SEH myUTN-54 User manual

Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡[phone]
@[email protected]
USB Device Server
myUTN-54
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-54. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
UTN Server in the WLAN
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-54. Sie erhalten die folgenden
Informationen:
Allgemeine Information
Sicherheitsvorschriften
Hardware-Installation
Software-Installation
Erste Schritte
UTN-Server konfigurieren
UTN-Server im WLAN
Beachten Sie das Inhaltsverzeichnis auf
Seite 19. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support-
Hotline.

2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.

Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Scope of Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . . 9
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 11
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 12
Connecting the USB Device to the Client . . . . . . . . . . . . . . . . 13
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 14
2 UTN Server in the Wireless Network . . . . . . . . . . . . . . 15
Operating the UTN Server in the Wireless Network. . . . . . . 16
Connecting the UTN Server to the Wired Network . . . . . . . 16
 Table of Contents

4 [en] Quick Installation Guide
General Information
Purpose
The myUTN-54 allows you to access non-network-ready USB devices (e.g. hard
disks, etc.) in the network. For this purpose, the USB devices will be connected to
the USB ports of the myUTN-54. The software tool SEH UTN Manager handles the
access of the USB devices.
The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network. The SEH UTN Manager shows the availability of all USB
devices in the network and establishes a connection between the client and the
USB device.
Scope of Supply
Please check the package content before getting started:
UTN server USB Device Server (myUTN-54)
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-54.
(This document)
Power pack External power pack

Quick Installation Guide [en] 5
Technical Data
Properties Values
Device connection - 4 x USB 2.0 HS
Network connection logical:
physical:
- IEEE 802.3
- IEEE 802.11g
- IEEE 802.11b
- RJ-45 (STP Cat. 5)
- WLAN module
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity: 20 - 80 %
Dimensions - Length: 117 mm
- Width: 70 mm
- Height: 151 mm
- Weight: 220 g (+ 209 g power pack)
Current input - 350 mA @ 12 VDC (without load)
- 1650 mA @ 12 VDC (full load on the USB ports)
1) Reset button
2) Network connector (RJ-45)
for 100BaseTX and 10BaseT
3) USB Port 4
4) USB Port 3
5) USB Port 2
6) USB Port 1
7) Connector for the included
power pack.
8) Link LED (green)
9) Activity LED (yellow):
The LED indicates the
reception of data packets
from the network.
10) Status LED (green):
The LED indicates that the
device is operational.

6 [en] Quick Installation Guide
Safety Regulations
UTN servers are network devices for use in office environments. They are
designed for the integration of USB devices into networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
Warning! This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
The device must only be operated using the power pack included in the
package.
Do not remove or replace the WLAN module.
Observe the national restrictions which apply for the use of WLAN devices. For
more information, please consult your retailer.
Only use a certified USB Hi-Speed cable for the connection to the UTN server.
You will find a list of certified cables at www.usb.org.

Quick Installation Guide [en] 7
Hardware Installation
You can directly connect four USB devices to the UTN server (myUTN-54).
Clients with the software tool ’SEH UTN Manager‘
Proceed as follows:
1. Connect the UTN server and the USB device to the USB data
cable. (Repeat this step if you want to connect more than one
USB device.)
2. Connect the network cable (RJ-45) to the UTN server.
Note: Even if you want to use the UTN server in a WLAN you
must follow this step in order to carry out the initial
configuration of the UTN server.
3. Connect the power cord to the UTN server.

8 [en] Quick Installation Guide
Software Installation
The software tool ’SEH UTN Manager’ organizes the access of the USB devices.
The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service ’SEH UTN Service’. A detailed description can be found in the
myUTN User Manual.
Make sure that:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
First, you have to download the installation file for the SEH UTN Manager from
the homepage of SEH Computertechnik GmbH:
http://www.seh-technology.com/products/usb-device-servers/products/
myutn-54-downloads.html
Scan this QR code using your smart phone to get direct access to the homepage.
Proceed as follows:
1. Start the installation file.
2. Follow the installation routine.
The SEH UTN Manager is installed on your client.

Quick Installation Guide [en] 9
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected
devices – will be shown in the 'network list'. The preferred devices will be selected
and added to the 'selection list'. The devices in the selection list can be connected
to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 10
’Assigning an IP Address to the UTN Server’ 11
’Adding the UTN Server to the Selection List’ 12
’Connecting the USB Device to the Client’ 13
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a
secure UTN SSL port.
A detailed description can be found in the myUTN User
Manual.
Detailed information on how to use the SEH UTN Manager can be found
in the Online Help. To start the Online Help, select Help – Online Help
from the menu bar.


10 [en] Quick Installation Guide
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
During the initial configuration, client and UTN server must be assigned to the
same local network segment.

Quick Installation Guide [en] 11
Assigning an IP Address to the UTN Server
Once the UTN server is connected to the network, it checks whether an IP address
can be obtained from the boot protocols BOOTP or DHCP. If this is not the case,
the UTN server assigns itself an IP address via ZeroConf from the address range
(169.254.0.0/16) which is reserved for ZeroConf.
The UTN servers found by the program will be displayed in the network list. You can
change the TCP/IP parameters of the UTN server.
Proceed as follows:
1. Confirm the note dialog ’Your Selection List seems to be empty’ by clicking
Yes.
(If no note dialog is available and the main dialog appears, select Selection List – Edit
from the menu bar.)
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Select Set IP Address from the shortcut menu.
The Set IP Address dialog appears.
4. Enter the relevant TCP/IP parameters.
5. Click OK.
The settings are saved.

