Seville Classics UltraHD 20235 User manual

SC210823
ASSEMBLY INSTRUCTIONS
UltraHD® 3-Drawer Rolling Cabinet (Model No. 20235)
28 in. W x 18 in. D x 34.5 in. H
(71.1 cm x 45.7 cm x 87.6 cm)
Reference page 12 for special care and
maintenance of stainless steel
Granite

1

2
PARTS LIST
(#7) BOTTOM PANEL X 1PC (#24)FRONT FRAME CONNECTION CROSSBAR X 1PC
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 13 of 14).
(#5) RIGHT PANEL X 1PC (#6) FRONT FRAME X 1PC
(#1) SOLID HARDWOOD TOP X 1PC (#2) UPPER BACK PANEL X 1PC
(#3) BOTTOM BACK PANEL X 1PC (#4) LEFT PANEL X 1PC

(#20-5)SMALL DRAWER BACK PANEL X 3PCS (#20-4) SMALL DRAWER RIGHT PANEL X 3PCS
(#19-2) DRAWER BASE PANEL X 3PCS (#18) DRAWER MAT x 3 PCS
(#20-1) SMALL DRAWER FRONT PANEL X 3PCS (#20-3) SMALL DRAWER LEFT PANEL X 3PCS
(#20-A)LEFT DOOR X 1PC (#20-B)RIGHT DOOR X 1PC
3
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 13 of 14).

(#17) SCREW D (M8 x 18) x 16 PCS (#16) SCREW C (M4 x 18) x 16 PCS
(#12) SWIVEL WHEEL WITH BRAKE x 2 PCS (#13) SWIVEL WHEEL W/O BRAKE x 2 PCS
(#10) PUSH BAR x 1 PC (#11) BUMPER x 4 PCS
(#9) LEFT BACK CORNER PROTECTOR X 1PC (#8) RIGHT BACK CORNER PROTECTOR X 1PC
4
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 13 of 14).

5
(#23)MAGNET X 1PC
(#22)DOOR / DRAWER KEY x 4PCS (#21) SCREWDRIVER x 1PC
(#14) SCREW A (M4 x 10) x 57 PCS (#15) SCREW B (M4 x 8) x 69 PCS
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please
contact our customer service department (please refer to page 13 of 14).

TIP:
Step 1.
Step 2.
Note:
Step 3.
Note:
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.
A magnetic screwdriver is included for your
convenience. If using a powered driver, keep
torque setting on LOW.
Open the package, remove and place all parts to the
side. Then open the package of the Solid Hardwood
Top (#1).
Note: The Solid hardwood Top is packed within an
inner cardboard box.
Install Front Frame (#6)
Locate the Front Frame (#6) and attach to the
"Front" of the Solid Hardwood Top (#1), using 3 pcs
Screw A (#14) and Screwdriver (#21) to tighten.
1.Make sure that the top and sides of the Front
Frame are flush with the Solid Hardwood Top (#1)
2.Don't tighten screws completely. Line up screw
holes then to tighten after installing side panels.
Install the Left Panel (#4)
a.) Remove 2 pcs Sliders to create the space needed
to use the screwdriver (#21). Then, attach the Left
Panel (#4) to the Front Frame (#6) and the Solid
Hardwood Top (#1). Make sure the “Top” of the
Left Panel (#4) is on the Solid Hardwood Top (#1)
and the screw holes are lined up to the Front Frame
(#6). Use Screwdriver (#21) and 6 pcs Screw A (#14)
to tighten the Left Panel (#4) to the Front Frame
(#6), and then to Solid Hardwood Top (#1).
Don't tighten screws completely which on Solid
Hardwood Top.
b.) Re-install the removed 2 pcs Sliders to the
Left Panel (#4).
Front
Back
Front
Back
Remove 2pcs Slides to create the space needed
to use the Screwdriver (#21).
#1
#14
#4
#14
#6
#14
#4
#4
#4
6

Step 4.
Note:
Step 5.
Step 6.
Repeat Step 3,install the Right Panel (#5)
Attach Front Frame (#6), Left Panel (#4), Right
Panel (#5) onto the bottom edge of Solid
Hardwood Top (#1). Line up the screw
holes and tighten.
Install the Bottom Panel (#7)
Attach the Bottom Panel (#7) to the Left Panel
(#4), Right Panel (#5), Front Frame (#6),
Bottom Back Panel (#3), line up screw holes
and use 7 pcs Screw A (#14) to tighten.
Install the Upper Back Panel (#2) and Bottom
Back Panel (#3).
Install the Right Panel (#5).
a. Attach the Upper Back Panel (#2) between
the Left Panel (#4) and Right Panel (#5).
Make sure the “Top” of the Upper Back Panel
(#2) is on the Solid Wood Top (#1) as the sticker
indicates. Line up the screw holes and use
Screw A (#14) to tighten up the Upper Back
Panel to the Solid Wood Top (#1), Left Panel
(#4) and Right Panel (#5).
b. Attach Bottom Back Panel (#3) between the
Left Panel (#4) and Right Panel (#5).
Make sure the “Top” of the Bottom Back Panel
(#3) is to the Upper Back Panel (#2) as the
sticker indicates. Line up the screw holes and
use Screw A (#14) to tighten the Bottom Back
Panel (#3) to the Upper Back Panel (#2),
Left Panel (#4) and Right Panel (#5).
Front
#14
#3
#2
#5
#7
#14
7
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

