Sealey VS7020.V3 User manual

 WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using
tools.
DO NOT use tools if damaged or worn.
Maintain the tools in good and clean condition for best and safest performance.
Ensure all threads are clean and well lubricated.
Ensure vehicle is adequately supported with axle stands, ramps, etc. as appropriate.
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
Account for all tools and parts being used and DO NOT leave them in or on the vehicle.
IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or proprietary manual, to establish the correct procedure and
data for the specific vehicle you are working on. These instructions for use are provided as a guide only.
INSTRUCTIONS FOR:
WHEEL BEARING
REMOVAL / INSTALLATION KIT
MODEL No: VS7020.V3
Comprehensive kit of tools for the fast and effective removal and Installation of wheel bearings on front-wheel drive vehicles. Reduces chances of
damage to hub and bearing. Heavy-duty steel drifts with phosphate coating to prevent corrosion. Heavyweight drive screw for use with impact tools.
Also suitable for removing and installing large industrial bearings. Supplied in carry-case.
Model No: VS7020.V3
Drift Sizes Ø: 55, 60, 64, 67, 73, 75, 78, 82, 84, 88mm
End Cap Ø: 50mm
Sleeve Ø External: 76, 86, 92, 101mm
Hub screw length: 210mm
Hub screw drive: 32, 38mm
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATIONS
Refer to
instruction
manual
Wear eye
protection
VS7020.V3 Issue: 2(I) - 16/12/15
Original Language Version
© Jack Sealey Limited
4. CONTENTS

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, dispose of the product according to local regulations.
BEARING REMOVAL: Identify the correct sleeve (6) to sit on the
outside of the bearing housing and the correct drift (3) to drive the
bearing from the housing. Assemble as shown in g.1A using the correct
sleeve cap (7). Keep the hub screw and nut well lubricated whilst driving
out the bearing.
BEARING INSTALLATION: Identify the correct sleeve cap (7) to sit on
the outside of the bearing housing and the correct diameter drift (3) to
drive the new bearing into the housing. Assemble as shown in g.1B.
Keep the hub screw and nut well lubricated whilst driving the new
bearing into the housing. The 50mm end cap is used to locate into the
back of the drifts; they can then be used in a workshop press when it is
not possible to use the hub screw.
5. OPERATION
g.1
1. HUB SCREW NUT 5. VEHICLE HUB
2. WASHER 6. SLEEVE
3. DRIFT 7. SLEEVE CAP
4. BEARING 8. HUB SCREW
VS7020.V3 Issue: 2(I) - 16/12/15
Original Language Version
© Jack Sealey Limited