SEA COMPACT Series Original instructions

COMPACT
SUPER COMPACT
INSTALLATION MANUALS
AND SAFETY INFORMATION
web site: www.sea-usa.com
e-mail: [email protected]
REV 05 - 04/2018
67410796
International registered trademark n. 2.777.971
SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716

International registered trademark n. 2.777.971
IMPORTANT SAFETY INFORMATION
All the above described operations must be made exclusively by an authorized installer
Clean and grease parts in movement (wheels,
counter-connecting rod, release, etc.)
Check for corroded parts and replace if
necessary
Check if the screws and all mounting
hardwares are properly tighten
Annual
Annual
Annual
Check the conditions of wear and tear of the
devices in movement
Check the correct drain of the rainwater
Check the integrity of the connection cables
Annual
Annual
Annual
Inspect the track for any signs of cracking or
separation
Ensure that the gate moves freely
Annual
Annual
Check and confirm the proper operation of all
safety devices (photocells, edge sensors etc)
Check and confirm the operation of all
installed accessories
Check and confirm the operation of the
manual release
Annual
Annual
Annual
TURNING ON THE POWER
Check the battery conditions and be sure that
connections are free of corrosion
Verify the functionally of the battery backup,
or power failure option
BY MAIN POWER SOURCE TURNED OFF
Annual
TURNING OFF THE POWER
CCCC
GENERAL SAFETY PRECAUTIONS
The following precautions are an integral and essential part of the product and must be supplied to the user Read
them carefully as they contain important indications for the safe installation, use and maintenance.
1. These instruction must be kept and forwarded to all possible future users of the system.
2. This product must be used only for that which it has been expressly designed.
3. Any other use is to be considered improper and therefore dangerous.
4. The manufacturer cannot be held responsible for possible damage caused by improper, erroneous or
unreasonable use.
5. Avoid operating in the proximity of the hinges or moving mechanical parts.
6. Do not enter the path of the moving gate while in motion.
7. Do not obstruct the motion of the gate as this may cause a situation of danger.
8. Do not allow children to play or stay within the path of the moving gate.
9. Keep remote control or any other control devices out of the reach of children, in order to avoid possible involuntary
activation of the gate operator.
10. In case of break down or malfunctioning of the product, disconnect from the main power source.
Do not attempt to repair or intervene directly, contact only qualified personnel for repair.
11. Failure to comply with the above may create a situation of danger.
12. All cleaning, maintenance or repair work must be carried out by qualified personnel.
13. In order to guarantee that the system works efficiently and correctly it is important to have the manufacturer's
instructions on maintenance of the gate and operator carried out by qualified personnel.
14. In particular, regular checks are recommended in order to verify that the safety devices are operating correctly.
All installation, maintenance and repair work must be documented and made available to the user.
IMPORTANT SAFETY INSTRUCTIONS
WARNING – To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Never let children operate or play with gate controls. Keep the remote control away from children.
3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
4.Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object
activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to
adjust and retest the gate operator properly can increase the risk of injury or death.
5. Use the emergency release only when the gate is not moving
6. KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. Have a qualified service person make
repairs to gate hardware.
7. The entrance is for vehicles only. Pedestrians must use separate entrance.
8. Every gate operator installation MUST have secondary protection devices agains entrapments, such as edge
sensors and photo beams more in particulary in places where the risk of entrapments is more likely to occur
9. SAVE THESE INSTRUCTIONS
!
PERIODICAL MAINTENANCE

