Sealey PWTF2200 User manual

PRESSURE WASHER TWIN FLOW150BAR
810LTR/HR 230V
MODEL NO: PWTF2200
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the
correct fuse - see fuse rating in these instructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a rm grip on the plug.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualied electrician.
1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch o󰀨 the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
WARNING! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an
electric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.
WARNING! DO NOT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WARNING! Use washer on a at, levelled surface, in an upright position. Failure to do so will invalidate your warranty.
8NEVER lay the washer down during use.
9Ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a check
valve is installed in the supply hose, or at the tap outlet.
9 The supply hose must be reinforced, and have an internal diameter of 1/2”. The water supply must be at least equal to the cleaner
capacity. The water temperature must NOT exceed 122°F (50°C). The water supply pressure must NOT exceed 6 bar (90psi).
9Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.
9 Use where air can freely circulate around the washer to avoid the machine overheating.
9 Keep the washer in good condition. Use an authorised service agent to service the unit. Only use authorised spare parts.
9 Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
9Position the washer as near to the water supply as possible.
WARNING! Ensure all persons and animals keep at a minimum distance of 15mtr from the washer when in use. All persons within
15mtrs shall wear appropriate P.P.E.
WARNING! The pressure washer must only be used with clean water. Unltered water or corrosive chemicals must not be used as
these will damage the cleaner.
9Ensure the nozzle is aimed correctly at the work surface before switching on the machine.
9 Before activating the trigger, grip the gun rmly to counteract the recoil from the high pressure water jet.
Recommended fuse rating
13 Amp
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
DO NOT direct jet
against yourself, other
persons, animals,
electrical equipment or
the machine itself
DO NOT
drink water
from pressure
washer

WARNING! Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and
connectors.
9 If, during operation, power failure occurs turn the electricity and water o󰀨 for safety reasons.
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
WARNING! DO NOT operate the machine without a water supply. Dry running can seriously damage the unit.
WARNING! DO NOT leave the washer switched on for more than 15 minutes without operating the trigger.
8DO NOT obstruct ventilation grilles during operation.
8DO NOT use the washer with ammable or toxic liquids or any other product. Use only recommended detergent. Unapproved
detergents may corrode the machine cover and accessories.
8DO NOT jam the trigger in the operating position.
8DO NOT adjust any internal control valves, as they have been factory set.
8DO NOT connect other appliances to the machine inlet or outlet.
8DO NOT use hoses and ttings other than those designed for use with this machine.
8DO NOT move the unit by pulling the hoses or electrical cables. Use the handle and transport by means of the wheels.
8DO NOT touch plug with wet hands. To avoid the risk of electrocution keep all connections dry and o󰀨 the ground.
8DO NOT direct jet against yourself, other persons, animals, electrical equipment or the machine itself.
8DO NOT use washer if you are tired or under the inuence of alcohol, drugs or intoxicating medication.
8DO NOT allow children or untrained persons to operate the washer.
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
9After use, disconnect washer from electrical mains and water supply and store in a safe, dry, childproof area.
9Protect from freezing conditions during winter.
WARNING! Using the appliance to wash tyres may damage the tyre and can be dangerous.
8DO NOT point the high pressure jet straight at the tyre.
9Always use the appliance at the lowest pressure setting when cleaning in the vicinity of wheels and tyres.
8DO NOT use the “Turbo Lance” for washing any part of the vehicle.
8DO NOT cover the ventilation grilles when the appliance is in use.
WARNING! During operation the appliance must be positioned on a rm, stable surface.
WARNING! DO NOT direct jet against yourself or others in order to clean clothes or foot-wear.
WARNING! Water that has owed through backow preventers is considered to be non-potable.
WARNING! Inadequate extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and
the connection has to kept dry and o󰀨 the ground. It is recommended that this is accomplished by means of a cord reel which keeps
the socket at least 60mm above the ground.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that they DO NOT play with the appliance.
2. INTRODUCTION
Brand new patent design which is tted with 2 pumps giving more washing power when you need it. Fitted with 2 washing programs. Eco soft
cleaning only activates 1 pump when you need to remove light dirt from bicycles, cars or you want fences, outdoor furniture and sun shades
to seem like new. Fast cleaning activates both pumps together and in use with the new twin ow lance gets rid of the toughest dirt and stains
from stone and cement ooring, brick walls, roofs and construction applications. Twin ow lance included will boost cleaning performance on
wide surfaces, saving a lot of your time and e󰀨ort, up to 70%. Fitted with 8m high pressure hose, 5m power cable and heavy-duty wheels.
3. SPECIFICATION
Model No: ............................................................ PWTF2200
Hose Length:..................................................................... 8m
IP Rating: ....................................................................... IPX5
Maximum Inlet Pressure: ..............................................10bar
Maximum Pressure: ..................................... 150bar(2200psi)
Maximum Water Flow:........................................... 13.5ltr/min
Motor Power:...............................................................2500W
Nett Weight: ................................................................... 14kg
Peak Water Temperature: .............................................. 50°C
Rated Pressure: ..........................................................100bar
Supply:............................................................... 230V - 50Hz
Total Stop System: ........................................................... Yes
Water Flow Rate: .................................................... 9.5ltr/min
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited

