SCAN 55 User manual

SCAN 55
This manual is accompanied by a pamphlet
with General Instructions for Installation. Edition 03.06 - GB - 02
MONTERINGSVEJLEDNING
med brugs- og fyringsanvisning
Indhold:
Generelle råd og anvisninger . . . . . . . . . .2-3
Reklamationsret
Type- og miljøgodkendelse
Udpakning
Tilbehør til din pejs
Montering af kakler og fedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærende underlag
Brændbar eller ikke brændbar væg
Gulvplade
Varmefordeling
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning. . . . . . . . . . . . . . . . .4-7
Tilslutning til eksisterende/muret skorsten
Tilslutning topafgang til stålskorsten
Forbrændingsluft udefra
Brugs- og fyringsanvisning . . . . . . . . . . . 8-10
Vedligeholdelse af pejseovnen
Håndtering af brændsel
Optænding og fyring
Fejlsøgning . . . . . . . . . . . . . . . . . . . . . . . . 11
SCAN 3
BRUGSANVISNING
TildenneBrugsanvisninghørerogsåen
generelMonteringsvejledning.Udgave03.03-DK
MONTERINGSVEJLEDNING
medbrug
s-ogfyringsanvisning
Indhold:
Generellerådoganvisninger..........2-3
Reklamationsret
Type-ogmiljøgodkendelse
Udpakning
Tilbehørtildinpejs
Monteringafkaklerogfedtsten
Kvalitetskontrol
Anmeldelsespligt
Skorstenstjek
Skorstensløsninger
Bærendeunderlag
Brændbarellerikkebrændbarvæg
Gulvplade
Varmefordeling
Selvlukkendelåge
Justerskrue
Typeskilt
Produktionsnr.
Servicepakke
Monteringsvejledning.................4-7
Tilslutningtileksisterende/muretskorsten
Tilslutningtopafgangtilstålskorsten
Forbrændingsluftudefra
Brugs-ogfyringsanvisning...........8-10
Vedligeholdelseafpejseovnen
Håndteringafbrændsel
Optændingogfyring
Fejlsøgning........................11
Tildennemonteringsvejledninghørerogsåen
separatbrugsanvisningfordenenkeltepejs.
Udgave02/03-DK
Til dennemonteringsvejledning hørerogsåen
separatbrugsanvisning fordenenkelte pejs.
Udgave 02/03 - DK
EN 13240 2003
INSTRUCTIONS FOR
INSTALLATION AND USE

You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We are convinced that your
stove will be to your full satisfaction and give you many hours of pleasure if you follow the advice and instructions of this
manual.
Please read this manual as well as the General Instructions for Installation before beginning the installation.
Congratulations on your new SCAN stove!
Ceramic smoke deflectors
1 Ashtray. When you open the door in front of the wood
compartment, you have access to the ashtray, which is
placed below the combustion chamber. Attention! Be
careful when you empty ashes from the stove. There may
be embers left for up to 24 hours after the stove was last
used.
2 Handle for shaking grate. The stove is equipped with a
shaking grate. When you activate the grate handle, the
ashes from the combustion chamber are emptied into the
ashtray.
3 Regulation for primary air. Push the air control rod side-
ways. Left position is closed and right position is open. The
primary air is used when lighting and refuelling the stove.
It should always be closed during continuous firing.
The ashtray, shaking grate, and primary air should always
be closed during continuous firing.
Clean combustion
The SCAN 55 uses the "CB technique" (Clean-Burn) to
ensure an optimally clean combustion. The extra com-
bustion air is preheated and led into the combustion
chamber close to the ceramic smoke deflector.
Ceramic smoke deflectors
Lift up the lower ceramic smoke deflector, pull out the
pins in the lateral combustion chamber plates and
remove the deflector. The upper deflector is removed
in the same way.
SCAN 55
1
3
2
Adjustment of the air + fuel consumption (EN 13240):
Combustion air % Primary air % Max. fuel, kg Fuel consumption, kg/h
75 75 2 2,02

A
Mounting of the lateral soap stones
Place the lateral soap stones on the pins (A). Put the pin on
the top of the stove into the soap stone and tighten the fitting.
You should read this manual as well as the General Instructions for Installation before beginning the installation.
Regulation for combustion air. Push the air control
rod sideways. Left position is closed and right position is
open. The air is used for combustion and re-gulates the
output of the stove.
Adjustment screws
The stove has two adjustment screws on the bottom that can
be used for levelling the stove.
When using a shaped floor plate, the stove must be adjusted
upwards to allow the plate to be pushed under the front of the
stove.
Write the production number of your
stove here so that you have it at hand
in case you need to contact us.
Production number
SCAN 55
Accessories
For this model you can have the following accessories:
• Lateral covering in soapstone
• Top plate in soapstone
• Steel floor plate
• Shaped floor plate in steel or glass
• Connection piece for fresh-air intake

Distance to furniture: 800 mm
Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
Technical info
Emission (% CO at 13% O2): 0.1%
Efficiency: 71%
Rated output: 6 kW
Chimney temperature: 334 oC
Flue outlet flow: 7.1 g/sec
Recommended low pressure in conn. piece: 18 Pa
Recommended fuel: Wood
Amount of fuel: 2,1 kg
Min./max. (information from the factory): 3-9 kW
Weight, stove with convection: 136 kg
Weight, stove with soap stone: 240 kg
Connection piece, int. diameter: 135 mm
Connection piece, ext. diameter: 148 mm
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class
material and are subject to a strict quality control before they leave
the factory. However, if an error should occur, we back all SCAN
wood-burning stoves and inserts with an extensive, five-year limited
warranty.
See also the General Instructions for Installation delivered with your
stove for more details.
* To the middle of the rear outlet
** Height to the beginning of the flue pipe at top outlet
***Connection piece to fresh-air intake
Distance to flammable materials
(mm):
You can choose between sev-
eral floor plates in different
shapesanddimensionsforyour
stove. Furthermore, you can
have a specially made, shaped
floor plate for the SCAN 55,
which is to be placed in front of
the stove. Please contact your
local authorities concerning the
security distances needed.
1028
500 414
177
150
849
966
175
175
609
*
**
***
175
450
Declaration of Conformity
Manufacturer:
Krog Iversen & Co. A/S
DK - 5492 Vissenbjerg
Product:
SCAN 55
Description of product:
Room heater for closed operation
This product complies with the requirements
of the directive
CPD 89/106/EEC
Applied to harmonized standard EN 13240
Signature: _____________________________
Managing director Henning Krog Iversen
SCAN 55