GENERAL SAFETY INFORMATION
An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the
installation, operation, and user maintenance of the appliance.
The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and
shall stress the importance of proper grounding.
The installation instructions shall inform the installer that permanent wiring is to be employed as required by local
codes, and instructions for conversion to permanent wiring shall be supplied.
Information shall be supplied with a gate operator for:
a) The required installation and adjustment of all devices and systems to effect the primary and secondary protection
against entrapment (where included with the operator).
b) The intended connections for all devices and systems to effect the primary and secondary protection against
entrapment. The information shall be supplied in the instruction manual, wiring diagrams, separate instructions, or the
equivalent.
Vehicular gate operators (or systems)
A vehicular gate operator shall be provided with the information in the instruction manual that defines the different
vehicular gate operator Class categories and give examples of each usage. The manual shall also indicate the use for
which the particular unit is intended as defined in Glossary, Section 3. The installation instructions for vehicular gate
operators shall include information on the Types of gate for which the gate operator is intended.
A gate operator shall be provided with the specific instructions describing all user adjustments required for proper
operation of the gate. Detailed instructions shall be provided regarding user adjustment of any clutch or pressure relief
adjustments provided. The instructions shall also indicate the need for periodic checking and adjustment by a qualified
technician of the control mechanism for force, speed, and sensitivity.
Instructions for the installation, adjustment, and wiring of external controls and devices serving as required protection
against entrapment shall be provided with the operator when such controls are shipped with the operator.
Instructions regarding intended installation of the gate operator shall be supplied as part of the installation instructions
or as a separate document. The following instructions or the equivalent shall be supplied where applicable:
IMPORTANT INSTALLATION INSTRUCTIONS
a) Install the gate operator only when:
1) The operator is appropriate for the construction of the gate and the usage Class of the gate,
2) All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet
(1.22 m) above the ground to prevent a 2-1/4 inch (57.2 mm) diameter sphere from passing through the openings
anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position,
3) All exposed pinch points are eliminated or guarded, and
4) Guarding is supplied for exposed rollers.
b) The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a
separate access opening. The partial access opening shall be designed to promote pedestrian usage. Locate the gate
such that persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.
c) The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent
structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access
areas.
d) The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. Do
not over-tighten the operator clutch or pressure relief valve to compensate for a damaged gate.
e) The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving and
AWAY FROM THE GATE PATH PERIMETER.
f) Controls intended for user activation must be located at least six feet (6’) away from any moving part of the gate and
where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or
easily accessible controls shall have a security feature to prevent unauthorized use.
g) The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not
cause the operator to start.
h) A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible
International registered trademark n. 2.777.971

i) For gate operators utilizing a non-contact sensor:
1) See instructions on the placement of non-contact sensors for each Type of application
2) Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the
gate is still moving
3) One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the
perimeter reachable by a moving gate or barrier
j) For a gate operator utilizing a contact sensor:
1) One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the
leading edge, trailing edge, and postmounted both inside and outside of a vehicular horizontal slide gate.
2) One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
3) One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.
4) A hardwired contact sensor shall be located and its wiring arranged so that the communication between the
sensor and the gate operator is not subjected to mechanical damage.
5) A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for
entrapment protection functions shall be located where the transmission of the signals are not obstructed or
impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall
function under the intended end-use conditions.
6) One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally,
if the bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of
travel, one or more contact sensors shall be located on the bottom edge.
7) One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).
Instruction regarding intended operation of the gate operator shall be provided as part of the user instructions or as a
separate document. The following instructions or the equivalent shall be provided
NOTICE
As for misunderstandings that may arise refer to your area distributor or call our help desk. These instructions are part
of the device and must be kept in a well known place. The installer shall follow the provided instructions thoroughly.
SEA products must only be used to automate doors, gates and wings. Any initiative taken without SEA USA Inc. explicit
authorization will preserve the manufacturer from whatsoever responsibility. The installer shall provide warning notices
on not assessable further risks. SEA USA Inc. in its relentless aim to improve the products, is allowed to make
whatsoever adjustment without giving notice. This doesn’t oblige SEA to up-grade the past production. SEA USA Inc.
can not be deemed responsible for any damage or accident caused by product breaking, being damages or accidents
due to a failure to comply with the instructions herein. The guarantee will be void and the manufacturer responsibility
will be nullified if SEA USA Inc. original spare parts are not being used. The electrical installation shall be carried out by
a professional technician who will release documentation as requested by the laws in force. Packaging materials such
as plastic bags, foam polystyrene, nails etc must be kept out of children’s reach as dangers may arise.
To respect the norms in force it is recommended to use the ENCODER SYSTEM together with the electronic
control units
International registered trademark n. 2.777.971
Starting on Jan. 12, 2016, new UL 325 changes take effect, bringing a series of new mandates for the gate operator
industry. Here’s a quick guide to the key modifications.
1. Entrapment-Protection Devices. Gate operators are required to have a minimum of two independent means of
entrapment protection where the risk of entrapment or obstruction exists. A manufacturer can use two inherent-type
systems, two external-type systems, or an inherent and an external system to meet the requirement. However, the
same type of device cannot be used for both means of protection.
2. Monitoring Required. An external non-contact sensor or contact sensor may be used as a means of entrapment
protection. However, the sensor must be monitored once every cycle for (1) the correct connection to the operator and
(2) the correct operation of the sensor.
If the device is not present, not functioning, or is shorted, then the gate operator can only be operated by constant
pressure on the control device. Portable wireless controls will not function in this case.
3. Entrapment Risk Identification. As in the past, it’s up to the installer to examine the installation and determine
where a risk of entrapment or obstruction exists. Manufacturers are required to provide instructions for the placement
of external devices, but they give only examples of suggested entrapment protection in their installation manuals. If the
installer identifies a risk of entrapment or obstruction, at least two independent means of entrapment protection are
required.
4.Terminology Change. The terms “primary” and “secondary” have been removed in the description of entrapment
protection devices. This was done to emphasize that all entrapment protection devices are equally important.
Changes to UL 325 ED. 6th for Gate Operators

