Seaory R600 Operating manual

Shenzhen Seaory Technology Co., Ltd.
1 www.seaory.com 2 Exellent quality, Perfect service
1. Introduction to Product Components
1.1 Front-end View
1.2 Back-end View
Ethernet interface: RJ45 interface, TCP/IP protocol, the network connection
between the PC and the printer can be realized through this interface
USB interface: USB-B type interface, directly connected to the PC.
Power interface: connect to AC power 100-240VAC, 50/60Hz, 4A.
Power switch: turn on and off the card printer circuit.
Back-end output card slot: The printed card is ejected from here, supslot
manual feeding card on back-end and recycling pending card.
1.3 Front-end View
Input hopper: Blank card storage area, capacity: 200pcs standard
card(0.76mm).
Defective card slot: Defective cards storage area, capacity: 25pcs standard
card(0.76mm).
Quick Use Guide
Desktop Retransfer Dual-sided Card Printer
Model: Seaory R600
Ethernet interface
Power switch
USB interface
Power switch
Back-end output card slot
Defective card slot
Input hopper
Output hopper
Flattening modular door switch
Input hopper
Ribbon door
LCM Display
Read before use: This manual only briefly describes the
basic installation and use. If you need to know more
about the use, installation and functional characteristics
of this product or have other questions, please refer to
the product manual of the corresponding model.

Shenzhen Seaory Technology Co., Ltd.
3 www.seaory.com 4 Exellent quality, Perfect service
2. Unpacking Inspection
Check whether the appearance is intact after opening the outer box, and
check whether the accessories are complete according to the product instruction
manual (prevailed by the sales contract). If there is any missing, please contact
the dealer to communicate and solve.
3. Install accessories and consumables
3.1 Install Cleaning Module (Top)
(1) Take out the cleaning module and cleaning roller from the accessory box
of the card printer, and assemble them as shown in the picture below.
After tearing off the 3M adhesive layer, hold the two ends of the cleaning roller
with your hands, push them to the installation position and gently press down to
lock the two ends of the cleaning roller.
(2) Press the red frame part of the upper door in the below left picture, open
the upper door after the upper door lock pops out.
(3) Install the assembled cleaning module above (press vertically) into the
card printer as shown in the picture below:

Shenzhen Seaory Technology Co., Ltd.
5 www.seaory.com 6 Exellent quality, Perfect service
3.2 Install the Input Hopper
First take out the input hopper from the accessory box, turn 90° to open the
card foundation, and then press the slot to the end vertically as shown in the
picture below.
3.3 Install the Output Hopper
Take out the output hopper from the accessory box. There are two holes
under the card outlet at the back of the card printer. Insert the card slot hooks into
the two holes below the card outlet as shown in the picture below.
3.4 Consumables Installation
Take out the ribbon and transfer film from the consumable packaging box,
open the corresponding blister boxes respectively and take out the ribbon and
transfer film.
(1) Remove the Consumables Holder
Pull the ribbon door ring as shown below, open the ribbon door, turn the
handle of the consumable holder, and take out the consumable holder.

Shenzhen Seaory Technology Co., Ltd.
7 www.seaory.com 8 Exellent quality, Perfect service
(2) Install the Ribbon and Transfer Film
Install the transfer film and ribbon into the consumable holder as shown below.
4. Hardware Connections
Take out the power cable and USB data cable from the accessory box of the
card printer's outer packing box. The USB-A type interface is connected to the
computer, and the USB-B type interface is connected to the USB interface of the
printer.
Ethernet communication interface installation: RJ45 network interface ,568B
connection mode.
Note: supslot USB and Ethernet communication interface. It’s recommended that
to choose one of them.
Mains socket
Ribbon installation
Transfer film installation
Pay attention to the
installation direction, the
gear is facing up!
Interchanger
Card printer
PC

Shenzhen Seaory Technology Co., Ltd.
9 www.seaory.com 10 Exellent quality, Perfect service
5. Install Cards and Place the Counterweight Card
5.1 Introduction of Using the Input Hopper
Press the yellow button in the input hopper and turn the door cover 90° to
open the hopper door as shown in the picture below.
5.2 Install Cards
You can put cards into the input hopper after the card printer installation is
completed.
There is no requirement for the direction of contactless IC cards and
ordinary white cards, the card insertion direction can be customized
according to needs.
The contact IC card should be inserted strictly in accordance with
the card direction in the picture below, which is consistent with the
ATM card insertion rules. If you only need to print and don't need to
encode chip data, there is no requirement for the direction of the
card. The card insertion direction can be customized according to
needs.
ISO7811 standard magnetic stripe card should be inserted strictly in
accordance with the card direction in the picture below, which is
consistent with the ATM card insertion rules. If you only need to print
and don't need to encode chip data, there is no requirement for the
direction of the card. The card insertion direction can be customized
according to needs.
5.3 Place Counterweight Card
Take out the counterweight card from the accessory box after installing the
card and place it in the card slot.
Counterweight card: Apply gravity to the card to ensure stable card insertion when
the number of cards in the card slot is small.
Input card roller
No card sensor
As shown in the figure,
the chip position is facing
forward and upward.
As shown in the figure,
the magnetic stripe is
facing the lower right.
Counterweight card

Shenzhen Seaory Technology Co., Ltd.
11 www.seaory.com 12 Exellent quality, Perfect service
Note: If you need to understand the operation requirements of card input
from the back, please refer to the product manual of the corresponding model.
This manual will not explain it in detail.
6. Print Test
6.1 Install the Driver
Download the installation package from the CD in the accessory box or the
company’s official website www.seaory.com. And install the driver according to the
software installation process prompts or the product instruction manual of this
model
6.2 Print Test
(1) Driver Test Page
Step 1: In the list of printers and devices → right-click the Seaory R600
printer icon → printer properties.
Step 2: After enter below picture interface, place some white card into input
hopper, then click” Print Test Chart”
Step 3: When print out the following card, that’s mean the driver program
and hardware installation are normal.

Shenzhen Seaory Technology Co., Ltd.
13 www.seaory.com 14 Exellent quality, Perfect service
(2) Seaory iCARDE card design software
After all the above steps are completed, relevant software can be used to
print and test the card printer. You can also do print test through Seaory’s iCARDE
software. For details, please refer to Seaory iCARDE manual.