SCAN Andersen 10 User manual

SCAN
Andersen 10
This manual is accompanied by a pamphlet
with General Instructions for Installation. Edition 09.06 - GB
MONTERINGSVEJLEDNING
med brugs- og fyringsanvisning
Indhold:
Generelle råd og anvisninger . . . . . . . . . .2-3
Reklamationsret
Type- og miljøgodkendelse
Udpakning
Tilbehør til din pejs
Montering af kakler og fedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærende underlag
Brændbar eller ikke brændbar væg
Gulvplade
Varmefordeling
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning. . . . . . . . . . . . . . . . .4-7
Tilslutning til eksisterende/muret skorsten
Tilslutning topafgang til stålskorsten
Forbrændingsluft udefra
Brugs- og fyringsanvisning . . . . . . . . . . . 8-10
Vedligeholdelse af pejseovnen
Håndtering af brændsel
Optænding og fyring
Fejlsøgning . . . . . . . . . . . . . . . . . . . . . . . . 11
SCAN 3
BRUGSANVISNING
TildenneBrugsanvisninghørerogsåen
generelMonteringsvejledning.Udgave03.03-DK
MONTERINGSVEJLEDNING
medbrug
s-ogfyringsanvisning
Indhold:
Generellerådoganvisninger..........2-3
Reklamationsret
Type-ogmiljøgodkendelse
Udpakning
Tilbehørtildinpejs
Monteringafkaklerogfedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærendeunderlag
Brændbarellerikkebrændbarvæg
Gulvplade
Varmefordeling
Selvlukkendelåge
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning.................4-7
Tilslutningtileksisterende/muretskorsten
Tilslutningtopafgangtilstålskorsten
Forbrændingsluftudefra
Brugs-ogfyringsanvisning...........8-10
Vedligeholdelseafpejseovnen
Håndteringafbrændsel
Optændingogfyring
Fejlsøgning........................11
Tildennemonteringsvejledninghørerogsåen
separatbrugsanvisningfordenenkeltepejs.
Udgave02/03-DK
Til dennemonteringsvejledning hørerogsåen
separatbrugsanvisning fordenenkelte pejs.
Udgave 02/03 - DK
INSTRUCTIONS FOR
INSTALLATION AND USE
Approved according to EN 13240 2003
Declaration of Conformity
Manufacturer:
Krog Iversen & Co. A/S
DK - 5492 Vissenbjerg
Product:
SCAN ANDERSEN 10
Description of product:
Room heater for closed operation
This product complies with the requirements
of the directive
CPD 89/106/EEC
Applied to harmonized standard EN 13240
Signature: _____________________________
Managing director Henning Krog Iversen

You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We are convinced that
your stove will be to your full satisfaction and give you many hours of pleasure if you follow the advice and instructions of
this manual.
Please read this manual as well as the General Instructions for Installation before beginning the installation.
Congratulations on your new SCAN stove!
Ceramic smoke deflectors
1 Ashtray. When you open the door, you have access to
the ashtray, which is placed below the combustion cham-
ber. Attention! Be careful when you empty ashes from the
stove. There may be embers left for up to 24 hours after
the stove was last used.
2 Handle for shaking grate. The stove is equipped with a
shaking grate. When you activate the grate handle, the
ashes from the combustion chamber are emptied into the
ashtray.
3 Regulation for primary air. Pull out the handle in order
to open. The primary air is used when lighting and
refuelling the stove. It should always be closed during
continuous firing.
Air for lighting of the stove. Tilt down and pull out the
handle for extra air when lighting the stove and when
refuelling. It should always be closed during conti-
nuous firing.
Clean combustion
The SCAN Andersen 10 uses the "CB technique"
(Clean-Burn) to ensure an optimally clean combu-
stion. The extra combustion air is preheated and led
into the combustion chamber close to the ceramic
smoke deflector.
Ceramic smoke deflectors
Lift up the lower ceramic smoke deflector, pull out the
pins in the lateral combustion chamber plates and
remove the deflector. The upper deflector is removed
in the same way.
SCAN Andersen 10
1
3
2
3a
3a
The shaking grate and primary air should always be clo-
sed during continuous firing.

Handle
Pull out the handle to open the door.
Mounting of the soapstones
Place the soapstone sides at the sides of the stove.
Push the enclosed bolt through the soapstone sides
from the outside and fasten.
SCAN Andersen 10
You should read this manual as well as the General Instructions for Installation before beginning the installation.
Regulation for combustion air. Push the button sideways. Left
position is closed and right position is open. The air is used for the
combustion and regulates the output of the stove.
Combustion air % Primary air % Max. fuel, kg Fuel consumption, kg/h
75 75 1,96 1,7
Adjustment of the air + fuel consumption (EN 13240):

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
Technical info
Emission (% CO at 13% O2): 0.07%
Efficiency: 79%
Rated output: 7 kW
Chimney temperature: 229 oC
Flue outlet flow: 7,7 g/sec
Recommended low pressure in conn. piece: 15 Pa
Recommended fuel: Wood
Amount of fuel: 1,96 kg
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class material and are subject to a strict quality control before they
leave the factory. However, if an error should occur, we back all SCAN wood-burning stoves and inserts with an extensive, five-
year limited warranty.
See also the General Instructions for Installation delivered with your stove for more details.
* To the middle of the rear outlet
Distances to flammable
materials (mm)
SCAN Andersen 10
You can choose between several floor plates in different
shapes and dimensions for your stove. Please contact
your local authorities concerning the security distances
needed.
889
676
172
404
774
*
A: 300 mm
B: 150 mm
Distance to furniture: 800 mm
B
B
B
A
Min./max. (information from the factory): 3-11 kW
Weight, stove with convection: 140 kg
Weight, stove with soap stone: 246 kg
Connection piece, int. diameter: 135 mm