5. The End of Type E. Type E (audible alarm) devices can no longer be used for entrapment protection. This change
was made because the Type E device is really a warning device, not an entrapment-protection device. Also, all gate
operator classes are now required to have an audio alarm that sounds when two successive obstructions are
encountered via a contact-type system.
6. Access Control Location for Emergency Use. An exception has been added in the manufacturer’s instructional
requirements for the location of controls that operate the gate.
The instructional requirements state that these controls must be at least 6' away from any moving part of the gate. In the
new exception, “Emergency access controls only accessible by authorized personnel (e.g., fire, police, EMS) may be
placed at any location in the line-of-sight of the gate.”
7. Barrier-Arm Operator Exception. An exception has changed for barrier-arm gate operators requiring entrapment
protection. The previous exception stated that a barrier-arm operator did not require entrapment protection if the arm
did not move toward a rigid object closer than 2'. The distance has been reduced to 16" so it more closely aligns with the
industry-defined entrapment protection provisions in ASTM F2200.
8. Gate Operator Class II and Class III Definitions. The definitions for installation classes for gate operators were
modified. Class II now includes commercial locations accessible to the general public. Class III was refined to specify
industrial locations not accessible to the general public. These changes, while seemingly minor, may affect which gate
operator is suitable for a particular installation location.
UL 325 ED. 6th ENTRAPMENT PROTECTION REQUIREMENTS
This vehicular gate operator must be installed with at least two independent entrapment protection
means as specified in the table below.
International registered trademark n. 2.777.971
VERITICAL BARRIER NOTE:
Barrier gate operators (arm) that is not intended to move toward a rigid objact closer than 16 inches (406mm)
are not required to be provided with a means of entrapment protection
* B1 and B2 means of entrapment protection MUST be MONITORED
HORIZONTAL SLIDE
VERTICAL LIFT - VERTICAL PIVOT
ENTRAPMENT
PROTECTION
TYPES
TYPE A
TYPE B1
TYPE B2
TYPE C
Inherent entrapment protection system
Non-contact sensors such as photoelectric sensors or equivalents
Contact sensors such as edge sensors or equivalent devices
Inherent force limiting, inherent adjustable clutch or inherent pressure relief device
The same type of device shall not be used for both entrapment protection means. Use of a single device to cover both
the opening and closing directions is in accordance with the requirement; however, a single device is not required to
cover both directions. Tice installer is required to install entrapment protection devices in each entrapment zone
TYPE D Actuating device requiring constant pressure to maintain opening or closing motion of the gate
SWING
VERTICAL BARRIER (ARM)
A , B1*, B2* or D A , B1*, B2*, C or D
GATE OPERATOR CATEGORY
Effective January, 12 2016
VEHICULAR GATE OPERATOR CLASSES
Residential Vehicular Gate Operator-Class I: A vehicular gate operator (or system) intended for use in garages or
parking areas associated with a residence of one-to-four single families
Commercial/General Access Vehicular Gate Operator-Class II: A vehicular gate operator (or system) intended for
use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel,
garages, retail store, or other buildings accessible by or servicing the general public
Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended for
use in an industrial location or building such as a factory or loading dock area or other locations not accessible by or
intended to service the general public
Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use in an
industrial location or building such as a factory or loading dock area or other locations not accessible by or intended to
service the general public

