SEH myUTN-80 User manual

Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡[phone]
@[email protected]
USB Dongle Server
myUTN-80
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-80. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
Locking the UTN Server
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-80. Sie erhalten die folgenden
Informationen:
Allgemeine Information
Sicherheitsvorschriften
Hardware-Installation
Software-Installation
Erste Schritte
UTN-Server konfigurieren
UTN-Server abschließen
Beachten Sie das Inhaltsverzeichnis auf
Seite 19. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support-
Hotline.

2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.

Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Scope of Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . 10
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 12
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 13
Connecting the USB Dongle to the Client. . . . . . . . . . . . . . . . 14
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 15
2 Closing the UTN Server . . . . . . . . . . . . . . . . . . . . . . . . . . 16
 Table of Contents

4 [en] Quick Installation Guide
General Information
Purpose
The dongle server ‘myUTN-80‘ gives network participants access to USB dongles.
The USB dongles will be connected to the USB ports of the myUTN-80. The
software tool ’SEH UTN Manager’ handles the access to the USB dongles.
The SEH UTN Manager is installed on all clients that are intended to access a USB
dongle in the network. The SEH UTN Manager shows the availability of all USB
dongles in the network and establishes a connection between the client and the
USB dongle.
The lockable housing cover on the dongle server allows for a central and safe
storage of the USB dongles.
Scope of Supply
Please check the package content before getting started:
UTN server myUTN-80 Dongleserver
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-80.
(This document)
Power pack External power pack

Quick Installation Guide [en] 5
Technical Data
Properties Values
Device connection - 8 x USB 2.0 HS
Network connection logical:
physical: - IEEE 802.3
- RJ-45 (STP Cat. 5)
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity: 20 - 80 %
Dimensions - Length: 155 mm
- Width: 215 mm
- Height: 45 mm
- Weight: 1050 g with housing cover
Current input - 200 mA @ 12 VDC (without load)
- 2500 mA @ 12 VDC (full load on the USB ports)
1) Link LED (green)
2) Activity LED (yellow)
3) Status LED (green)
4) USB port 8
5) USB port 7
6) USB port 6
7) USB port 5
8) USB port 4
9) USB port 3
10) Reset button
11) USB port 2
12) USB port 1
13) LEDs for USB ports 1-8
14) Power LED
15) Connector for the
included power pack

6 [en] Quick Installation Guide
LED Display
The LEDs of the UTN server provide information about its status.
LED Action Color Description
Link permanently on green Indicates an existing connection to the network.
Activitiy blinks at
irregular
intervals
yellow Indicates the receipt of data packets.
Status permanently off
blinks 3 times
blinks 2 times
-
green
green
If the network activity LED blinks periodically at
the same time, the BIOS mode is signalized.
Indicates the assignment of a ZeroConfig IP
address.
Indicates the assignment of an IP address that
does not correspond to 0.0.0.0 or that comes
from outside the ZeroConf range.
USB Ports 1-8 permanently off
permanently on
permanently on
green
orange
Indicates that no USB dongle is connected to
the respective port.
Indicates that a USB dongle is connected to the
respective port.
Indicates that a USB dongle is enabled at the
respective port.

Quick Installation Guide [en] 7
Safety Regulations
UTN servers are network devices for use in office environments. The dongle server
is designed for the integration of USB dongles into networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
The device must only be operated using the power pack included in the
package.
Only use a certified USB Hi-Speed cable for the connection to the UTN server.
You will find a list of certified cables at www.usb.org.

8 [en] Quick Installation Guide
Hardware Installation
You can directly connect up to eight USB dongles to the UTN server (myUTN-80).
USB dongle and UTN server can be connected via a USB cable, if required. Please
only use USB cables shorter than 3 meters.
Clients with the software
tool ’SEH UTN Manager‘
Proceed as follows:
1. Connect the USB dongle to a USB port of the UTN server.
(Repeat this step if you want to connect more than one USB
dongle.)
2. Connect the network cable (RJ-45) to the UTN server.
3. Connect the power cord to the UTN server.

Quick Installation Guide [en] 9
Software Installation
The software tool ’SEH UTN Manager’ organizes the access of the USB dongles to
the USB devices. The SEH UTN Manager is installed on all clients that are
intended to access a USB dongle in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service ’SEH UTN Service’. A detailed description can be found in the
myUTN User Manual.
Make sure that:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
First, you have to download the installation file for the SEH UTN Manager from
the homepage of SEH Computertechnik GmbH:
http://www.seh-technology.com/products/usb-device-servers/products/
myutn-80-downloads.html
Scan this QR code using your smart phone to get direct access to the homepage.
Proceed as follows:
1. Start the installation file.
2. Follow the installation routine.
The SEH UTN Manager is installed on your client.

10 [en] Quick Installation Guide
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected USB
dongles – will be shown in the 'network list'. The preferred devices will be
selected and added to the 'selection list'. The USB dongles in the selection list can
then be connected to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 11
’Assigning an IP Address to the UTN Server’ 12
’Adding the UTN Server to the Selection List’ 13
’Connecting the USB Dongle to the Client’ 14
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a
secure UTN SSL port. A detailed description can be found in the myUTN User
Manual.
Detailed information on how to use the SEH UTN Manager can be found
in the Online Help. To start the Online Help, select Help – Online Help
from the menu bar.


Quick Installation Guide [en] 11
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
During the initial configuration, client and UTN server must be assigned to the
same local network segment.

