SCAN 29 User manual

SCAN 29
INSTRUCTIONS FOR
INSTALLATION AND USE
This manual is accompanied by a pam-
phlet with General Instructions for
Installation. Edition 07.03 - GB
Approved according to DIN 18891

You have chosen a product from one of Europe's leading
manufacturers of wood-burning stoves. We are convinced
that your stove will be to your full satisfaction and give you
many hours of pleasure if you follow the advice and instruc-
tions of this manual.
Please read this manual as well as the General
Instructions for Installation before beginning the instal-
lation.
Congratulations on your new SCAN stove!
1 Ashtray. When you open the cover under the door
you have access to the ashtray, which is placed
below the combustion chamber. Attention! Be care-
ful when you empty ashes from the stove. There
may be embers left for up to 24 hours after the stove
was last used.
2 Lid for ashtray. Under the ashtray you will find a lid
to put on top of the ashtray when you carry it out for
emptying.
3 Handle for shaking grate. The stove is equipped
with a shaking grate. When you activate the grate
handle, the ashes from the combustion chamber are
emptied into the ashtray.
4 Regulation for primary air. Turn the air valve in
order to open. The primary air is used when lighting
and refuelling the stove. It should always be closed
during continuous firing.
5 Regulation for combustion air. Push the button
sideways. Left position is closed and right position
is open. The air is used for combustion and regu-
lates the output of the stove.
The ashtray, shaking grate, and primary air should
always be closed during continuous firing.
Transport safety
Do not forget to remove the transport safety screw
on the rear of the stove before mounting the stove.
Cleaning of the glass
If you need to clean the glass, you should proceed as fol-
lows: The stove must be cold. Push the door about ¼ of
the way up. Close the door lock at the right (see below).
Use the special wrench to loosen the screws on both
sides of the door (a). Pivot the door (b) and clean the
glass. After cleaning the glass, pivot the door back and
fasten the two screws. Open the door lock and close the
door.
Locking of the door
You can lock the door in the open position for refuelling of
wood. This is done by pulling the locking ring forwards
(see the arrow).
ab
2
1
4
5
3
SCAN 29
Wood / briquettes Fuel kg/h (beechwood
max. 20% humidity)
SCAN 29 2,4 kg
Combustion air % 75
Primary air % 0
Adjustment of the air

Ceramic smoke deflector
In order to dismount the ceramic smoke deflector, lift the
plate off the pins in the lateral combustion chamber plates
and take it down.
Accessories
For this model you can have the following accessories:
Handle
The door is opened by pulling up the handle.
Adjustment screws
The stove has two adjustment screws on the bottom that can
be used for levelling the stove.
• Lateral covering in soapstone or
ceramic tiles
• Top plate in soapstone or ceramic tile
• Baking-compartment door
• Small grill
• Swivel grill
• Steel floor plate
• Connection piece for fresh-air intake
Self-closing door (BA 1)
The stove can be delivered with a self-closing function
at the factory.
SCAN 29
Wires and wheels
Smooth operation of your wires and wheels requires
regular maintenance with a special grease purchased
through your local authorised dealer.
Data for calculation of the chimney
Stove
model
SCAN
Connecting
adaptor
mm
1
Density of
flue gas
flow
g/s
2
Flue gas
tempera-
ture
oC
3
Minimum
draft
Pa
4
Density of
flue gas
flow
g/s
5
Flue gas
temperature
oC
6
Minimum
draft
Pa
7
0,8
Minimum
draft
Pa
29 150 - - - 6 310 12 10
With closed doorsWith open doors
Column 2 and 5 show the flue gas temperature in the connecting adaptor
Column 3 and 6 show the lowest/minimum draft in Pa by rated value
Column 7 shows the lowest/minimum draft in Pa by 0.8 x rated value

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
153
500594
170 1021
1170
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class material
and are subject to a strict quality control before they leave the factory.
However, if an error should occur, we back all SCAN wood-burning stoves
and inserts with an extensive, five-year limited warranty.
See also the General Instructions for Installation delivered with your
stove for more details.
Technical info
Rated output: 7 kW
Min./max.: 3 - 9 kW
Weight: 155 - 300 kg
Connection piece, diameter: int. 135 mm / ext. 148 mm
*
**
* To the middle of the rear outlet
** Connection piece to fresh-air intake
Distances to flammable mate-
rials (mm)
Production number
Write the production number of your
stove here so that you have it at hand
in case you need to contact us.
www.ekermann.se • 001.2842
You can choose between several
floor plates in different shapes and
dimensions for your stove. Please
contact your local authorities con-
cerning the security distances nee-
ded.
SCAN 29
200
Base plate
Radiation area
500
800
800
200
You should read this manual as well as the General Instructions for Installation before beginning the installation.