GATE WARNINGS
The first thing to check is that the gate is in good running order as follows:
A. (Make sure that) the fixed and moving parts of the gate are strong and non-deformable;
B. the weight of each gate leaf must not exceed that indicated on technical specifications of the motor type;
C. the hinges and general structure must be in good condition and the gate must move smoothly throughout
its travel;
D. the upper hinge alone is sufficient to install the unit; those which are unnecessary can be eliminated (the
lower and that in the middle if exists)
GATE WARNINGS AND PRECAUTIONS
Not for pedestrian opening
Fig. 1
Fig. 2
Fig. 3
PRECAUTIONS
This automation has been created for the automation of gates used by
vehicles only. Be aware to avoid the crossing of the gate path because it
is very dangerous for pedestrians (fig. 4).
Fig. 4
Install the warning signs, on each side of the gate and in avisible
zone which informs the pedestrians about the danger they run when
passing or resting in the environment of the gate (fig. 5).
Important:
For a higher security, SEA advices to install infrared photocells.
Fig. 5
International registered trademark n. 2.777.971

7
7,40
12,59
16,14
2,67
2,16
Compact 120V/230V and Super Compact 120V/230Vconsists of a hydraulic pump and a hydraulic jack,
both of which coupled in a supporting box treated with cataphoresis. The pump unit casing, which is
used as an oil tank, contains the electric motor, fluid pump, distributor and hydraulic oil. It is also provided
with an adjustable slowing-down device in the two stop phases of the leaf (versions with slow-down only).
The wheeling unit is composed by a double piston connected to a rack which engages with the pinion of the
leaf dragging shaft. Gates up to 6,5 feet long can be securely locked using the operators internal hydraulic
locking system, thus ensuring perfect keeping in closing and in opening. For gate in excess of stated value: A
hydraulic non locking operator should be used in conjunction with a separate electrical locking device to
ensure keeping in closing. On the operators with hydraulic slow down it is present only during the last
15° of rotation. The system comes with a release which allows the manual opening of the leaves in case of
power failure.
1 Braking regulation screw
(where provided)
2 Emergency release (authorized staff only)
3 By-pass regulation
4 Exit hole for electric cables
5 Filling oil Cap
6 Water draining hole
7 Oil level indicator
8 Draining screw
9 Greaser
10 Crank
MAIN PARTS NOMENCLATURE
Fig.6
9
8
7
4
6
3
2
1
5
10
FEATURES AND SPECIFICATIONS
DIMENSIONS (inches)
Fig.7
GRAPHIC FOR USE OF COMPACT
OPERATORS
6,5 feet
13 feet
1600 pound
COMPACT
1600 AC
COMPACT
1600 AC
Max leaf weight Max leaf width
COMPACT 1600 SB
(With electric lock)
COMPACT 1600 SB
(With electric lock)
16 feet
2600 pound
SUPER COMPACT
2600 AC
SUPER COMPACT
2600 AC
SUPER COMPACT 2600 SB
(With electric lock)
SUPER COMPACT 2600 SB
(With electric lock)
Underground hydraulic operators
International registered trademark n. 2.777.971

