SEH myUTN-120 User manual

Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡[phone]
@[email protected]
USB SDCardserver
myUTN-120
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-120. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-120. Sie erhalten die folgenden
Informationen:
Allgemeine Information
Sicherheitsvorschriften
Hardware-Installation
Software-Installation
Erste Schritte
UTN-Server konfigurieren
Beachten Sie das Inhaltsverzeichnis auf
Seite 17. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support-
Hotline.

2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.

Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Scope of Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . 10
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 12
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 13
Connecting SD Card Reader and USB Device to the Client 14
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 15
 Table of Contents

4 [en] Quick Installation Guide
General Information
Purpose
The USB SDCardserver 'myUTN-120' is a network-ready SD card reader. In
addition, the myUTN-120 allows you to access a non-network-ready USB device
(e.g. hard disk, etc.) in the network. The USB device will be connected to the USB
port of the myUTN-120. The software tool 'SEH UTN Manager' handles the access
of the SD card reader and the USB device.
The SEH UTN Manager is installed on all clients that are intended to access the SD
card reader or a USB device in the network. The SEH UTN Manager shows the
availability of all devices in the network and establishes a connection between
the client and the SD card reader or USB device.
The administration of the myUTN-120 is done via the 'myUTN Control Center'.
Scope of Supply
Please check the package content before getting started:
UTN server USB SDCardserver 'myUTN-120'
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-120.
(This document)
Power pack External power pack

Quick Installation Guide [en] 5
Technical Data
Properties Values
Network connection logical:
physical: - IEEE 802.3
- RJ-45 (S/UTP Cat. 5)
Device connection - 1 x USB 2.0 HS
- 1 x SD card reader
SD card reader Card types: - SD, SDHC
Current input - 650 mA @ 5 VDC (without load)
- 1150 mA @ 5 VDC (with full load on the USB port)
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity: 20 - 80 %
Dimensions - Width: 140 mm
- Height: 32 mm
- Depth: 99 mm
- Weight: 140 g
1) SD card reader
2) USB port
3) Link LED (green)
4) Activity LED (yellow)
5) Status LED (green)
6) Power LED (yellow)
7) LED for the SD card reader (green/
orange)
8) LED for the USB port (green/orange)
9) Network connector (RJ-45) for
1000BaseT, 100BaseTX and 10BaseT
10) Reset button
11) Connector for the included power pack
Front view
Rear view

6 [en] Quick Installation Guide
LED Display
The LEDs of the UTN server provide information about its status.
LED Action Color Description
Link permanently on
permanently off
green
-
There is a connection to the network.
There is no connection to the network.
Activity blinksatirregular
intervals yellow Indicates the exchange of network data packets.
Status permanently off
blinks 3 times
blinks 2 times
-
green
green
If the activity LED blinks periodically at the
same time, the BIOS mode is signalized.
Indicates the assignment of a ZeroConfig IP
address.
Indicates the assignment of an IP address
that does not correspond to 0.0.0.0 or that
comes from outside the ZeroConf range.
Power permanently on
permanently off
yellow
-
The device is powered.
The device is not powered.
SD card reader permanently off
permanently on
permanently on
-
green
orange
No SD card is available in the card reader.
An SD card is available in the card reader.
The SD card in the card reader is activated.
USB port permanently off
permanently on
permanently on
-
green
orange
No USB device is connected to the port.
A USB device is connected to the port.
The USB device on the port is activated.

Quick Installation Guide [en] 7
Safety Regulations
UTN servers are network devices for use in office environments. The myUTN-120
is designed for the integration of USB devices and SD cards into TCP/IP networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
If the supplied power cord cannot be used in your country, acquire an
appropriate power cord that suits national provisions. For more information,
please consult your retailer.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
The device must only be operated using the power pack included in the
package.
Only use a certified USB cable (< 3 m) listed at www.usb.org.

8 [en] Quick Installation Guide
Hardware Installation
You can directly connect one USB device to the UTN server (myUTN-120). You
can read and write SD cards via the SD card reader.
Do not connect devices with power supply solely via the USB port to the
UTN server.
Proceed as follows:
1. Connect the UTN server and the USB device to the USB data
cable.
2. Insert the SD card into the SD card reader.
3. Connect the network cable (RJ-45) to the UTN server.
4. Connect the power cord to the UTN server.

