Schlage MPC Cobra Series User manual

Installation Instructions
C
L
LEVER/
STRIKE
3 Di
3 Gi
4 Ji
4 Qi
1 Qi
15/16 DRILL FOR
#12-24
MACHINE
OR OR #12
WOOD
SCREWS
(2 PLACES)
5/32” DEEP
1 Qi ” DEEP
C
L
MPC COBRAMPC COBRA
MANUALLY PROGRAMMABLE CYLINDRICAL
LOCKING SYSTEM
DOOR, LATCH AND FRAME PREPARATION:
11
3 Gi
3 Ji
Ji
BACKSET*
C
L
DOOR EDGE
C
L
LOCK
C
L
LEVER/
STRIKE
DOOR MUST
CORRESPOND
WITH CENTER-
LINE OF
STRIKE
2 Qr
1 iQ
1 Gi
1” HOLE INTO
2 Qi“ HOLE
2 Qi“ THRU
19/32”THRU
(2 PLACES)
DRILL FOR #6-32 MACHINE
OR
#6 WOOD SCREWS
(2 PLACES)
DOOR PREP
FRAME PREP
LATCH PREP
*BACKSET = 2 Difor OLB
(MEASURED FROM = 2 Drfor SLB & ELB
CENTER OF BEVEL)
Use template or information below to prep
door, latch and frame.
PROGRAMMING STEPS:
INSTALLING 7-PIN SMALL-FORMAT IC CORE FOR MANUAL KEY OVERRIDE:
3/16” DEEP
7
TO CHANGE
PROGRAMMING CODE
ENTER PROG. CODE
ENTER NEW
PROG.CODE
ENTER NEW
PROG.CODE AGAIN
*
*
*
*
33
TO ADD
TOGGLE CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
191*
*
*
*
33
TO ADD
FREEZE/LOCKOUT CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
115*
*
*
*
33
TO ADD
ONE TIME USE CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
113*
*
*
*
99
TO CHANGE RELOCK
TIME DELAY (DEFAULT 5 SEC.)
ENTER PROG. CODE
TO END
*
*
*
*
33
TO ADD
SUPERVISED CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
117*
*
*
*
33
TO ADD
PASS THRU CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
119*
*
*
*
TO ADD
NORMAL USE CODE
ENTER PROG. CODE
ENTER NEW CODE
TO ADD MORE
TO END
*
*
*
*
*
3
1
1
5
TO DELETE
CODES
ENTER PROG. CODE
ENTER CODE
TO DELETE MORE
TO END
*
*
*
*
*
5
PRESS 1 FOR 1
SEC. AND/OR 5
FOR 5 SEC. THE
TIMES WILL ADD.
Use the steps on this page to
program codes into the lock.
The “*” key is used like the
<ENTER> key is on a com-
puter. After pressing the “*”
key, wait for the red and
green LEDs to stop flashing
before proceeding to the next
step. If at any time the red
LED stays on while the green
LED flashes an error has
occurred. The flashing mes-
sage will repeat three times.
Count the number of flashes
and consult the error code
chart below.
FLASHES ERROR CODE DESCRIPTION
2Code too long 8 digits max.
3Memory full, must delete some `
codes
4Can not delete Programming code -
use Change steps.
5Second entry did not match first
(Programming Code)
6Invalid entry, start over. (Verify that
any codes entered prior to this error
do not operate the lock.)
7Code to be deleted does not exist.
8Duplicate code, code already exists.
A. HOLD LOCK IN HORIZONTAL
POSITION AS SHOWN AND PUSH
PLUG IN UNTIL PIN FALLS OUT.
REMOVE PLUG.
B. INSERT CYLINDER CON-
TROL KEY INTO CORE AND
TURN CLOCKWISE TO
RETRACT LOCKING PIN.
C. PUSH CYLINDER CORE
INTO LOCK - RESISTANCE
WILL BE NOTICEABLE.
TURN KEY COUNTER-
CLOCKWISE TO ENGAGE
LOCKING PIN.
D. REMOVE KEY.
LOCK IS NOW
OPERATIONAL.
OPERATION:
EITHER THE CYLINDER PLUG
OR THE IC CORE MUST BE
INSTALLED FOR THE LOCK
TO OPERATE. REMOVAL OF
THE CORE OR PLUG AUTO-
MATICALLY UNLOCKS THE
LOCK. IT IS RECOMMENDED
THAT AN IC CORE BE
INSTALLED IN CASE IT EVER
BECOMES NECESSARY TO
UNLOCK THE LOCK USING
MECHANICAL MEANS.
Form 57010 Rev. A 02-22-2002
The MPC Cobra is a battery-pow-
ered manually programmed access
control system. Up to 100 individual
codes can be programmed right at
the keypad. A red and green LED
on the keypad provide visual indica-
tion for programming and access
events. Mechanical key override is
possible when a 7-pin small-format
interchangeable core (not included)
is installed in place of the cylinder
plug, which comes standard. Either
the plug or the IC core must be
installed for the lock to operate. When the
cylinder is removed (using the cylinder con-
trol key) the lock will unlock. Manual key
override should only be necessary if the low
battery output indications have been ignored.
