SEH myUTN-50 User manual

Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡[phone]
@[email protected]
USB Device Server
myUTN-50
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-50. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-50. Sie erhalten die folgenden
Informationen.
Allgemeine Information
Sicherheitsvorschriften
Hardware Installation
Software Installation
Erste Schritte
UTN Server konfigurieren
Beachten Sie das Inhaltsverzeichnis auf
Seite 17. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support
Hotline.

2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.

Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . . 9
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 11
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 12
Connecting the USB Device to the Client . . . . . . . . . . . . . . . . 13
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 14
Configuring the UTN Server via the myUTN Control Center14
Configuring the UTN Server via the InterCon-NetTool. . . . 15
 Contents

4 [en] Quick Installation Guide
General Information
Purpose
The myUTN-50 allows you to access non-network-ready USB devices (e.g. hard
disks etc.) in the network. The USB devices will be connected to the USB port of
the myUTN-50. The software tool ’SEH UTN Manager’ regulates the access of the
USB devices.
The SEH UTN Manager is installed on all clients that are meant to access a USB
device in the network. The SEH UTN Manager shows the availability of all USB
devices that exist in the network and establishes a connection between the client
and the USB device.
Delivery
Please check the package content before getting started:
UTN Server USB Device Server (myUTN-50)
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-50.
(This document)
myUTN
Product CD The myUTN Product CD provides:
- User Manual (The pdf file provides a detailed
description of the myUTN administration.)
- SEH UTN Manager,
- InterCon-NetTool (Administration tool),
- SEH Private-MIB,
- Adobe Reader
Power Pack external power pack

Quick Installation Guide [en] 5
Technical Data
*The shield connection of the RJ45 connector is connected to the shield of the device port. This
connection must be taken into account when arranging your network cabling. For more
information, please consult your retailer.
Properties Values
Device Connection - 2 x USB 2.0 HS (may be extended to 5 ports)
Network Connection logical:
physical: - IEEE 802.3
- RJ-45 (STP Cat.5)
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity 20 - 80 %
Dimensions - Length 98 mm
- Width 81 mm
- Height 31 mm
- Weight 100 g
1) Link LED (green):
The link LED shows an existing connection to
the network.
2) Activity LED (yellow):
The LED indicates the reception of data
packets from the network.
3) Status LED (green):
The LED indicates that the device is
operational.
4) Reset button
5) Connector for the included power pack.
6) Network connector (RJ-45) for 100BaseTX and
10BaseT *
7) USB port 2 (may be extended using a USB hub)
8) USB port 1
9) Kensington security slot

6 [en] Quick Installation Guide
Safety Regulations
UTN servers are network devices for use in office environments. They are
designed for the integration of USB devices into networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
The device must only be operated using the power pack included in the
package.
Only use a certified USB Hi-Speed cable for the connection to the UTN server.
You will find a list of certified cables at www.usb.org.

Quick Installation Guide [en] 7
Hardware Installation
You can directly connect two USB devices to the UTN server (myUTN-50). If you use a
USB hub at the USB port 2, you can connect up to five USB devices.
No device with power supply solely via the USB port should be
connected to the UTN server.
Clients with software tool ’SEH UTN Manager’
Proceed as follows:
1. Connect the UTN server and the USB device to the USB data
cable. (Repeat this step if you want to connect more than one
USB device.)
2. Connect the network cable (RJ-45) to the UTN server.
3. Connect the power pack cable to the UTN server.

8 [en] Quick Installation Guide
Software Installation
The software tool ’SEH UTN Manager’ organizes the access of the USB devices.
The SEH UTN Manager is installed on all clients that are meant to access a USB
device in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service ’SEH UTN Service’. A detailed description can be found in the
myUTN User Manual.
Make sure the following points:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
Proceed as follows:
1. Start the myUTN Product CD on your Windows client.
2. Select the SEH UTN Manager installation file from the Tools menu.
3. Follow the installation routine.
The SEH UTN Manager is installed on your client.

Quick Installation Guide [en] 9
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected
devices – will be shown in the 'network list'. The preferred devices will be selected
and added to the 'selection list'. The devices in the selection list can be connected
to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 10
’Assigning an IP Address to the UTN Server’ 11
’Adding the UTN Server to the Selection List’ 12
’Connecting the USB Device to the Client’ 13
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a secure
UTN SSL port. A detailed description can be found in the myUTN User Manual.
Detailed information on how to use the SEH UTN Manager can be
found in the Online Help. To start the Online Help, select Help –
Online Help from the menu bar.


10 [en] Quick Installation Guide
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
When you start the program for the first time, you will be informed that there
are no UTN servers available in the ’selection list’. Add the UTN server to the
selection list.
During the initial configuration, client and UTN server must be assigned to the
same local network segment.