8
International registered trademark n. 2.777.971
TECHNICAL SPECIFICATIONS
COMPACT 1600 120V
120V (50/60 Hz)
300 W
2,45 A
1635 rpm
45
50 bar
40 bar
-4°F +131°F
266°F
1056 lbf
60 uF
30,4 Lbs
3R Type
1600 Lbs
TECHNICAL DATA
Power supply
Motor Power
Absorbed current
Motor rotation speed
Cycles hour (with a 68°F temperature)
Max Pressure 0,13 Gal. pump in use
Max Pressure 0,20 Gal. pump in use
Operating temperature
Thermal protection intervention
Max torque
Starting capacitor
Weight
Protection class
Maximum weight of the gate
Maximum leaf length
Braking regulation
230V (50/60 Hz)
220 W
1,35 A
120V (50/60 Hz)
220 W
2,45 A
1530rpm
60
50 bar
-4°F +131°F
3336 lbf
60 uF 10 uF
33 Lbs
3R Type
2600 Lbs
On control unit or on operator *
230V (50/60 Hz)
310 W
1,5 A
COMPACT 1600 230V
SUPER COMPACT 2600 120V SUPER COMPACT 2600 230V
1400rpm
266°F
* In case of operator with hydraulic slow-down
TECHNICAL DATA
Power supply
Motor Power
Absorbed current
Motor rotation speed
Cycles hour (with a 68°F temperature)
Max Pressure 0,40 Gal. pump in use
Operating temperature
Thermal protection intervention
Max torque
Starting capacitor
Weight
Protection class
Maximum weight of the gate
Maximum leaf length
Braking regulation
16 ft
On control unit or on operator *
6,5 feet (13 feet with electric-lock)
* In case of operator with hydraulic slow-down

9
2. TYPICAL INSTALLATION
1) COMPACT/SUPER COMPACT operator
2) Electric lock
3) Electronic Control Unit
4) Photocell tx
5) Photocell rx
6) Photocells
7) Radio receiver
8) Key switch
9) Warning notice inside
10) Warning notice outside
SAFETY LOOP
1
6
6
1
4
2
5
9
8
7
3
10
EXIT LOOP
CENTER LOOP
SAFETY LOOP
IN
OUT
Fig. 8
MECHANICAL INSTALLATION
International registered trademark n. 2.777.971
3. CARRYING BOX INSTALLATION
3.1. The hole which contains the carrying box must have the approximate dimensions mentioned in Fig. 9.
For a correct placing, it is obbligatory to follow closely the quote of 2,16 inches which corresponds to the
minimum distance of the rotation axis from the pillar.
Fig. 9
23,6
17,7
8,4
dimensions (inches)

10
3.2.
Inside the excavated pit you have to plan:
-rain water drainage;
-a water waste pipe in flexible plastic of about 1,5 inches of diameter to put inside the provided hole of the
box before it is concreted (Fig. 10). It must be brought until the drain of the sewer line;
-a sheath for the passage of electrical cables of about 0,8 inches of diameter which must be brought to the
proximity of the electric connection box (Fig. 10).
Fig. 10
Sheath for electric
cables passage
Flexible pipe
for water draining
Electric
connection box
International registered trademark n. 2.777.971
3.3.
Before concreting the carrying box, use a level to make it perfectly horizontal to the ground (Fig. 11) and
perpendicular to the axis of the gate (Fig. 12).
The axis of the upper hinge of the gate must correspond exactly to the axis of the carrying box shaft.
Fig. 11
Fig. 12

