions of this manual.
Please read this manual as well as the General Instructions for Installation before beginning the installation.
Congratulations on your new SCAN stove!
5
3
1
4
1 Ashtray. When you open the lower door, you have
access to the ashtray, which is placed below the com-
bustion chamber. Attention! Be careful when you empty
ashes from the stove. There may be embers left for up
to 24 hours after the stove was last used.
2 Lid for ashtray. Under the ashtray you will find a lid
to put on top of the ashtray when you carry it out for
emptying.
3 Handle for shaking grate. The stove is equipped with
a shaking grate. When you activate the grate handle,
the ashes from the combustion chamber are emptied
into the ashtray.
4 Regulation for primary air. Turn the air valve in order
to open. The primary air is used when lighting and
refuelling the stove. It should always be closed during
continuous firing.
5 Regulation for combustion air. Push the button side-
ways. Left position is closed and right position is open.
The air is used for combustion and regulates the output
of the stove.
The ashtray, shaking grate, and primary air should always
be closed during continuous firing.
2
SCAN 47-2

Adjustment of the handle
The handle can be loosened and adjusted at the
lower closing hook with a hexagon spanner.
Accessories
For this model you can have the following accessories:
Handle
Pull out the handle to open.
Adjustment screws
The stove has two adjustment screws on the bottom
that can be used for levelling the stove.
Self-closing door (BA 1)
The door is prepared with a self-closing function at the
factory. If you tighten the spring with the hexagon spanner,
the door will close automatically when you let go of it.
• Shaped floor plate in steel or glass
• Connection piece for fresh-air intake
You should read this manual as well as the General Instructions for Installation before beginning the installation.
SCAN 47-2
The stove can be prepared for an external air supply where
fresh air is let directly into the combustion chamber (can
also be done subsequently by the authorized dealer).
Data for calculation of the chimney and adjustment of the air according to EN 13240:
Combustion
air
%
Primary air
%
Max. fuel
kg
Chimney
draught, min.
Pa.
Flue outlet
flow
g/s
Temperature of
flue outlet
behind flue collar
oC
Rated output
kW
Fuel consump-
tion
kg/h
Efficiency
%
60 25 1.5 11 7.1 195 7.4 2 84

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
*
**
* To the middle of the rear outlet
** Connection piece to fresh air intake
Distances to flammable materials
(mm)
Production number
Write the production number of your
stove here so that you have it at hand
in case you need to contact us.
You can choose between several floor plates in
different shapes and dimensions for your stove.
Furthermore, you can have a specially made,
shaped floor plate for the SCAN 47-2, which is to
be placed in front of the stove (available in steel
or glass). Please contact your local authorities
concerning the security distances needed.
SCAN 47-2
300
Distance to furniture: 850 mm
150
150
150
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class mate-
rial and are subject to a strict quality control before they leave the factory.
However, if an error should occur, we back all SCAN wood-burning stoves
and inserts with an extensive, five-year limited warranty.
See also the General Instructions for Installation delivered with your stove
for more details.
Technical info
Rated output: 7.4 kW
Min./max.: 3 - 9 kW
Weight: 140 kg
Connection piece, diameter: int. 135 mm / ext. 148 mm