Seaory R600M Operating manual

Shenzhen Seaory Technology Co., Ltd.
01 www.seaory.com 2 Exellent quality, Perfect service
1. Introduction to Product Components
1.1 Front-end View
1.2 Back-end View
Ethernet interface: RJ45 interface, TCP/IP protocol, the network connection
between the PC and the printer can be realized through this interface
USB interface: USB-B type interface, directly connected to the PC.
Power interface: connect to AC power 100-240VAC, 50/60Hz, 4A.
Power switch: turn on and off the card printer circuit.
Back-end output card slot: The printed card is ejected from here, supslot
manual feeding card on back-end and recycling pending card.
2.3 Front-end View
Front-end input slot: The printer defaults to the input slot at the factory, and it
can also be set as the output slot.
Cleaning module door: Open this door to install the cleaning module.
Quick Use Guide
Self-service Kiosk Retransfer Dual-sided Card Printer
Model: Seaory R600M
Ethernet interface
Power switch
USB interface
Power switch
Back-end output card slot
Flattening modular door switch
Ribbon door
Back-end output card slot
Read before use: This manual only briefly describes the
basic installation and use. If you need to know more
about the use, installation and functional characteristics
of this product or have other questions, please refer to
the product manual of the corresponding model.
Ribbon door pull ring
Clean module door
Front-end input slot

Shenzhen Seaory Technology Co., Ltd.
03 www.seaory.com 4 Exellent quality, Perfect service
2. Unpacking Inspection
Check whether the appearance is intact after opening the outer box, and
check whether the accessories are complete according to the product instruction
manual (prevailed by the sales contract). If there is any missing, please contact
the dealer to communicate and solve.
3. Install Accessories and Consumables
3.1 Install Cleaning Module (Top)
(1) Take out the cleaning module and cleaning roller from the accessory box
of the card printer, and assemble them as shown in the picture below.
After tearing off the 3M adhesive layer, hold the two ends of the cleaning roller
with your hands, push them to the installation position and gently press down to
lock the two ends of the cleaning roller.
(2) Press the red frame part of the upper door in the below left picture, open
the upper door after the upper door lock pops out.
(3) Press the assembled cleaning module as shown in the picture below and
install it into the card printer, and then close the upper door to complete the
installation of the cleaning module (top).
Note: The purpose of the cleaning roller is to absorb the dust on the card and
improve the printing performance.

Shenzhen Seaory Technology Co., Ltd.
05 www.seaory.com 6 Exellent quality, Perfect service
3.2 Install the Cleaning Module (Below).
(1) There is a cleaning module door cover under the front entrance/exit slot
of the card printer, lift it out according to the following picture.
After opening the door of the cleaning module, insert the assembled cleaning
module as shown in the below left, and then press the cleaning module to place it
vertically as shown in the lower center.
After above steps are completed, then close the upper door to complete the
installation of the cleaning module (bottom).
3.3 Consumables Preparation
Take out the ribbon and transfer film from the consumable packaging box,
open the corresponding blister boxes respectively and take out the ribbon and
transfer film.
(1) Remove the Consumables Holder:
Pull the ribbon door ring as shown below, open the ribbon door, turn the
handle of the consumable holder, and take out the consumable holder.

Shenzhen Seaory Technology Co., Ltd.
07 www.seaory.com 8 Exellent quality, Perfect service
(2) Install the Ribbon and Transfer Printing:
Install the transfer film and ribbon into the consumable holder as shown below.
4. Hardware Connections
Take out the power cable and USB data cable from the accessory box of the
card printer's outer packing box. The USB-A type interface is connected to the
computer, and the USB-B type interface is connected to the USB interface of the
printer.
Ethernet communication interface installation: RJ45 network interface ,568B
connection mode.
Note: supslot USB and Ethernet communication interface. It’s recommended
that to choose one of them.
Mains socket
Ribbon installation
Transfer film installation
Pay attention to the
installation direction,
the gear is facing up!
Interchanger
Card printer
PC

Shenzhen Seaory Technology Co., Ltd.
09 www.seaory.com 10 Exellent quality, Perfect service
5. Install Card (Insert Card)
(1) Front-end Input Card
When the card printer is ready, put the card into the front input/output slot, the
machine will automatically swallow the card into the internal track of the device
after detecting the card.
There is no requirement for the direction of contactless IC cards and
ordinary white cards, the card insertion direction can be customized
according to needs.
The contact IC card should be inserted strictly in accordance with the
card direction in the picture below, which is consistent with the ATM
card insertion rules. If you only need to print and don't need to encode
chip data, there is no requirement for the direction of the card. The
card insertion direction can be customized according to needs.
The ISO7811 standard card should be inserted strictly according to
the card direction in the picture below, so that the magnetic stripe
position is at the bottom right of the card, which is consistent with the
ATM card insertion rules. If you only need to print and do not need to
encode magnetic stripe data, there is no requirement for the card
direction, it can be customized according to your needs.
Note: If you need to understand the operation requirements of card input
from the back, please refer to the product manual of the corresponding model.
This manual will not explain it in detail.
Front input/output slot
Contact IC card
If it is a contactless IC card and ordinary white card, there is no
requirement for the card direction, you can customize the card
direction according to your needs.
The position of the magnetic
stripe is at the bottom right of
the card
Back input/output slot
Contact IC card

Shenzhen Seaory Technology Co., Ltd.
011 www.seaory.com 12 Exellent quality, Perfect service
6. Print Test
6.1 Install the Driver
Download the installation package from the CD in the accessory box or the
company’s official website www.seaory.com. And install the driver according to the
software installation process prompts or the product instruction manual of this
model.
6.2 Print Test
(1) Driver Test Page
Step 1: In the list of printers and devices → right-click the Seaory R600M
printer icon → printer properties.
Step 2: After enter below picture interface, place some white card into input
hopper, then click” Print Test Chart”.
Step 3: When print out the following card, that’s mean the driver program
and hardware installation are normal.

Shenzhen Seaory Technology Co., Ltd.
013 www.seaory.com 14 Exellent quality, Perfect service
(2) Seaory iCARDE Card Design Software
After all the above steps are completed, relevant software can be used to
print and test the card printer. You can also do print test through Seaory’s iCARDE
software. For details, please refer to Seaory iCARDE manual.