SCAN 37-2 User manual

SCAN 37-2
INSTRUCTIONS FOR
INSTALLATION AND USE
This manual is accompanied by a
pamphlet with General Instructions for
Installation. Edition 10.04 - GB
Approved according to DIN 18891

Ceramic smoke deflectors
Lift up the lower ceramic smoke deflector, pull
out the pins in the lateral combustion chamber
plates and remove the deflector. The upper
deflector is removed in the same way.
You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We
are convinced that your stove will be to your full satisfaction and give you many hours of pleasure if
you follow the advice and instructions of this manual.
Please read this manual as well as the General Instructions for Installation before beginning the
installation.
Congratulations on your new SCAN stove!
S
C
A
N
1
4
5
2
1 Production number. Please always indicate the pro-
duction number in case you need to contact us.
2 Ashtray. When you open the door, you have access
to the ashtray, which is placed below the combustion
chamber. Attention! Be careful when you empty ashes
from the stove. There may be embers left for up to 24
hours after the stove was last used!
3 Lid for ashtray. Under the ashtray you will find a lid to
put on top of the ashtray when you carry it out for emp-
tying.
Handle for shaking grate. The stove is equipped with
a shaking grate. When you activate the grate handle,
the ashes from the combustion chamber are emptied
into the ashtray.
5 Regulation for primary air. Turn the air valve in order
to open. The primary air is used when lighting and
refuelling the stove. It should always be closed during
continuous firing.
3
Adjustment screws
The stove has two adjustment screws on the bottom
that can be used for levelling the stove.
SCAN 37-2
The ash tray, shaking grate, and primary air should
always be closed during continuous firing.
4
Clean combustion
The SCAN 37-2 uses the "CB technique"
(Clean-Burn) to ensure an optimally clean
combustion. The extra combustion air is pre-
heated and led into the combustion chamber
close to the ceramic smoke deflector.
Adjustment of the air Wood / briquettes Fuel kg/h (beechwood
max. 20% humidity)
SCAN 37-2 2 kg
Combustion air % 100
Primary air % 0

Regulation for combustion air
Push the button sideways. Left position is closed
and right position is open. The air is used for com-
bustion and regulates the output of the stove.
Accessories
For this model you can have the following accessories:
Adjustment of the handle
On the edge of the door, there is an adjustment
screw to adjust the vertical position of the hand-
le. The handle can be dismounted by removing
the hexagon screw on the inside of the door.
Handle
The door is opened by turning the handle
clockwise.
• Lateral covering in soap-
stone or stainless steel
• Soapstone top plate
• Soapstone for the bottom
• Stainless-steel front
• Shaped floor plate in black,
grey, stainless steel or glass
• Connection piece for fresh-
air intake
Self-closing door (BA 1)
The door is prepared with a self-closing function
at the factory. If you tighten the spring with the
hexagon spanner, the door will close automati-
cally when you let go of it.
SCAN 37-2

Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
175
518
527
1070
914
155
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class material and
are subject to a strict quality control before they leave the factory. However, if an
error should occur, we back all SCAN wood-burning stoves and inserts with an
extensive, five-year limited warranty.
See also the General Instructions for Installation delivered with your stove for
more details.
Technical info
Rated output: 7 kW
Min./max.: 3 - 9 kW
Weight: 125 - 160 kg
Connection piece, diameter: int. 135 mm / ext. 148 mm
Production number
*
**
*To the middle of the rear outlet
**Connection piece to fresh-air intake
Distances to flammable materials
(mm)
Write the production number of your
stove here so that you have it at hand
in case you need to contact us.
You can choose between several floor plates in different shapes
and dimensions for your stove. Furthermore, you can have a
specially made, shaped floor plate for the SCAN 37-2, which is
to be placed in front of the stove. Please contact your local aut-
horities concerning the security distances needed.
SCAN 37-2
200 500
300
800
800
Base plate
Radiation area
Data for calculation of the chimney
Stove
model
SCAN
Connecting
adaptor
mm
1
Density of
flue gas
flow
g/s
2
Flue gas
tempera-
ture
oC
3
Minimum
draft
Pa
4
Density of
flue gas
flow
g/s
5
Flue gas
temperature
oC
6
Minimum
draft
Pa
7
0,8
Minimum
draft
Pa
37-2 150 - - - 7 300 14 11
With closed doorsWith open doors
Column 2 and 5 show the flue gas temperature in the connecting adaptor
Column 3 and 6 show the lowest/minimum draft in Pa by rated value
Column 7 shows the lowest/minimum draft in Pa by 0.8 x rated value