Quick Installation Guide [en] 9
Software Installation
The software tool SEH UTN Manager handles the access of the SD card reader and
the USB device. The SEH UTN Manager is installed on all clients that are intended
to access USB devices in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service 'SEH UTN Service'. A detailed description can be found in
the myUTN User Manual.
Make sure that:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
First, you have to download the installation file for the SEH UTN Manager from
the homepage of SEH Computertechnik GmbH:
http://www.seh-technology.com/products/usb-device-servers/products/
myutn-120-downloads.html
Scan this QR code using your smart phone to get direct access to the homepage.
Proceed as follows:
1. Start the installation file.
2. Follow the installation routine.
The SEH UTN Manager is installed on your client.

10 [en] Quick Installation Guide
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected
devices – will be shown in the 'network list'. The preferred devices will be selected
and added to the 'selection list'. The devices in the selection list can be connected
to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 11
’Assigning an IP Address to the UTN Server’ 12
’Adding the UTN Server to the Selection List’ 13
’Connecting SD Card Reader and USB Device to the Client’ 14
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a
secure UTN SSL port. A detailed description can be found in the myUTN User Manual.
Detailed information on how to use the SEH UTN Manager can be found
in the Online Help. To start the Online Help, select Help – Online Help
from the menu bar.


Quick Installation Guide [en] 11
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> All Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
During the initial configuration, client and UTN server must be assigned to the
same local network segment.

12 [en] Quick Installation Guide
Assigning an IP Address to the UTN Server
Once the UTN server is connected to the network, it checks whether an IP address
can be obtained from the boot protocols BOOTP or DHCP. If this is not the case,
the UTN server assigns itself an IP address via ZeroConf from the address range
(169.254.0.0/16) which is reserved for ZeroConf.
The UTN servers found by the program will be displayed in the network list. You
can change the TCP/IP parameters of the UTN server.
Proceed as follows:
1. Confirm the note dialog 'Your Selection List seems to be empty' by clicking
Yes.
If no note dialog is available and the main dialog appears, select Selection List – Edit
from the menu bar.
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Select Set IP Address from the shortcut menu.
The Set IP Address dialog appears.
4. Enter the relevant TCP/IP parameters.
5. Click OK.
The settings are saved.

Quick Installation Guide [en] 13
Adding the UTN Server to the Selection List
In order to connect a UTN server to a client, you must assign the UTN server to
the selection list. Put together a selection list with your preferred UTN servers.
Proceed as follows:
1. Select Selection List – Edit from the menu bar.
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Click Add.
(Repeat steps 2 and 3, if necessary.)
4. Click OK.
The UTN servers are shown in the selection list.
You can extend the search for UTN servers to any network range. To do this,
change the search parameters for the network scan via the Options dialog in the
Program menu.

14 [en] Quick Installation Guide
Connecting SD Card Reader and USB Device to the Client
SD card readers and USB devices that appear in the selection list can be
connected to the client.
Make sure that:
- All provisions (driver installation, etc.) necessary to operate the device locally
(i.e. connected directly to the client) have been met on the client. Ideally, the
device has been connected and operated on the client locally according to
the instructions of the manufacturer.
- The device is not connected to another client. A device that was made
available by the UTN server can only be used by one network participant at a
time.
Proceed as follows:
1. Mark the relevant USB device in the selection list.
2. Select Device – Activate from the menu bar.
The connection will be established.
Close the connection to the device when the device is no longer needed. Select
Device – Deactivate from the menu bar.

Quick Installation Guide [en] 15
Configuring the UTN Server
The UTN server can be configured and monitored via the myUTN Control Center.
The myUTN Control Center is stored in the UTN server and can be launched by
means of a browser (Internet Explorer, Firefox, Safari).
Proceed as follows:
1. Open your browser.
2. Enter the IP address of the UTN server as the URL.
The myUTN Control Center appears in the browser.
If the myUTN Control Center is not displayed, check the proxy settings of your browser.
Detailed information about the configuration of the UTN server
can be found in the Online Help of the myUTN Control Center.
To start the Online Help, click the '?' icon.


16 [en] Quick Installation Guide

Quick Installation Guide [de] 17
2 Allgemeine Information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Verwendungszweck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Lieferumfang. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LED-Anzeige . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2 Sicherheitsvorschriften . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2 Hardware-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2 Software-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2 Erste Schritte mit dem SEH UTN Manager . . . . . . . . . 24
SEH UTN Manager starten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
UTN-Server eine IP-Adresse zuweisen . . . . . . . . . . . . . . . . . . . 26
UTN-Server der Auswahlliste hinzufügen . . . . . . . . . . . . . . . . 27
SD-Card-Reader und USB-Gerät mit Client verbinden . . . . 28
2 UTN-Server konfigurieren. . . . . . . . . . . . . . . . . . . . . . . . 29
 Inhaltsverzeichnis

