SCAN 60 User manual

SCAN 60
INSTRUCTIONS FOR
INSTALLATION AND USE
This manual is accompanied by a pamphlet with
General Instructions for Installation. Edition 09.06 - GB
MONTERINGSVEJLEDNING
med brugs- og fyringsanvisning
Indhold:
Generelle råd og anvisninger . . . . . . . . . .2-3
Reklamationsret
Type- og miljøgodkendelse
Udpakning
Tilbehør til din pejs
Montering af kakler og fedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærende underlag
Brændbar eller ikke brændbar væg
Gulvplade
Varmefordeling
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning. . . . . . . . . . . . . . . . .4-7
Tilslutning til eksisterende/muret skorsten
Tilslutning topafgang til stålskorsten
Forbrændingsluft udefra
Brugs- og fyringsanvisning . . . . . . . . . . . 8-10
Vedligeholdelse af pejseovnen
Håndtering af brændsel
Optænding og fyring
Fejlsøgning . . . . . . . . . . . . . . . . . . . . . . . . 11
SCAN 3
BRUGSANVISNING
TildenneBrugsanvisninghørerogsåen
generelMonteringsvejledning.Udgave03.03-DK
MONTERINGSVEJLEDNING
medbrug
s-ogfyringsanvisning
Indhold:
Generellerådoganvisninger..........2-3
Reklamationsret
Type-ogmiljøgodkendelse
Udpakning
Tilbehørtildinpejs
Monteringafkaklerogfedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærendeunderlag
Brændbarellerikkebrændbarvæg
Gulvplade
Varmefordeling
Selvlukkendelåge
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning.................4-7
Tilslutningtileksisterende/muretskorsten
Tilslutningtopafgangtilstålskorsten
Forbrændingsluftudefra
Brugs-ogfyringsanvisning...........8-10
Vedligeholdelseafpejseovnen
Håndteringafbrændsel
Optændingogfyring
Fejlsøgning........................11
Tildennemonteringsvejledninghørerogsåen
separatbrugsanvisningfordenenkeltepejs.
Udgave02/03-DK
Til dennemonteringsvejledning hørerogsåen
separatbrugsanvisning fordenenkelte pejs.
Udgave 02/03 - DK
Approuved according to EN 13240 2003
Declaration of Conformity
Manufacturer:
Krog Iversen & Co. A/S
DK - 5492 Vissenbjerg
Product:
SCAN 60
Description of product:
Room heater for closed operation
This product complies with the requirements
of the directive
CPD 89/106/EEC
Applied to harmonized standard EN 13240
Signature: _____________________________
Managing director Henning Krog Iversen

1Ashtray. The ashtray is placed below the combustion
chamber. Attention! Be careful when you empty ashes
from the stove. There may be embers left for up to 24
hours after the stove was last used.
2 Handle for shaking grate. The stove is equipped with a
shaking grate. When you activate the grate handle, the
ashes from the combustion chamber are emptied into the
ashtray.
3 Regulation for primary air. Push the button sideways.
Left position is closed and right position is open. The pri-
mary air is used when lighting and refuelling the stove. It
should always be closed during continuous firing.
4 Regulation for combustion air. Push the button side-
ways. Left position is closed and right position is open.
The air is used for combustion and regulates the output
of the stove.
Clean combustion
The SCAN 60 uses the "CB technique" (Clean-Burn) to
ensure an optimally clean combustion. The extra combu-
stion air is preheated and led into the combustion chamber
close to the ceramic smoke deflector.
Ceramic smoke deflectors
Lift up the lower ceramic smoke deflector, pull out the
pins in the lateral combustion chamber plates and
remove the deflector. The upper deflector is removed in
the same way.
You have chosen a product from one of Europe's leading
manufacturers of wood-burning stoves. We are convinced
that your stove will be to your full satisfaction and give you
many hours of pleasure if you follow the advice and instruc-
tions of this manual.
Please read this manual as well as the General Instructions
for Installation before beginning the installation.
Congratulations on your new SCAN stove!
2
4
3
1
SCAN 60
The ashtray, shaking grate, and primary air should always
be closed during continuous firing.

Accessories
For this model you can have the follo-
wing accessories:
Handle
Pull out the handle to open.
Adjustment screws
The stove has two adjustment screws on the bot-
tom that can be used for levelling the stove.
Self-closing door (BA1)
The door is prepared with a self-closing function at the
factory. If you tighten the spring with the hexagon spanner,
the door will close automatically when you let go of it.
• Large grill
• Connection piece for fresh-air
intake
SCAN 60
You should read this manual as well as the General Instructions for Installation before beginning the installation.
Connecting piece
The connecting piece is prepared for top outlet at
the factory. Proceed as follows for rear outlet:
Remove the steel top plate from the stove.
Dismount the connecting piece by unscrewing
the two wing screws. Remove both screws in the
rear plate of the stove. Cut free the pre-punched
plate with a pair of nippers. Turn the connecting
piece around and tighten it with the wing screws.
Connect the pipe to the chimney and put the steel
top plate back on the stove.
The stove can be prepared for an exter-
nal air supply where fresh air is let direct-
ly into the combustion chamber (can also
be done subsequently by the authorized
dealer).
Combustion air % Primary air % Max. fuel, kg Fuel consumption, kg/h
75 75 2 2,1
Adjustment of the air + fuel consumption (EN 13240):

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
600
880
447
124
790
137
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-
class material and are subject to a strict quality control before
they leave the factory. However, if an error should occur, we
back all SCAN wood-burning stoves and inserts with an exten-
sive, five-year limited warranty.
See also the General Instructions for Installation delivered
with your stove for more details.
**
* To the middle of the rear outlet
** Connection piece to fresh-air intake
Distances to flammable materials (mm)
Production number
Write the production number of your
stove here so that you have it at hand in
case you need to contact us.
You can choose between several floor plates in different
shapes and dimensions for your stove. Please contact your
local authorities concerning the security distances needed.
SCAN 60
*
Radiation area
Distance to furniture: 800 mm
180
180
300
180
Technical info
Emission (% CO at 13% O2): 0.07%
Efficiency: 78%
Rated output: 7 kW
Chimney temperature: 262 oC
Flue outlet flow: 8,1 g/sec
Recommended low pressure in conn. piece: 15 Pa
Recommended fuel: Wood
Amount of fuel: 2,0 kg
Min./max. (information from the factory): 2-8 kW
Weight: 132 kg
Connection piece, int. diameter: 135 mm
Connection piece, ext. diameter: 148 mm