4. ASSEMBLY
4.1. Check contents against gure 1
WARNING! All installation and assembly operations must be performed with the appliance disconnected from the mains power
supply.
4.1.1 Adjust Handles to correct height, by pressing the top button in the cable tidy hook (g.2).
4.1.2 Unlock the spool handle (g.2).
4.1.3 Slide the lance holder into place (g.2).
g.1 g.2
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited

4.2. CONNECTION TO THE MAINS WATER SUPPLY
4.2.1. The appliance may only be connected directly to the
mains drinking water supply if the supply hose is tted
with a back ow Make sure that the hose is at least Ø
13mm, that it is reinforced and that it is not more than
25m long.
4.3. SUCTION OF WATER FROM OPEN CONTAINERS
1) Screw the inlet hose with lter to the water INLET and
insert it down to the bottom of the container.
2) Vent the air from the appliance:
a) Unscrew the lance.
b) Start the appliance and keep the gun open until there
are no air bubbles in the water owing out.
3) Switch the appliance o󰀨 and screw the lance back on.
N.B.: The maximum suction height is 0.5m. The suction hose
should be lled before use.
4.4. CONNECTING AND SET UP (FIG.5)
4.4.1. Connect the water supply to the inlet on the front of the
machine.
4.4.2. Connect B5 pressure washer hose to
the rear outlet port.
4.4.3. Connect other end of B5 to lance
handle.
4.4.4. Twist the bottom cable tidy hook up to
release all of the cable. (g.2).
4.4.5. Flip the storage compartment out. Use
this to store nozzles that you are not
using (g.2).
4.4.6. Connect the lance to the lance handle
by rmly pushing the lance into the
lance handle and twisting it at the same
time (g.5.B).
4.4.7. Connect nozzle E to lance or connect
C18 and nozzles to lance (g.3).
4.5. WATER SUPPLY CONNECTION
(FIG.5)
● Water outlet (OUTLET)
■ Water inlet with lter (INLET)
WARNING Only clean or ltered water
should be supplied to the appliance.
The ow rate of the water inlet
tap should be equal to the pump ow
rate. Place the appliance as close to
the water supply system as possible.
4.6. ELECTRICAL CONNECTION
WARNING Check that the electrical
supply voltage and frequency (V-Hz)
correspond to those specied on the
data plate.
4.6.1. Use of extension cables Use cables
and plugs with “IPX5” protection level.
The cross-section of the extension
cable should be proportionate
to its length; the longer it is, the greater
its cross-section should be.
4.6.2. Plug in after assembly.
g.3
g.4
g.5
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited

5. OPERATION
5.1. CONTROLS
5.1.1. Starter device (g.1.H). Set the starter device on (ON/I Power Unit) to operate the motor in “Eco Soft Cleaning” mode. Set the starter
device on (ON/II Power Units) to operate the motor in “Fast Cleaning” mode and increase cleaning power by 50%. In this working
mode, on large surfaces the “Twin Nozzle” accessory adapter can be tted to use two nozzles simultaneously and cut working times by
70%. Set the starter device switch on (OFF/0) to stop the appliance.
5.1.2. Water jet control lever (g.6.I).
5.2. START-UP
1) Turn on the water supply tap fully.
2) Release the safety catch (g.6.D).
3) Depress the gun trigger for a few seconds and start up the appliance by setting the starter device in the working position required
(ON/I Power Unit) or (ON/II Power Units).
WARNING Before starting up the appliance check that it is receiving water correctly; use of the appliance without water will damage it.
5.2.1. TSS (Total Stop System), automatic delivery ow cut-o󰀨 system:
5.2.2. When the gun trigger is released the dynamic pressure automatically cuts out the motor;
5.2.3. When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight
delay.
5.2.4. If the TSS is to function correctly, all gun trigger releasing and depressing operations must be at least 4-5 seconds apart. To prevent
damage to the appliance, DO NOT allow it to operate dry and check that it is properly supplied with water. to prevent damage to the
appliance due to an increase in water temperature,
8DO NOT cut o󰀨 the jet of water for more than 5 minutes with the appliance running.
5.3. STOPPING
1) Set the starter device switch on (OFF/0).
2) Depress the gun trigger and discharge the residual pressure inside the pipes.
3) Engage the safety catch (g.6.D).
5.4. RESTARTING
1) Release the safety catch (g.6.D).
2) Depress the gun trigger and discharge the residual air inside the pipes.
3) Set the starter device in the working position required (ON/I Power Unit) or (ON/II Power Units).
5.5. WASHING TYRES (FIG.6)
5.5.1. Using the appliance to wash tyres may damage the tyre and can be dangerous.
5.5.2. Never point the high pressure jet straight at the tyre.
5.5.3. Always use the appliance at the lowest pressure setting when cleaning in the vicinity of wheels and tyres.
5.5.4. Never use the “Turbo Lance” for washing any part of the vehicle.
5.5.5. For further information refer to section: “Recommended cleaning procedure”.
g.6
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited

5.6. REFILLING AND USING DETERGENT
5.6.1. Adjusting the spray pattern. Water ow is adjusted by twisting
the nozzle (g.5).
5.6.2. Adjusting the detergent to deliver detergent at the correct
pressure, set the nozzle (g.6) (where tted) on “ “ or t
the detergent kit (g.7.C13) as shown. The quantity
of detergent delivered is adjusted using the regulator (g.7)
5.6.3. The detergent must be delivered using the accessories and
by the procedures described in point 5.9. Use of a high
pressure hose longer than the one originally supplied with
the appliance, or the use of an additional hose extension, may
reduce or completely halt the suction of detergent. Fill the
tank (g.7) with highly biodegradable detergent.
5.7. SEALEY DETERGENTS:
TFR Premium Detergent with Wax Concentrated 5ltr...SCS001
TFR Detergent with Wax Concentrated 5ltr...................SCS003
Car Shampoo 5ltr ............................................................SCS005
Car Shampoo Premium with Wax 5ltr............................SCS006
5.8. RECOMMENDED CLEANING PROCEDURE
5.8.1. Dissolve dirt by applying the detergent mixed with water to
the surface while still dry. When dealing with vertical
surfaces work from the bottom upwards. Leave the detergent
to act for 1-2 minute but DO NOT allow the surface
to dry. Starting from the bottom, use the high pressure
jet at a minimum distance of 30 cm. DO NOT allow the rinse
water to run onto unwashed surfaces. In some cases, scrubbing with brushes is needed to remove dirt. High pressure is not always
the best solution for good cleaning results, since it may damage some surfaces. The nest adjustable nozzle jet setting or the rotating
nozzle should not be used on delicate or painted parts, or on pressurised components (e.g. tyres, ination valves, etc.). E󰀨ective
cleaning depends on both the pressure and volume of the water used, to the same degree.
6. MAINTENANCE
Any maintenance operations not covered by this chapter should be carried out by an Authorised Sales and Service Centre.
Warning Always disconnect the plug from the power socket before carrying out any work on the appliance.
6.1. CLEANING THE NOZZLE (FIG.8)
1) Disconnect the lance from the nozzle.
2) Remove any dirt deposits from the nozzle hole using the tool
(g.16.C1).
6.2. CLEANING THE FILTER (FIG.9)
Inspect the inlet lter (g.9.L) and detergent lter (if tted) before
each use, and clean in accordance with the instructions
if necessary.
6.3. STORAGE
1) Turn o󰀨 the water supply tap.
2) Discharge the residual pressure from the gun until all the water
has come out of the appliance.
3) Switch the appliance o󰀨 (OFF/0).
4) Remove the plug from the socket.
5) Drain and wash out the detergent tank at the end of the working
session. To wash out the tank, use clean water instead of the
detergent.
6) Engage the gun safety catch (g.6.D).
6.4. END-OF-SEASON STORAGE
6.4.1. Treat the appliance with non-corrosive, non-toxic antifreeze before
storing it away for winter. Put the appliance in a dry place, protected
from frost.
g.7
g.8
g.9
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited

