Sealey PW1500 User manual

INSTRUCTIONS FOR
PRESSURE WASHERS 105BAR WITH TSS
230V
MODEL NOS: PW1500 & PW1500HV
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the
correct fuse - see fuse rating in these instructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a rm grip on the plug.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualied electrician.
1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol ;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8DO NOT connect either wire to the earth terminal.
9 Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
WARNING! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an
electric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.
WARNING! DO NOT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WARNING! Use washer on a flat, levelled surface, in an upright position. Failure to do so will invalidate your warranty.
NEVER lay the washer down during use.
9Ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a check valve
is installed in the supply hose, or at the tap outlet.
9 The supply hose must be reinforced, and have an internal diameter of 1/2”. The water supply must be at least equal to the
cleaner capacity. The water temperature must NOT exceed 122°F (50°C). The water supply pressure must NOT exceed 6 bar.
9Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.
9Use where air can freely circulate around the washer to avoid the machine overheating.
9Keep the washer in good condition. Use an authorised service agent to service the unit.
9 Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
9Position the washer as near to the water supply as possible.
WARNING! Ensure all persons and animals keep at a minimum distance of 15mtr from the washer when in use.
WARNING! The pressure washer must only be used with clean water. Unfiltered water or corrosive chemicals must not be used as
these will damage the cleaner.
9Ensure the nozzle is aimed correctly at the work surface before switching on the machine.
9 Before activating the trigger, grip the gun firmly to counteract the recoil from the high pressure water jet.
WARNING! Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and
connectors.
Recommended fuse rating:
13 AMP
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear Protective
Gloves
Wear Eye
Protection
Wear Protective
Clothing
PW1500, PW1500HV Issue 1 19/12/17

9If, during operation, power failure occurs turn the electricity and water off for safety reasons.
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
WARNING! DO NOT operate the machine without a water supply. Dry running can seriously damage the unit.
WARNING! DO NOT leave the washer switched on for more than 15 minutes without operating the trigger.
8DO NOT obstruct ventilation grilles during operation.
8DO NOT use the washer with flammable or toxic liquids or any other product. Use only recommended detergent. Unapproved
detergents may corrode the machine cover and accessories.
8DO NOT jam the trigger in the operating position.
8DO NOT adjust any internal control valves, as they have been factory set.
8DO NOT connect other appliances to the machine inlet or outlet.
8DO NOT move the unit by pulling the hoses or electrical cables. Use the handle.
8DO NOT touch plug with wet hands. To avoid the risk of electrocution keep all connections dry and off the ground.
8DO NOT direct jet against yourself, other persons, animals, electrical equipment or the machine itself.
8DO NOT use washer if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8DO NOT allow children or untrained persons to operate the washer.
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
9After use, disconnect washer from electrical mains and water supply and store in a safe, dry, childproof area.
9Protect from freezing conditions during winter.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. i INTRODUCTION
Lightweight and powerful entry level unit, designed for domestic and light trade use. Ideal for a range of applications including cleaning vehicles,
patios, decking, motorbikes and barbecues. Fitted with a powerful 1400W motor with 300 litre water flow per hour and a maximum pressure output
of 105bar. Features Automatic Total Stop System (TSS) which switches the motor on and off when the trigger is operated, prolonging motor life.
Fitted with accessory storage and hose/cable hook to ensure unit stays clutter-free and mobile. Supplied with 3mtr hose, spray gun, lance and
detergent bottle. Weighs just 4.66 kg for ease of manoeuvrability.
3. i SPECIFICATION
Model No:...................................................PW1500/1500HV
Maximum Pressure: ..................................... 105bar(1520psi)
Water Flow:...............................................................300ltr/hr
Motor Power:...............................................................1400W
Supply:................................................................. 230V - 13A
Total Stop System: ........................................................... Yes
Hose Length:...................................................................3mtr
Weight:........................................................................ 4.66kg
E󰀨ective Cleaning Power: ................................................. n/a
Rotablast Nozzle® ............................................................ No
Nozzles: ........................................................................... null
Colour ...................................................................Red/Green
4. ASSEMBLY
4.1. CONNECTING THE WATER SUPPLY.
4.1.1. Use a reinforced hose pipe with an internal diameter of 1/2” and connect to the mains water supply.
Before attaching the hose to the pressure washer flush the hose through with some clean water to remove any foreign matter from within
the hose.
Connect ¾” BSP female fitting to inlet on the rear of the machine (Fig.1) ensuring that the filter is in place.
4.2. CONNECTING THE HIGH PRESSURE HOSE.
4.2.1. Attach the high pressure hose to the front of the unit as in fig.2, ensuring the connector is tight. Attach the other end to the gun (fig.3) and
tighten to ensure a leak-free joint.
4.3. ASSEMBLING THE LANCE AND NOZZLE.
4.3.1. Locate nozzle attachment into end of lance and turn 90° until it locks into place.
WARNING! Ensure the nozzle is locked into position, failure to ensure this could result in the nozzle being ejected under high pressure
when operating the gun.
4.4. CONNECTING THE ELECTRICAL SUPPLY.
WARNING! Ensure the On/Off switch is in the ‘Off’ position.
4.4.1. Use an RCD plugged into a 13A mains socket, DO NOT turn the power on. DO NOT touch the plug with wet hands.
Original Language Version© Jack Sealey Limited PW1500, PW1500HV Issue 1 19/12/17
fig.1fig.2
fig.3