(See Battery Information on page 3). The
design allows for mounting on doors from 1-
1/2” to 2” thick. The retractor design allows
easy adjustment for door thickness by rota-
tion. A shim is available to mount the lock to
a 1-3/8” door. An exterior gasket (EG option)
is available for application to exterior sides of
doors.
Page 1 of 2Page 4 of 4
REMOVE TAPE
(IF PRESENT)

SEE PAGE 4 FOR INFORMATION REGARDING
THE USE OF MECHANICAL KEY OVERRIDE
AND INSTALLATION STEPS FOR 7-PINSMALL
FORMAT IC CORE.
Apply LoktiteTM 242 or
equivalent to threads
Dot must face
down.
Apply Exterior
Gasket (EG option)
to this surface if
required.
Screw retractor all the way in and
unscrew it the correct number of
turns according to door thickness:
Make sure latch
tabs engage the
retractor as shown:
Install latch guard.
Plug in wiring harness
Shim plate only required
for 1-3/8” doors
INSTALL STRIKE & STRIKE BOX:
22
INSTALL LATCH:
33 REVERSE LEVERS (IF REQUIRED):
77
SET RETRACTOR DEPTH:
44
INSTALL INSIDE BASEPLATE ASSEMBLY:
55
INSTALL CYLINDER (RECOMMENDED):
66
INSTALL OUTSIDE ESCUTCHEON/SPINDLE:
88
INSTALL INSIDE ESCUTCHEON/SPINDLE:
99
PROGRAM LOCK CODES:
1010
Code Functions:
The MPC Cobra is manually programmable to have up to 100 codes. The codes can have different functions as
described below. Several types of functions have factory default values which are operational as soon as the lock is
installed. It is highly recommended that the Programming Code be changed (this will delete all factory default codes)
and new codes be added. In addition, it is recommended that at least one Freeze/Lockout Code be added - in case
the batteries get completely drained. (See “Battery Information” on below.) All codes can be 3-8 digits in length
(except the Programming code which must be 5-8 digits.) Keep a log of all issued codes. Issue codes exclusively with
all odd or all even numbers - this practice will make it easier to spot duplicate codes, since each keypad button repre-
sents two numbers (for example, code 246 is identical to code 135.)
FUNCTION: FACTORY DEFAULT: DESCRIPTION:
PROGRAMMING
NORMAL
9 7 5 3 1
1 3 5 7 9
1 3 5 1 3 5
9 1 1 5
NONE
NONE
NONE
TOGGLE
ONE USE
SUPERVISED
PASSTHRU
FREEZE/LOCKOUT
The programming code puts the lock into a programming mode. It will
not unlock the lock. When a Programming code plus “**” is entered the
LEDs alternately flash several times indicating the lock is in a program-
ming mode. If more than 30 seconds pass in between programming
entries, the lock returns to a normal operational state.
Normal codes unlock the lock for the relock time delay. While the lock is
unlocked the green LED will flash. The LED will stop flashing and the
lock will relock.
Toggle codes unlock the lock indefinitely. When the same (or another)
toggle code is entered, the lock will immediately relock. When a toggle
code is entered, the green LED will flash once. The LED will stop flash-
ing and the lock will relock. .
Freeze/Lockout codes prevent other codes from working. The lock can
be locked or unlocked when one is entered. If it is locked, a Pass Thru
code will unlock it but all other codes will not. Only another Lockout code
will reverse the effect.
One Use codes unlock the lock for the relock time delay. They will only
work once and then are deleted from memory. They can used again if
they are programmed (added) into memory again.
Supervised codes require that two different supervised codes entered in
order to unlock the lock for the relock time delay.
Pass Thru codes will unlock the door for the relock time delay even if
the door is in the lockout mode.
BATTERY INFORMATION:
The MPC Cobra uses four, standard AA batter-
ies. The batteries should provide enough life
for approximately 80,000 lock/unlock cycles.
When the batteries are running out the lock
provides two different modes of low battery
indication: First, when a code is entered, the
red LED will flash twelve times before the lock
executes the command of the code. This is an
indication that it is time to replace the batteries.
The lock will go for about 500 cycles in this
condition. After it reaches a certain point the
lock will go into “Low Battery Lockout” mode. A
Freeze/Lockout code will need to be entered in
order gain access. If the batteries are not
changed, the lock will eventually not work and
manual key override (if installed) will need to
be used.
CLEARING MEMORY:
Clearing memory will delete all programmed codes and restore
factory default codes. If the memory ever needs to be erased fol-
low the steps below:
1. Remove the inside escutcheon. Remove one of the batteries.
2. Press any key.
3. Hold down the “*” key and reinstall the battery. Continue holding
the “*” key down. The red LED will flash a few times and then stay
on.
4. Release the “*” key.
5. Install the inside escutcheon.
Note: to return the lock to the factory default relock time delay, do
steps 1-4 twice in a row.
Page 2 of 2 Page 3 of 4