Quick Installation Guide [en] 11
Assigning an IP Address to the UTN Server
Once the UTN server is connected to the network, it checks whether an IP address
can be obtained from the boot protocols BOOTP or DHCP. If this is not the case,
the UTN server assigns itself an IP address via ZeroConf from the address range
(169.254.0.0/16) which is reserved for ZeroConf.
The UTN servers found by the program will be displayed in the ’network list’. You
can change the TCP/IP parameters of the UTN server.
Proceed as follows:
1. Confirm the note dialog ’Your Selection List seems to be empty’ by clicking
Yes. (If no note dialog is available and the main dialog appears, select
Selection List – Edit from the menu bar.)
The Edit Selection List dialog appears.
2. Mark the UTN server from the Network List.
3. Select Set IP Address from the context menu.
The Set IP Address dialog appears.
4. Enter the relevant TCP/IP parameters.
5. Click OK.
The settings are saved.

12 [en] Quick Installation Guide
Adding the UTN Server to the Selection List
In order to connect a UTN server to a client, you must assign the UTN server to
the ’selection list’. Put together a selection list with your preferred UTN servers.
Proceed as follows:
1. Select Selection List – Edit from the menu bar.
The Edit Selection List dialog appears.
2. Select the UTN server from the network list.
3. Click Add.
4. Click OK.
The UTN servers are shown in the selection list.
You can extend the search for UTN servers to any network range. To do this,
change the search parameters for the network scan via the Options dialog.


Quick Installation Guide [en] 13
Connecting the USB Device to the Client
The USB devices in the selection list can be connected to the client.
Make sure the following points:
- All provisions (driver installation etc.) necessary to operate the device locally
(i.e. connected directly to the client) should have been met on the client.
Ideally, the device has been connected and operated on the client locally
according to the instructions of the manufacturer.
- The device is not connected to another client. A device that was made
available by the UTN server can only be used by one network participant at a
time.
Proceed as follows:
1. Mark the relevant USB device in the selection list.
2. Select Device – Activate from the menu bar.
The connection will be established.
Close the connection to the device when the device is no longer needed. Select
Device – Deactivate from the menu bar.

14 [en] Quick Installation Guide
Configuring the UTN Server
Configuring the UTN Server via the myUTN Control Center
The UTN server can be configured and monitored via the myUTN Control Center.
The myUTN Control Center is stored in the UTN server and can be started by
means of an Internet browser (Internet Explorer, Netscape, Firefox, Safari).
Proceed as follows:
1. Open your browser
2. Enter the IP address of the UTN server as URL.
The myUTN Control Center is displayed in the browser. If the myUTN Control
Center is not displayed, check the proxy settings of your browser.
Detailed information about the configuration of the UTN server
can be found in the Online Help of the myUTN Control Center.
To start the Online Help, click the ‘?‘ icon.


Quick Installation Guide [en] 15
Configuring the UTN Server via the InterCon-NetTool
The software InterCon-NetTool has been developed by SEH Computertechnik
GmbH for the administration of SEH network devices. You can configure the
following features via the InterCon-NetTool.
Configuring TCP/IP Parameter (IPv4)
Resetting parameters (factory default setting)
Restarting the device
Starting the myUTN Control Center
Switching from the BIOS mode into the standard mode
Proceed as follows:
1. Start the myUTN Product CD on the Windows Client
2. Select Tools - InterCon-NetTool.
3. Start the InterCon-NetTool installation file.
4. Follow the installation routine.
The InterCon-NetTool will be installed to your system.
Start the InterCon-NetTool on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> InterCon-NetTool)
Detailed information on how to use the InterCon-NetTool can be found
in the Online Help. To start the Online Help, select Help – Online Help
from the menu bar.


16 [en] Quick Installation Guide

Quick Installation Guide [de] 17
2 Allgemeine Information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Verwendungszweck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Lieferumfang. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2 Sicherheitsvorschriften . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2 Erste Schritte mit dem SEH UTN Manager . . . . . . . . . 23
SEH UTN Manager starten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
UTN Server eine IP-Adresse zuweisen . . . . . . . . . . . . . . . . . . . 25
UTN Server der Auswahlliste hinzufügen . . . . . . . . . . . . . . . . 26
USB-Gerät mit Client verbinden . . . . . . . . . . . . . . . . . . . . . . . . . 27
2 UTN Server konfigurieren . . . . . . . . . . . . . . . . . . . . . . . . 28
UTN Server via myUTN Control Center konfigurieren. . . . . 28
UTN Server via InterCon-NetTool konfigurieren. . . . . . . . . . 29
 Inhaltsverzeichnis