5. OPERATION
` WARNING! Ensure you read, understand and apply Section 1 safety instructions.
WARNING! Dry running can seriously damage the unit.
WARNING! Use washer on a flat, level surface, in an upright position. Failure to do so will invalidate your warranty. Never lay the
washer down during use.
WARNING! DO NOT leave washer switched on for more than 15 minutes without operating trigger.
IMPORTANT! The washer motor will stop as soon as the gun trigger is released and will restart when the trigger is squeezed. Always
allow at least 5 seconds between releasing the trigger and restarting.
5.1. PRIMARY CHECKS
Check that the inlet filter is clean; pump delivery and pressure will be reduced if blocked. Never use the machine without a filter (which is
fitted inside inlet connector). Ensure that the water supply, high pressure hose and gun are correctly connected, and that air can freely
circulate around the washer.
5.2. BLEEDING THE GUN
It is very important to bleed the gun before using the pressure washer. Squeeze the trigger BEFORE turning the electrical supply on.
This allows any air trapped inside the pressure washer and gun to be removed before using the unit. Continue holding the trigger for
approximately one minute to allow any excess air out of the unit. Water will flow through the gun at low pressure during this procedure.
5.3. OPERATING THE MACHINE.
5.3.1. Hold the spray gun firmly to counteract the recoil caused by the high pressure of the water. Before switching on ensure that the lance
is not directed at people, objects or animals prior to being directed at the object to be cleaned.
5.3.2. It is recommended that the trigger is depressed before switching on the unit before every use. This reduces the back pressure and
amperage draw which prevents fuses blowing.
5.3.3. Switch the machine on by turning the switch to the ‘On’ position. Point the lance at the object to be cleaned and fully depress the trigger.
When the trigger is released the motor will automatically switch off.
5.4. ADJUSTING SPRAY PATTERN.
5.4.1. The fan nozzle can be continuously varied by rotating the body of the nozzle as indicated in fig.5.
▲CAUTION! The pencil point setting is very aggressive. It is recommended that for most cleaning applications, a twenty degree
spray angle is used to avoid damage to the surface being sprayed.
NOTE: The pressure of the spray on the surface you are cleaning increases as you move the nozzle closer to the surface.
5.5. USING DETERGENT.
5.5.1. Use only detergents approved for use in pressure washers.
5.5.2. Remove the lance from the gun and replace with the detergent dispenser (fig.4).
5.5.3. Fill the detergent bottle with detergent suitable for use with a pressure washer. The detergent will automatically be mixed with the
water and discharged through the nozzle. NOTE: Detergent will only be drawn into the spray if the fan nozzle is used in the fan
(low pressure) setting.(fig.5). Dirt is dissolved by applying detergent to the dry surface.
5.5.4. On vertical surfaces, work from the bottom upwards.
5.5.5. Leave the detergent to act for 1-2 minutes, but DO NOT allow the surface to dry out.
5.5.6. To wash down select the variable spray jet nozzle set on the wide fan setting (fig.5).
5.5.7. When you have finished the soap application, remove the bottle and flush clean water through the tube until it is cleaned thoroughly.
NOTE: Failure to clean properly will cause the injection system to become clogged and inoperable.
5.6. WHEN WASHING IS COMPLETED.
5.6.1. Switch the power supply off by turning switch to ‘Off’ position.
5.6.2. Turn off the water supply tap.
5.6.3. Discharge residual pressure by pressing the trigger until no more water comes out of the nozzle.
WARNING! Failure to discharge pressure could result in personal injury.
5.6.4. Disconnect the inlet and high pressure outlet hoses.
5.6.5. Wipe the machine clean and dry and store in a clean, safe, dry, childproof location.
NOTE: DO NOT leave motor switched on for more than 15 minutes without operating trigger. If the water pressure drops (e.g. someone
else using the same water supply), the washer will not operate correctly. In this situation immediately switch the motor off and wait until
the pressure is restored.
Original Language Version
© Jack Sealey Limited PW1500, PW1500HV Issue 1 19/12/17
g.5
g.4