11
3.4. introduce the buckle of creeping in the box and fix it with the
special screws (Fig. 13).
3.5. Insert the units as in Fig. 13.
N.B.: During the insertion of the units lubricate them with the
supplied grease.
Fig. 13
International registered trademark n. 2.777.971
4. LEAF ASSEMBLING
Before installing the gate make sure that the concrete has hardened into the foundation hole.
4.1. Place the leaf of the gate on the leaf device making reference to the rotation axe of the leaf hinge (Fig.
14);
Fig. 14
leaf device
leaf rotation axe
leaf
Crank shaft Crank
4.2. Weld with care the leaf device to the leaf of the gate realizing a tract fixation of ca. 1,2-1,6 inches along
the surface of the contact, avoiding the welding next to the threaded holes, furthermore it is necessary to
respect the perpendicularity to the axe of rotation (Fig. 15)
Fig. 15

12
4.3. Be careful not to place the leaf outside the axis (Fig. 17 and 18), but make sure the shaft corresponds to
the hinge rotation axis remembering that the minimum distance from the pillar is 2,16 inches (Fig. 19).
Fig. 16
International registered trademark n. 2.777.971
Fig. 17 Fig. 18
Fig. 19
2,16 inches

13
5. INSTALLATION OF THE OPERATOR
5.1.Insert manually the operator into the carrying box (Fig. 20) also insert the splined shaft of the operator
into the splined bush of the box and fix the operator with the special screws as in Fig. 21.
5.2.Carry out the electrical connections to the control unit as described in the instructions supplied with
SEA control unit.
After ending all the operations in the installation of the above mentioned carrying box, of the gate and the
operator, try to do some moves slowly by hand verifying that there are not irregular frictions and that the
movement is uniform for the whole range.
Notice: To do this last operation, release the operator as described in the next paragraph.
Fig. 20
Fig. 21
N.B.: It is advisable to weld the crank with the
crank shaft also after having installed the Compact
or Super Compact, to use the whole available run
and the point of beginning of the desired
slowdown (version with hydraulic slowdown).
Before welding, make sure that one of the level of
the crank shaft corresponds with a side of the
crank (see fig.21 and 22) to guarantee the
maximum angle with the mechanical stops Kit
Fig. 22
1
2
International registered trademark n. 2.777.971
6. MOTOR RELEASE SYSTEM
6.1. To release act as follows:
-Turn the release screw with the screwdirver about 180° ca. in anti- clockwise direction (Fig. 23).
6.2. To stop again act as follows:
-Turn the release screw with the screwdriver into clockwise direction until it stops.
Fig. 23
N.B.: If the operator is not
installed immediately but in
a second time, it is
recommended to weld the
crank shaft and the crank
during the installation of the
Compact/Super Compact
Lock
Release

14
7. MOUNTING OF THE RELEASE
For Compact or Super Compact operators there are foreseen two types of release:
RELEASE (with personalised key) and RELEASE PLUS (with DIN key).
RELEASE PLUS
7.2. Grease the hinge (A) and mount the release
system under the leaf device using the 5 furnished
screws (Fig. 25).
Carry out the electrical connections to the control unit as described in the instructions supplied with
SEA control unit.
Fig. 24
A
Release
Fig. 25
A
Release Plus
International registered trademark n. 2.777.971
RELEASE
7.1. Grease the hinge (A) and mount the release
system under the leaf device using the 4 furnished
screws (Fig. 24)
8. ADJUSTABLE MECHANICAL STOPS
Fig. 26 Fig. 28
Fig. 27
Fig. 29