12 [en] Quick Installation Guide
Adding the UTN Server to the Selection List
In order to connect a UTN server to a client, you must assign the UTN server to
the selection list. Put together a selection list with your preferred UTN servers.
Proceed as follows:
1. Select Selection List – Edit from the menu bar.
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Click Add.
4. Click OK.
The UTN server is shown in the selection list.
You can extend the search for UTN servers to any network range. To do this, change the
search parameters for the network scan via the Options dialog in the Program menu.

Quick Installation Guide [en] 13
Connecting the USB Device to the Client
The USB devices in the selection list can be connected to the client.
Make sure that:
- All provisions (driver installation, etc.) necessary to operate the device locally
(i.e. connected directly to the client) have been met on the client. Ideally, the
device has been connected and operated on the client locally according to
the instructions of the manufacturer.
- The device is not connected to another client. A device that was made
available by the UTN server can only be used by one network participant at a
time.
Proceed as follows:
1. Mark the relevant USB device in the selection list.
2. Select Device – Activate from the menu bar.
The connection will be established.
Close the connection to the device when the device is no longer needed. Select
Device – Deactivate from the menu bar.

14 [en] Quick Installation Guide
Configuring the UTN Server
The UTN server can be configured and monitored via the ‘myUTN Control Center‘.
The myUTN Control Center is stored in the UTN server and can be launched by
means of a browser (Internet Explorer, Firefox, Safari).
Proceed as follows:
1. Open your browser.
2. Enter the IP address of the UTN server as the URL.
The myUTN Control Center appears in the browser.
If the myUTN Control Center is not displayed, check the proxy settings of your browser.
Detailed information about the configuration of the UTN server
can be found in the Online Help of the myUTN Control Center.
To start the Online Help, click the ‘?‘ icon.


Quick Installation Guide [en] 15
UTN Server in the Wireless Network
The UTN server model ’myUTN-54’ can handle WLAN. This allows you to wirelessly
operate the UTN server in the network.
In order to configure the UTN server you must first establish a connection to a wired
network by means of the network connector RJ-45.

16 [en] Quick Installation Guide
Operating the UTN Server in the Wireless Network
To operate the UTN server in a wireless network, the WLAN and security settings
of the UTN server must match those of the wireless network. A detailed
description can be found in the myUTN User Manual.
Proceed as follows:
1. Start the myUTN Control Center; see 14.
2. Select NETWORK - WLAN.
The available WLANs are shown in the network list.
3. Make sure that the WLAN parameters match those of the WLAN you want to
use. (By clicking the network name of the network that is displayed in the
list, you can easily copy a multitude of settings).
4. Tick WLAN to enable the WLAN module in the UTN server.
5. Click Save to confirm. The settings are saved.
6. Remove the network cable (RJ-45) from the UTN server.
The connection to the wired network will be deactivated.
The UTN server automatically switches to the WLAN mode.
The connection to the WLAN will be established.
If the UTN server gets a new IP address in the course of the network change, the
connection to the myUTN Control Center will be interrupted.
Connecting the UTN Server to the Wired Network
The following icons in the myUTN Control Center indicate the current connection
status:
To establish a connection to a wired network, connect the network
cable (RJ-45) to the UTN server. The UTN server automatically
switches to the wired network.
UTN server in the wireless network
UTN server in the wired network

Quick Installation Guide [en] 17

18 [en] Quick Installation Guide

Quick Installation Guide [de] 19
2 Allgemeine Information . . . . . . . . . . . . . . . . . . . . . . . . . 20
Verwendungszweck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lieferumfang. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2 Sicherheitsvorschriften . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2 Hardware-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2 Software-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2 Erste Schritte mit dem SEH UTN Manager . . . . . . . . . 25
SEH UTN Manager starten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
UTN-Server eine IP-Adresse zuweisen . . . . . . . . . . . . . . . . . . . 27
UTN-Server der Auswahlliste hinzufügen . . . . . . . . . . . . . . . . 28
USB-Gerät mit Client verbinden . . . . . . . . . . . . . . . . . . . . . . . . . 29
2 UTN-Server konfigurieren. . . . . . . . . . . . . . . . . . . . . . . . 30
2 UTN-Server im WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
UTN-Server im WLAN betreiben . . . . . . . . . . . . . . . . . . . . . . . . . 32
UTN-Server mit drahtgebundenen Netzwerk verbinden . 32
 Inhaltsverzeichnis

20 [de] Quick Installation Guide
Allgemeine Information
Verwendungszweck
Der myUTN-54 erlaubt das Bereitstellen von nicht-netzwerkfähigen USB-Geräten
(z.B. Festplatten usw.) für mehrere Netzwerkteilnehmer. Dazu werden die USB-
Geräte an die USB-Ports des myUTN-54 angeschlossen. Die Zugriffsverteilung der
USB-Geräte erfolgt über das Software-Tool ’SEH UTN Manager’.
Der SEH UTN Manager wird auf alle Clients installiert, die auf ein im Netzwerk
bereitgestelltes USB-Gerät zugreifen sollen. Der SEH UTN Manager zeigt die
Verfügbarkeit aller am Netzwerk eingebundenen USB-Geräte an und stellt die
Verbindung zwischen Client und USB-Gerät her.
Lieferumfang
Bitte überprüfen Sie den Packungsinhalt auf Vollständigkeit, bevor Sie die
Installation beginnen:
UTN-Server USB Device Server (myUTN-54)
Quick
Installation
Guide
Der Quick Installation Guide beinhaltet eine kurze
Beschreibung der Installation des myUTN-54.
(Dieses Dokument)
Netzteil Externes Netzteil