12 [en] Quick Installation Guide
Assigning an IP Address to the UTN Server
Once the UTN server is connected to the network, it checks whether an IP address
can be obtained from the boot protocols BOOTP or DHCP. If this is not the case,
the UTN server assigns itself an IP address via ZeroConf from the address range
(169.254.0.0/16) which is reserved for ZeroConf.
The UTN servers found by the program will be displayed in the network list. You can
change the TCP/IP parameters of the UTN server.
Proceed as follows:
1. Confirm the note dialog ’Your Selection List seems to be empty’ by clicking
Yes.
(If no note dialog is available and the main dialog appears, select Selection List – Edit from the menu
bar.)
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Select Set IP Address from the shortcut menu.
The Set IP Address dialog appears.
4. Enter the relevant TCP/IP parameters.
5. Click OK.
The settings are saved.

Quick Installation Guide [en] 13
Adding the UTN Server to the Selection List
In order to connect a UTN server to a client, you must assign the UTN server to
the selection list. Put together a selection list with your preferred UTN servers.
Proceed as follows:
1. Select Selection List – Edit from the menu bar.
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Click Add.
4. Click OK.
The UTN server is shown in the selection list.
You can extend the search for UTN servers to any network range. To do this, change the
search parameters for the network scan via the Options dialog in the Program menu.

14 [en] Quick Installation Guide
Connecting the USB Dongle to the Client
The USB dongles in the selection list can be connected to the client.
Make sure that:
- All provisions necessary to operate the USB dongle locally (i.e. connected
directly to the client) should have been met on the client. Ideally, the USB
dongle has been connected and operated on the client locally according to
the instructions of the manufacturer.
- The USB dongle has not already been connected to another client. A USB
dongle that was made available by the UTN server can only be used by one
network participant at a time.
Proceed as follows:
1. Mark the relevant USB dongle in the selection list.
2. Select Device – Activate from the menu bar.
The connection will be established.
Close the connection to the USB dongle when the dongle is no longer needed.
Select Device – Deactivate from the menu bar.

Quick Installation Guide [en] 15
Configuring the UTN Server
The UTN server can be configured and monitored via the ‘myUTN Control Center‘.
The myUTN Control Center is stored in the UTN server and can be launched by
means of a browser (Internet Explorer, Firefox, Safari).
Proceed as follows:
1. Open your browser.
2. Enter the IP address of the UTN server as the URL.
The myUTN Control Center appears in the browser.
If the myUTN Control Center is not displayed, check the proxy settings of your browser.
Detailed information about the configuration of the UTN server
can be found in the Online Help of the myUTN Control Center.
To start the Online Help, click the ‘?‘ icon.


16 [en] Quick Installation Guide
Closing the UTN Server
The lockable housing cover on the dongle server allows for a central and safe
storage of the connected USB dongles.
To close the cover, insert the two straps of the housing cover into the notches of
the housing. Use the key provided to activate the locking mechanism.
We recommend using the Rack Mount Kit RMK1 for a perfect and safe storage of
the UTN server. Use the Rack Mount Kit to mount the UTN server myUTN-80 into
19" server racks. The RMK1 (Rack Mount Kit Type 1) is available as an accessory
upon request at SEH.

Quick Installation Guide [en] 17

18 [en] Quick Installation Guide

Quick Installation Guide [de] 19
2 Allgemeine Information . . . . . . . . . . . . . . . . . . . . . . . . . 20
Verwendungszweck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lieferumfang. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2 Sicherheitsvorschriften . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2 Hardware-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2 Software-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2 Erste Schritte mit dem SEH UTN Manager . . . . . . . . . 26
SEH UTN Manager starten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
UTN-Server eine IP-Adresse zuweisen . . . . . . . . . . . . . . . . . . . 28
UTN-Server der Auswahlliste hinzufügen . . . . . . . . . . . . . . . . 29
USB-Dongle mit Client verbinden . . . . . . . . . . . . . . . . . . . . . . . 30
2 UTN-Server konfigurieren. . . . . . . . . . . . . . . . . . . . . . . . 31
2 UTN-Server abschließen . . . . . . . . . . . . . . . . . . . . . . . . . 32
 Inhaltsverzeichnis

20 [de] Quick Installation Guide
Allgemeine Information
Verwendungszweck
Der Dongleserver ‘myUTN-80‘ stellt den Zugriff auf USB-Dongles mehreren
Netzwerkteilnehmern zur Verfügung. Dazu werden die USB-Dongles an den USB-
Ports des myUTN-80 angeschlossen. Die Zugriffsverteilung der USB-Dongles
erfolgt über das Software-Tool ’SEH UTN Manager’.
Der SEH UTN Manager wird auf alle Clients installiert, die auf einen im Netzwerk
bereitgestellten USB-Dongle zugreifen sollen. Der SEH UTN Manager zeigt die
Verfügbarkeit aller am Netzwerk eingebundenen USB-Dongles an und stellt die
Verbindung zwischen Client und USB-Dongle her.
Der abschließbare Gehäusedeckel am Dongleserver ermöglicht eine zentrale und
sichere Aufbewahrung der USB-Dongles.
Lieferumfang
Bitte überprüfen Sie den Packungsinhalt auf Vollständigkeit, bevor Sie die
Installation beginnen:
UTN-Server myUTN-80 Dongleserver
Quick
Installation
Guide
Der Quick Installation Guide beinhaltet eine kurze
Beschreibung der Installation des myUTN-80.
(Dieses Dokument)
Netzteil Externes Netzteil