15
Fig. 30
0
-15°
105°
Max. Angle with mechanical stops kit
Fig. 31 Fig. 32
RIGHT
LEFT
Outside
Inside
Outside
Inside
Fig. 33
When putting in function the installation it is peremptory to
lubricate the box as in Fig. 31 until the grease comes out.
(Use grease typeDIN 51502 KP 2 N-20 - K 2 K-20)
International registered trademark n. 2.777.971
Fig. 34
+
-
9. REGULATION OF THE PUSHING FORCE
The pushing force or anti-crushing force must be valued by
hand or better with a dynamometer and in both the ways of
rotation.
To regulate such force act as follow:
act on the by-pass valves with the provided key, given to the
authorised installers, clockwise to increase the force, anti-
clockwise to decrease it (Fig. 34). The adjustment is carried out
with the gate moving and will not change the speed of the
leaf.Notice: The maximum regulation is of 33 pound. The motor
run time is the last adjustment to make. It should be set 2 to 4
seconds higher than it takes to the gate to reach its stop. (this
last regulation must be done on the electronic control unit).
10. BRAKING REGULATION (where present)
10.1.It is possible to regulate the leaf slowdown in opening and
in closing, through the braking adjusting screw (Fig. 35).
10.2.To regulate slowdown operate as follow:
- Loosen the blocking screw of braking regulation
- Act on the adjusting screw clockwise to have a higher braking
and a speed decrease;
- Act on the adjusting screw anti-clockwise to have a lower
braking and a speed increase;
- After the regulation fix the blocking screw of braking
regulation.
On the operators with hydraulic slow down it is prensent
only during the last 15° of rotation. Fig. 35
+
-
+
-
Braking regulation screw
Opening/closing
Blocking screw for
braking regulation

16
RELEASE
To release act as follows:
- Insert the enclosed key into the keyhole (S) and
turn the handle about 180° against the centre of the
gate (Fig. 36) .
- Keep the key locked and move the leaf, now turn
back the key to the normal position and extract it.
To stop again act as follows:
- Move the leaf until the lock has coupled again.
RELEASE PLUS
To release act as follows:
- Insert the enclosed key into the keyhole and turn it about 90° in clockwise direction (Fig. 37).
- Pull the key against the external of the release making come out the handle of the lock until it reaches the
stop (Fig.38).
- Move the leaf and make return the handle of the release in its original position and extract the key.
To stop again act as follows:
- Move the leaf until the lock has coupled again.
S
Fig. 36
180°
Fig. 37
90°
Fig. 38
Stop
Release handle
To the attention of users and technicians
International registered trademark n. 2.777.971
RELEASE SYSTEM OF THE LEAVES
11. COMPACT/SUPER COMPACT ACCESSORIES
SAFETY GATE
PHOTOCELLS RADIO RECEIVER
EXTERNAL LOOP
DETECTORS
KEY SWITCH
MAGNETIC LOCK
CARD
TRANSMITTER
FLASHING LAMP BATTERY BACK-UP ELECTRIC LOCK MAGNETIC LOCK

17
International registered trademark n. 2.777.971
To the attention of users and technicians
RISK EXAMINATION
The points pointed by arrows are potentially dangerous. The installer must take a thorough risk examination in fig. 39
to prevent crushing, conveying, cutting, grappling, trapping so as to guarantee a safe installation for people, things
and animals. ( ) As for misunderstandings that may Re. Laws in force in the country where installation has been made.
arise refer to your area distributor or call our help desk. These instructions are part of the device and must be kept in a
well known place. The installer shall follow the provided
instructions thoroughly. products must only be SEA USA Inc.
used to automate doors, gates and wings. Any initiative taken
without explicit authorization will preserve the SEA USA Inc.
manufacturer from whatsoever responsibility. The installer
shall provide warning notices on not assessable further risks.
SEA USA Inc. in its relentless aim to improve the products, is
allowed to make whatsoever adjustment without giving notice.
This doesn’t oblige to up-grade the past SEA USA Inc.
production. can not be deemed responsible for SEA USA Inc.
any damage or accident caused by product breaking, being
damages or accidents due to a failure to comply with the
instructions herein. The guarantee will be void and the
manufacturer responsibility will be nullified if SEA USA Inc.
original spare parts are not being used.
Fig. 39
The electrical installation shall be carried out by a professional technician who will release documentation as
requested by the laws in force. Packaging materials such as plastic bags, foam polystyrene, nails etc must be kept out
of children’s reach as dangers may arise.
PERIODICAL MAINTENANCE
Check the oil level (Trasparent cap n.7 in Fig. 6)
Change the oil
Verify the functionality of the by-pass valves
(check the force in opening and closing)
Check the release function
Verify the slowdown regulation (where present)
Check the correct drain of the rainwater
Check the integrity of the connection cables
Grease all the moving parts
Grease the rotation axis of the box as in Fig.33
Annual
4 years
Annual
Annual
Annual
Annual
Annual
Annual
Annual
All the above described operations MUST be made exclusively by an authorized installer