7. TROUBLESHOOTING
Problem Possible causes Remedy
Pump does not reach working pressure
Nozzle worn Replace nozzle
Water lter fouled Clean lter (L) (g.9)
Insu󰀩cient water supply Turn on water supply tap fully
Air being sucked into system Check tightness of hose ttings
Air in pump
Switch o󰀨 the appliance and keep depressing
and releasing the gun trigger until the water
comes out in a steady ow. Switch the
appliance back on again.
Adjustable nozzle not positioned correctly Set nozzle (E) on (+) setting (g.5.C)
Thermostatic valve tripped Wait for correct water temperature to be
restored
Water being sucked from an open container
from a height of more than 0.5m. Reduce the suction height.
Pump pressure drops during suddenly use
Water being sucked from an external tank Connect appliance to the mains water supply
Inlet water too hot Reduce temperature
Nozzle clogged Clean nozzle (g.8)
Inlet lter (L) fouled Clean lter (L) (g.9)
Motor “buzzes” but fails to start
Power supply voltage too low Check that the voltage of the mains power
supply line is the same as that on the plate.
Voltage drop due to use of extension cable Check characteristics of extension cable
Appliance not used for a long period of time Contact your nearest Authorised Service
Centre
Problems with TSS device Contact your nearest Authorised Service
Centre
Motor fails to start
No electrical power Check that the plug is rmly in the socket and
that the mains voltage supply is present (*)
Problems with TSS device Contact your nearest Authorised Service
Centre
Appliance not used for a long period of time
Using the tool (M) unjam the motor through
the hole at the rear of the appliance (in
models with this feature).
Water leakages Seals worn Have the seals replaced at your nearest
Authorised Service Centre
Safety valve tripped and discharging Contact an Authorised Service Centre
Appliance noisy Water too hot Reduce temperature (see technical data)
Oil leakages Seals worn Contact your nearest Authorised Service
Centre
TSS versions only: appliance starts even with
gun trigger released
High pressure system or pump circuit not
watertight
Contact your nearest Authorised Service
Centre
TSS versions only: no water delivery when
gun trigger is depressed (with supply hose
connected)
Nozzle clogged Clean nozzle (g.8)
No detergent sucked in
Adjustable nozzle on high pressure setting Set nozzle (E) on “ “ setting (g.5.C)
Detergent too dense Dilute with water
High pressure hose extension being used Fit original hose
Deposits or restriction in detergent circuit
Flush with clean water and eliminate any
restrictions. If the problem persists, contact
an Authorised Service Centre
Water escapes from thermostat-valve
Water temperature inside pump head
has exceeded max. rated value stated on
nameplate
With appliance in operation, DO NOT stop
the water jet for more than 5 minutes at a
time
(*) If the motor stops and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (Overload cut out has been
tripped). If the problem recurs more than once, contact your nearest Authorised Service Centre.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
PWTF2200 Issue 1 20/12/18
Original Language Version
© Jack Sealey Limited