6. TROUBLESHOOTING
SYMPTOMS REASON REMEDY
Motor will not start. 1. Loose or disconnected plug.
2. Blown fuse.
1. Reconnect plug.
2. See below
Circuit breaker trips or fuse blown. 1. Circuit Overload.
2. Extension cord too long or wire size too
small.
3. Nozzle partially blocked, causing
excessive pressure.
1. Check that the circuit is rated 13amps or
greater. Disconnect all loads on the circuit.
2. Use proper extension cord as
recommended in section 1.
3. Clean nozzle as described in maintenance
section.
Water or oil leaking from bottom of pump. 1. A small amount of leakage is normal. 1. If excessive leaking occurs contact
authorised service agent.
Trigger will not move. 1. Gun safety lock engaged. 1. Release safety lock.
Unit will not stop when trigger is released. 1. Trigger system not operating properly. 1. Contact authorised service agent.
Motor running but pump not building
maximum pressure or has irregular pres-
sure.
1. Water supply not turned on.
2. Unit has been stored in freezing
temperatures.
3. Water inlet screen clogged.
4. Kink in supply hose.
5. Nozzle worn out.
6. Air in pump.
7. Suction or discharge valves clogged or
worn out.
1. Turn on water supply.
2. Thaw out unit completely including hose,
gun and attachments.
3. Clean screen as described in maintenance
section.
4. Straighten hose.
5. Replace nozzle.
6. Let pressure washer run with gun open
and lance removed until a steady stream
of water is released.
7.Contact authorised service agent.
7. MAINTENANCE
WARNING! Ensure the pressure washer is switched off and unplugged from the mains electrical power supply and turned off at
the mains water tap before performing any maintenance tasks. Check, clean or renew the inlet filter (which is fitted inside the
inlet connector,) after every 50 hours of use.
7.1. NOZZLES.
7.1.1. Ensure that both nozzles are kept clean and free of debris.
7.1.2. The variable nozzle should be lubricated regularly. Clogging of the nozzle causes the pump pressure to be too high and cleaning is
immediately required.
7.1.3. Clear the nozzle of any debris.
7.1.4. Flush the nozzle with water.
7.2. WATER FILTER.
7.2.1. The pressure washer is equipped with a water inlet filter to protect the pump.
7.2.2. To clean the conical filter, remove quick fit connection and the filter from the pump inlet.
7.2.3. Backflush the filter to clean.
7.2.4. Replace filter and quick connection immediately to prevent any ingress of foreign matter into the pump.
7.3. COOLING SYSTEM.
7.3.1. The air vents, in and around the pressure washer, must be kept clean and free of any obstructions to ensure proper air cooling of the
motor during operation.
WARNING! Prevent water from penetrating the vents of the pressure washer to minimise the risk of damage to the machine and to
reduce the risk of shock to the operator.
7.4. GENERAL.
7.4.1. Check unit, gun, nozzle, hose, connections and cables for damage. Immediately replace or repair with genuine parts.
7.5. STORAGE.
7.5.1. Store in a location where the washer will not be subject to freezing conditions.
7.5.2. Make sure that the pressure washer has been drained of water and remove the hoses.
Original Language Version
© Jack Sealey Limited PW1500, PW1500HV Issue 1 19/12/17

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
PW1500, PW1500HV Issue 1 19/12/17
Original Language Version
© Jack Sealey Limited