SALES CONDITIONS and WARRANTY
GENERAL WARNING: Installation must be realized using parts and accessories approved by SEA. SEA is not
responsible for incorrect installations and/or non-compliance with safety standards according to the law in-force.
SEA is in no way liable for any damages and/or malfunctioning due to using parts and accessories non-compliant
with the UL325 safety standards.
ORDERS: Orders are processed upon approval by SEA. Buyers must confirm orders by sending a written Purchase
Orders to SEA. Purchase Orders are intended as confirmation of orders and binding for the buyer, which accepts
SEA sales condition.
QUOTATION: Quotation and special offers with a non-specified duration expires automatically after 30 days.
PRICES: Prices are based on the Price List in force. Discounts and quotation from Sales Rep. and other selling
branches must be approved by SEA. Prices are F.O.B SEA Warehouse in Miami and do not include shipments costs.
SEA reserves the right to modify the price list at any time and provide notice to its sales network.
PAYMENT: Method of payments and terms are notified by SEA and displayed on the commercial invoice.
DELIVERY: The delivery time on the invoice is not binding and represents an estimated delivery. Shipments costs
will be charged to the buyer and SEA is not responsible for delays and/or damages occurred to the products during
shipment.
COMPLAINS: Complains and/or claims must be notified to SEA within 7 business days after receiving the products.
Claims and complains must be supported by original documents. Customer must contact the factory for instructions
and authorization. Merchandise returned for credit must be current, uninstalled and unused and returned in its
original packaging. Freight must be pre-paid on all authorized returns.
REPAIRS: Repairs and parts are subject to the availability in stock. Shipment of products for repairs must be pre-
paid by the customer. Products shipped without authorization, sender’s details and description of the problems will
be refused. Customers must contact SEA for instructions.
WARRANTY: for the original buyer only:
Hydraulic and oil-bath motors: 36 months warranty from the date of invoice on manufacturing, assembling and
workmanship defects.
Electro-mechanic motors and electronic control systems: 24 months warranty from the date of invoice on
manufacturing, assembling and workmanship defects.
Lepus and Full Tank Standard model: 60 months warranty from the date of invoice on manufacturing, assembling
and workmanship defects.
No warranty will be recognized for damages due to incorrect installation and/or improper use for which the product
was intended. SEA warranty obligations shall be limited to repair or replace the defective product/parts at SEA
option, upon examination of the products by SEA technical Staff. All replaced parts must remain property of SEA. The
warranty status of the product remains an unquestionable assessment of SEA. Buyer must ship pre-paid defective
products. Products under warranty will be returned pre-paid by SEA. Recognized defects, whatever their nature, will
not produce any responsibility and/or damage claims to SEA USA Inc and SEA s.r.l. Warranty shall not cover any
required labor activities. Warranty will in no case be recognized if alterations and any other changes will be found on
products. Warranty will not cover damages caused by carriers, expendable materials and faults due to improper use
with the products specifications. No indemnities are recognized during repairing and/or replacing of the products
under warranty. SEA USA Inc. and SEA s.r.l. decline any responsibility for damages to person and objects deriving
from non-compliance with safety standards, installation instructions or use of the products sold. It is intended that
warranty will be recognized only on products bought through the SEA authorized network. Products must be installed
by professionals. No warranty will be recognized if products are installed directly by the final user. Warranty does not
apply in case of unexpected events such as fire, flood, electrical power surge, lightning, vandalism and others.
SEA USA Inc. is not responsible for errors in technical information printed in catalogs and installation
manuals.
International registered trademark n. 2.777.971

SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172 USA
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716
web site: www.sea-usa.com
e-mail: [email protected]
International registered trademark n. 2.777.971