18 [de] Quick Installation Guide
Allgemeine Information
Verwendungszweck
Der USB SDCardserver 'myUTN-120' ist ein netzwerkfähiger SD-Card-Reader.
Zudem erlaubt der myUTN-120 das Bereitstellen von einem nicht-
netzwerkfähigen USB-Gerät (z.B. Festplatte usw.) für mehrere
Netzwerkteilnehmer. Dazu wird das USB-Gerät an den USB-Port des myUTN-120
angeschlossen. Die Zugriffsverteilung des SD-Card-Readers und USB-Gerätes
erfolgt über das Software-Tool 'SEH UTN Manager'.
Der SEH UTN Manager wird auf alle Clients installiert, die auf den SD-Card-
Reader oder ein im Netzwerk bereitgestelltes USB-Gerät zugreifen sollen. Der
SEH UTN Manager zeigt die Verfügbarkeit aller in das Netzwerk eingebundenen
Geräte an und stellt die Verbindung zwischen Client und SD-Card-Reader bzw.
USB-Gerät her.
Die Verwaltung des myUTN-120 erfolgt über das 'myUTN Control Center'.
Lieferumfang
Bitte überprüfen Sie den Packungsinhalt auf Vollständigkeit, bevor Sie die
Installation beginnen:
UTN-Server USB SDCardserver 'myUTN-120'
Quick
Installation
Guide
Der Quick Installation Guide beinhaltet eine kurze
Beschreibung der Installation des myUTN-120.
(Dieses Dokument)
Netzteil Externes Netzteil

Quick Installation Guide [de] 19
Technische Daten
Eigenschaften Werte
Netzwerkanschluss Logisch:
Physisch: - IEEE 802.3
- RJ-45 (S/UTP Cat. 5)
Geräteanschluss - 1 x USB 2.0 HS
- 1 x SD-Card-Reader
SD-Card-Reader Kartentypen: - SD, SDHC
Stromaufnahme - 650 mA bei 5 VDC (ohne Last)
- 1150 mA bei 5 VDC (bei Volllast auf dem USB-Port)
Betriebsumgebung - Umgebungstemperatur: 5 - 40 °C
- Relative Luftfeuchtigkeit: 20 - 80 %
Abmessungen - Breite: 140 mm
- Höhe: 32 mm
- Tiefe: 99 mm
- Gewicht: 140 g
1) SD-Card-Reader
2) USB-Port
3) Link-LED (grün)
4) Activity-LED (gelb)
5) Status-LED (grün)
6) Power-LED (gelb)
7) LED für den SD-Card-Reader (grün/
orange)
8) LED für den USB-Port (grün/orange)
9) Netzwerkanschluss (RJ-45) für
1000BaseT, 100BaseTX und 10BaseT
10) Reset-Taster
11) Anschluss für die Stromversorgung
über das mitgelieferte Netzteil
Vorderansicht
Rückansicht

20 [de] Quick Installation Guide
LED-Anzeige
Durch die Interpretation des LED-Leuchtverhaltens kann der Zustand des UTN-
Servers ermittelt werden.
LED Aktion Farbe Beschreibung
Link Dauer-An
Dauer-Aus
grün
-
Eine Verbindung zum Netzwerk ist vorhanden.
Es besteht keine Verbindung zum Netzwerk.
Activity unregelmäßiges
Blinken gelb Signalisiert den Austausch von Netzwerk- Datenpaketen.
Status Dauer-Aus
3 x Blinken
2 x Blinken
-
grün
grün
Bei gleichzeitigem zyklischen Blinken der
Activity-LED wird der BIOS-Modus signalisiert.
Signalisiert die Vergabe einer ZeroConfig-IP-
Adresse.
Signalisiert die Vergabe einer IP-Adresse, die
nicht 0.0.0.0 entspricht oder aus dem Bereich
ZeroConfig kommt.
Power Dauer-An
Dauer-Aus
gelb
-
Das Gerät wird mit Strom versorgt.
Das Gerät wird nicht mit Strom versorgt.
SD-Card-
Reader Dauer-Aus
Dauer-An
Dauer-An
-
grün
orange
Es ist keine SD-Karte im Card-Reader
vorhanden.
Es ist eine SD-Karte im Card-Reader vorhanden.
Die SD-Karte im Card-Reader ist aktiviert.
USB-Port Dauer-Aus
Dauer-An
Dauer-An
-
grün
orange
Es ist kein USB-Gerät am Port angeschlossen.
Es ist ein USB-Gerät am Port angeschlossen.
Das USB-Gerät am Port ist aktiviert.