18 [de] Quick Installation Guide
Allgemeine Information
Verwendungszweck
Das myUTN-50 erlaubt das Bereitstellen von nicht-netzwerkfähigen USB-Geräten
(z.B. Festplatten, usw.) für mehrere Netzwerkteilnehmer. Dazu werden die USB-
Geräte an den USB-Port des myUTN-50 angeschlossen. Die Zugriffsverteilung der
USB-Geräte erfolgt über das Software Tool ’SEH UTN Manager’.
Der SEH UTN Manager wird auf alle Clients installiert, die auf ein im Netzwerk
bereitgestelltes USB-Gerät zugreifen sollen. Der SEH UTN Manager zeigt die
Verfügbarkeit aller am Netzwerk eingebundenen USB-Geräte an und stellt die
Verbindung zwischen Client und USB-Gerät her.
Lieferumfang
Bitte überprüfen Sie den Packungsinhalt auf Vollständigkeit, bevor Sie die
Installation beginnen:
UTN Server USB Device Server (myUTN-50)
Quick
Installation
Guide
Der Quick Installation Guide beinhaltet eine kurze
Beschreibung der Installation des myUTN-50.
(Dieses Dokument)
myUTN
Product CD Die myUTN Product CD beinhaltet:
- Benutzerdokumentation
(Die pdf-Datei beinhaltet eine detaillierte
Beschreibung der myUTN Administration.)
- SEH UTN Manager,
- InterCon-NetTool (Administration Tool),
- SEH Private-MIB,
- Adobe Reader
Netzteil Externes Netzteil

Quick Installation Guide [de] 19
Technische Daten
* Der Schirmanschluss des RJ45-Netzwerk-Steckverbinders ist mit dem Schirm des Geräte-
anschlusses verbunden. Diese Verbindung muss bei Ihrer Netzwerkverkabelung berücksichtigt
werden. Fragen Sie hierzu Ihren Fachhändler.
Eigenschaften Werte
Geräteanschluss - 2 x USB 2.0 HS (erweiterbar auf 5 Anschlüsse)
Netzwerkanschluss Logisch:
Physikalisch: - IEEE 802.3
- RJ-45 (STP Cat.5)
Betriebsumgebung - Umgebungstemperatur: 5 - 40 °C
- Relative Luftfeuchtigkeit: 20 - 80 %
Abmessungen - Länge 98 mm
- Breite 81 mm
- Höhe 31 mm
- Gewicht 100 g
1) Link-LED (grün):
Die LED signalisiert eine vorhandene
Verbindung zum Netzwerk.
2) Netzwerkaktivität-LED (gelb):
Die LED signalisiert den Empfang von
Datenpaketen aus dem Netzwerk.
3) Status-LED (grün):
Die LED signalisiert die Betriebsbereitschaft
des Gerätes.
4) Reset-Taste
5) Anschluss für die Stromversorgung über das
mitgelieferte Netzteil.
6) Netzwerkanschluss (RJ-45) für 100BaseTX und
10BaseT *
7) USB Anschluss 2 (erweiterbar durch USB Hub)
8) USB Anschluss 1
9) Schlitz für Kensington Verriegelung

20 [de] Quick Installation Guide
Sicherheitsvorschriften
UTN Server sind Netzwerkgeräte für den Gebrauch in Büroumgebungen. Sie
dienen dem Einbinden von USB-Geräten in Netzwerken.
Beachten Sie vor Inbetriebnahme und beim Betrieb des UTN Server die folgenden
Sicherheitsvorschriften, um sich und andere vor Personenschäden zu schützen
sowie Beschädigungen am Gerät zu vermeiden.
Lesen Sie die Dokumentation und stellen Sie sicher, dass Ihr System den
aufgeführten Anforderungen entspricht.
Das Gerät darf nicht mit Feuchtigkeit oder Flüssigkeiten in Berührung
kommen.
Das Gerät darf nur in unversehrtem Zustand angeschlossen und betrieben
werden.
Verlegen Sie alle Kabel so, dass niemand darauf treten oder darüber stolpern
kann.
Schließen Sie keine Telefonleitungen an dem RJ-45 Stecker an. An diesen darf
nur Sicherheitskleinspannung angeschlossen werden. Verwenden Sie für den
Anschluss an den RJ-45 Stecker nur STP-Kabel (Kategorie 5 oder besser).
Kabelschirm und Steckerschirm des Kabels müssen flächig verbunden sein.
Das Gerät darf nur mit dem mitgelieferten Netzteil betrieben werden.
Verwenden Sie für die Verbindung zum UTN Server ein zertifiziertes USB-Hi-
Speed-Kabel. Eine Liste der zertifizierten Kabel finden Sie unter www.usb.org.