Step 7.
Step 8.
Step 9.
Attach Right Back Corner Protector (#8) to the
top of right back side, and attach Left Back
Corner Protector to the top of left side, using
10 pcs Screws A (#14) to tighten.
Attach Wheels (#12 and #13) to the Bottom
Panel (#7) and surrounding frame.
Make sure the Swivel Wheels with Brake are
installed at the front side.
Use Screws D (#17) to tighten.
Attach Bumpers (#11) to the bottom four
corners of the cabinet. Use Screw C (#16) to
tighten them.
Install Right Back Corner Protector (#8)
and Left Back Corner Protector (#9)
Install Wheels (#12 and #13).
Install Bumpers (#11).
#12
#12
#13
#13
#17
#14
#8
8
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

Step 10.
Note:
Step 11.
Note:
Install Front frame connection crossbar (#24).
Attach the front frame connection crossbar (#24) on
the middle of the front frame (#6).
Use 4pcs Screw A (#14) to tighten them.
The small round hole faces the outside when
Installing, as show by the arrow on the left.
Install Small Drawers (#20)
a.) Install Small Drawers Front Panel (#20-1), Small
Drawer Left Panel (#20-3), Small Drawer Right Panel
(#20-4). Put one side of Small Drawer Left Panel
(#20-3) onto the Small Drawers Front Panel (#20-1)
as left picture. Use 1pcs Screws B (#15) to tighten.
Repeat Step 11 to install Small Drawer Right Panel
(#20-4).
b.) Install Small Drawer Base Panel (#19-2)
From above, fit and attach Small Drawer Base Panel
(#19-2) between the two sides. Line up the screw
holes to the Drawer Base Panel (#19-2) and Small
Drawers Front Panel (#20-1).Use 4pcs Screws B
(#15) to tighten. Finally use 6pcs Screws B (#15) to
tighten the two sides of Drawer Base Panel (#19-2)
and left & right side panel.
c.) Install Small Drawer Back Panel (#20-5)
Attach the Small Drawer Back Panel (#20-5) to the
Small Drawer Base Panel (#19-2) and Small Drawer
Left Panel (#20-3) and Small Drawer Right
Panel(#20-4). Use 5pcs Screws B (#15) to tighten
them.
#6
9
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

Step 12. Install Drawers (#20) into Cabinet
`
Step 13. Install Magnet. (#23)
Note:
a.) As shown by the left picture, pull out
both slides rail to the farthest.
Note: slides can be pulled out which the key
rod is in the open state, because the cabinet
has an interlocking function, only one pair of
slides can be pulled out at a time.
b.) Hook the drawer between both slides,
make sure the slides hooks are insert into
the square holes on the drawer side panels
completely.
c.) Line up the screw holes, and using 4 pcs
Screw B (#15) to tighten the drawer.
Place Magnet (#23) onto Bottom of Front
Frame (#6). Use 2pcs (#14) Screw F to tighten.
The side of the magnet with the black sponge
pad facing outward.
#14
#15
10
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

Step 14.
Note:
Step 15.
Step 16.
`
Place Drawer Mat (#18) into Drawers
Attach the Left Door (#20-A) to the left side
of the door frame and Right Door (#20-B) to
the right side of the door frame. Use 6 pcs
Screw B (#15) to tighten.
Install the Left Door (#20-A) and Right Door
Attach Push Bar (#10) to the top of cabinet,
using 8 pcs Screw A (#14) to tighten.
Install Push Bar (#10).
Place a mat(#18) for each drawer.
The elliptical hole on the door hinge can
adjust up and down gap of the door.
11
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

How to remove drawer
1. First pull out the small drawer and press down the positioning block on the right side of the drawer by hand, and press the fixed pull block
on the left up to take out the drawer. You can also unscrew the 4pcs screws on the side of the drawer to make the whole drawer up.
2. When taking the second drawer, you need to manually press the interlock lever to close the interlock function, repeat the above method
1 to take out the drawer.
3. Repeat the steps 1-2 above to take out the drawer.
Press the interlock lever down
Pull up
Push down
Stainless Steel Maintenance:
These parts have an UltraGuard® fingerprint
resistant finish. Do not use traditional
stainless steel cleaners on this unit. Lightly
wipe off once a month with clean warm water
and a soft cloth (preferably a micro fiber
cloth). This is the safest formula to prevent
new stains from appearing over time and
manage unwanted fingerprints or grease
marks. Remember to always wipe in the
direction of the surface grain (NEVER ACROSS)
and always use a lint-free cloth. Once the
surface is clean,thoroughly wipe dry with a
soft absorbent cloth.
12
UltraHD® 3-Drawer Rolling Cabinet (Model No. UHD20235)
*NOTE: We recommend using TWO people to assemble the cabinet.

Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: [email protected]
Website & Online Store: www.sevilleclassics.com
UltraHD® Tall Storage Cabinet UltraHD® Mega Storage Cabinet
Model No. 16236 (Granite) Model No. 16238 (Granite)
Model No. 20143 (Graphite)
Model No. 20148 (Graphite)
Model No. 20153 (Red) Model No. 20158 (Red)
Model No. 20133 (White)
CONTACT INFORMATION
If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our
bilingual (English and Spanish) customer service department at:
***Please visit our website or call and inquire about our additional UltraHD Line***
UltraHD® Line
13

UltraHD® 4-Drawer Rolling Cabinet UltraHD® 6-Foot Height Adjustable Workbench
Model No. 20205 (Granite) Model No. 20292 (Granite)
UltraHD® Wall Cabinet with Open Shelf UltraHD® 2-Door Rolling Workbench
Model No. 20230 (Granite) Model No. 20262 (Granite)
Model No. 20140 (Graphite)
Model No. 20142 (Graphite)
Model No. 20150 (Red) Model No. 20152 (Red)
UltraHD® Rolling Trash Bin UltraHD® Lighted Workcenter
Model No. 20215 Model No. 20247 (Granite)
Model No. 20246 (Graphite)
Model No. 20157 (Red)
UltraHD® Line