Seaory S22 Instruction manual


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com








Quick User Guide
Seaory S22 Desktop Double-side Card Printer


Shenzhen Seaory Technology Co., Ltd.


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com
1. Unpacking and inspection


Accessories box
Output hopper
PE foam
S22 card printer
If the above accessories are in short supply, please contact your local distributor immediately.
3) Appearance introduction:
1) Open the top cover ,you will see following items:
2) Accessories list: 
1PC USB cable
1PC power adapter
1PC output hopper
1PC power cable
1PC weight module
1PC cleaning roller
5pcs cleaning card
1PC warranty card
1PC cleaning stick
1PC ICARDE software CD
Output
hopper
Control panel
buttons
LCM screen
Error
indicator
lamp (Red)
Air vent
Switch of upper
cover
Input hopper
Status indicator
lamp (Green)
Power switch
Power
Interface: USB
Interface: Ethernet
Defective card slot


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com
2. Cleaning Roller Installation








.







3. Ribbon Installation 

















4.Take the cleaning roller’s both
sides by hand. After pushing into
the mounting position, gently
press down.
2.Open upper cover ,take out
the ribbon cartridge.

Ribbon cartridge
1. Open the upper cover, take
out the ribbon cartridge, install
the ribbon into the cartridge
according to the color direction.
2.Red roller supply with unused ribbon.
White roller supply with used ribbon.
3. Take ribbon cartridge’s side, Red
roller close to the Back-end card exit
mouth, install the ribbon cartridge.
3. Remove 3M hyaline
layer on cleaning roller
surface.
The purpose of the cleaning wheel is to absorb the dust on the card and improve the
p
rintin
g
effect. Re
p
lace cleanin
g
roller after ever
y
roll of ribbon use u
p
.
In order to ensure the normal use of the printer, please use Seaor
y
ori
g
inal ribbon.
1. Gently lift the upper
cover switch.



Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com
4. Place the card, Add the weight module









„ 5. Adjust the thickness of card feeding entrance
„









 
6. Output Hopper Installation











1.Open the input hopper
dust cap.
2.Place the card into the input hopper
Contact chip cards require the chip
face up,otherwise data cann’t be read
or written to the chip card.
3.Add the weight module. It’s function
is to increase the friction between the
card and the roller, making the card
feeding more smooth.
1. Open the upper cover.
2. Move the yellow lever to adjust
the feed card thickness. 3.Support 0.3mm to 1.0mm thickness
cards. Factory preset thickness is 0.8mm.
2.Installation finished.
1. Attach output hopper to the hole where the
arrow
p
oints.
The feed card thickness needs to be adjusted according to the card’s actual thickness . Like when it’s
0.76mm standard card, the feed card thickness can be set at 0.8mm. If the card feed thickness value is
set too high, it is easy to enter two cards at the same time; if it is set too small, it is easy to fail to
enter the card.
The card slot is used to connect printed cards,please keep it properly.


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com
7. Driver installation



































1.Power adapter 24V connector is inserted into card
printer power interface. Connect the power cable to the
power adapter. Then plug the power cable into the mains
socket. But do not power on until the driver installation is
co
m
p
l
ete
.
2. Connect the square port of the USB
cable to the card printer and connect the
flat port to the USB port of the computer.
3.Use CD-rom or download the driver installation
package on the Seaory's official website,
double-click above driver installation package.
4.Click “Install”.
5. Begin to install, please wait for a while. 6. During the installation process, when the above page
appears. Please select always trust software from
“Shenzhen Seaory Technology CO., LTD ” in the pop-up
windows, then click the “Install” button.
Please install driver by administrator and close all antivirus applications before installation.


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com











8. Driver setting

























7. Wait for one minute, this page appears, click
"finish".

8.Turn on power switch, then the driver will be install
automatically. After installation, please click “Control
panel – Hardware and sound – Devices and printers”
then you can find Seaory S22 was installed
completely.
2. Enter the printing preferences setting page.
1. In "devices and printers", right click on the printer
named "Seaory S22" and select "print preferences".


Seaory S22 desktop card printer quick user guide

Excellent quality, Perfect service www.seaory.com

















9. Print test






3. This picture shows the printer default Settings.The relevant settings can be adjusted according to
different requirements. Please refer to the operation manual for detailed setting.
After all the above steps are completed, relevant software can be used to print and test the card printer. You can
also do print test through Seaory's " iCARDE " software. For details, please refer to Seaory iCARDE manual.