
30 & 50TONNE FLOOR TYPE PREMIER AIR/
HYDRAULIC PRESS
MODEL NO: PPF301S, PPF501S
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Familiarise yourself with the applications, limitations and hazards of the press.
9Maintain the press in good condition (use an authorised service agent).
9Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9Keep the press clean for best and safest performance.
9Locate the press in a suitable work area, on a surface that is stable, level, dry, not slippery, and capable of sustaining the load.
9Keep area clean and tidy and free from unrelated materials, and ensure there is adequate lighting.
WARNING! Always wear approved eye or face protection when operating the press.
9Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9Keep hands and body clear of the work table when operating the press.
9Maintain correct balance and footing. DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes.
9Keep children and unauthorised persons away from the working area.
8DO NOT use the press for a task it is not designed to perform.
8DO NOT adjust or tamper with the safety valve, or make any modifications to the press.
8DO NOT exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied
load.
8DO NOT apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press.
8DO NOT allow the workpiece or the V blocks plates to fall from the press work bench.
8DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
8DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8DO NOT climb upon the press.
8DO NOT use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load.
8DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8DO NOT use the press to compress a spring or any other item that could disengage and cause a potential hazard.
8DO NOT stand directly in front of loaded press and never leave loaded press unattended.
8DO NOT allow untrained persons to operate the press.
▲DANGER! This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or
the workpiece.
WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as
this may cause serious damage to the press and will invalidate the warranty.
9When not in use, release pressure from the pump and clean the press. Stand or store the V blocks in a safe, childproof location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Heavy-duty steel frame construction with integral air motor powering hydraulic pump unit. Screw adjustable ram and adjustable work area
with removable tray. Sliding hydraulic ram assembly giving 280mm of lateral travel for o-centre pressing applications. Frame head tted with
ram pressure gauge. Winch assisted press table adjustment. Storage for press pins included in frame. Supplied with press pins, at pressing
plate/V-blocks.. 2 Year guarantee*. This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery.
PPF301S, PPF501S Issue:2 (3)27/06/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions Wear a face
shield Wear protective
gloves Wear safety
footwear Wear protective
clothing Warning
crushing
of hands
No reaching
in
Place V block
correctly
Piston rod
should face the
workpiece