ShoreStation SSV30108EDC User manual

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 1 REV B 6/24/2008
SSV30108EDC & SSV30108EDCDW
SSV30108EDC Hoist Alum SS V-Frame - EDC
69426 Hardware Box - SSV30108 Hoist
62504 Lower Frame Bundle - V30108
62864 Platform Bundle - V30108
6941401 Winch Assembly - DC 1500 & 3000 lb Hoist
65021 Winch Tube Bundle - V30108
62927 Leg Bundle - V30108
HA0024 Motor Stop Bundle Alum 5” V-Frame
HA0053 Bunk Poly V30/40108 & 30/40120
HA0061 Battery Box / Brkt Mech. Winch Tube
69588 Lit Packet, V30108EDC/DW
NOTE: When referencing the front of hoist, this represents the winch end. When referencing the hoist end, this represents opposite of the
winch end. Winch side is also referred to the right side of the hoist.
SSV30108EDCDW Hoist Alum SS V-Frame - EDCDW
69426 Hardware Box - SSV30108 Hoist
62504 Lower Frame Bundle - V30108
62864 Platform Bundle - V30108
6941401 Winch Assembly - DC 1500 & 3000 lb Hoist
65021 Winch Tube Bundle - V30108
67227 Leg Bundle - V30108/120-40108/120
HA0024 Motor Stop Bundle Alum 5” V-Frame
HA0053 Bunk Poly V30/40108 & 30/40120
HA0061 Battery Box / Brkt Mech. Winch Tube
69588 Lit Packet, V30108EDC/DW

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 2 REV B 6/24/2008

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 3 REV B 6/24/2008

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 4 REV B 6/24/2008

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 5 REV B 6/24/2008

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 6 REV B 6/24/2008

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 7 REV B 6/24/2008
Winch Post Guide Posts
Lower Frame Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 8 REV B 6/24/2008
Platform Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 9 REV B 6/24/2008
Winch Tube Assembly
WINCH TUBE SERVICE INSTRUCTIONS
The winch tube assembly was pre-assembled at the factory.
It is important that the internal parts and cable routings are
assembled properly in order for the winch tube assembly to
function properly. It also requires special tools during the as-
sembly process. It is therefore recommended that you con-
tact your local dealer should you ever have issues with the
winch tube assembly.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 10 REV B 6/24/2008
Detail A
Detail A
DC Drive Winch Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 11 REV B 6/24/2008
Battery Box

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 12 REV B 6/24/2008
Motor Stop Assembly
Adjustment
Position the hoist motor stop assembly on the hoist so it
is centered side to side on the hoist platform. Changing
the motor stop location front to rear is accomplished by
sliding the straight portion of the motor stop arm through
the U-bolts. This allows you to change the motor stop
location to best position your boat on the hoist. Once the
assembly is in the proper position, tighten the nuts on the
U-bolts.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 13 REV B 6/24/2008
DW (Deep Water) SECTION:
The deep water version of this boat hoist is assembled
using the same assembly instructions as the standard
hoist. The only items that are different between the two
hoists are the length of the upright corner posts and the
adjustable legs inside them as identied in the drawings
for deep water legs.
The water depth where your hoist is going to be installed
will determine whether you should use the deep water
version of this hoist.
The deep water version of this hoist can be used in deep-
er water depths because of the additional length of the
extension legs. Listed below is the amount of adjustment
the various legs have.
• A standard leg shipped with the hoist has 20” of
adjustment.
• The deep water legs have 55” of adjustment.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 14 REV B 6/24/2008
1/2” x 4”HH Bolt Qty: 1 (0110114)
3/8” x 6”HH Bolt Qty: 4 (0110068)
3/8” x 5-1/2”HH Bolt Qty:12 (0110066)
3/8” x 3-3/4”HH Bolt Qty:8 (0110059)
3/8” x 1-1/2”HH Bolt Qty:13 (0140045)
5/16”x 3/4”HH Bolt
Qty: 16 (0140022)
3/8” x 3/4”Carriage Bolt
Qty: 8 (0210100)
5/8” Brass Hex Nut
Qty: 10 (1410362)
5/8”Flat Washer
Qty: 6 (1340105)
#7 Hitch Pin Clip
Qty: 4 (1540300)
5/16”Flat Washer
Qty: 16 (1310085)
5/16”Lock Washer
Qty: 16 (1310025)
5/16”Hex Nut
Qty: 16 (1410069)
3/8” Flat Washer
Qty: 37 (1340095)
3/8”Flange Lock Nut
Qty: 45 (1440101)
1/2” Flange Lock Nut
Qty: 1 (1440102)
1/2” Flat Washer
Qty: 1 (1340100)
0160054 Pre-Packaged Hardware Bag

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003784
PAGE 32 REV B 6/24/2008
4850408
Not A Step Decal
4811312
Clamp Arrow Decal
4811319
Adj. Guage Decal
4811503
Max Load
Decal - Winch
Assembly 4850363
Safety Decal
4811312
Clamp Arrow Decal
4811319
Adj. Gauge Decal
4811502
Safety Operating Decal
4850408
Not A Step Decal
SSV30108EDC Decal Placement
4811503 Maximum Load Decal - Winch Assy
4811502 Safety Operating Decal
4811312 Clamp Arrow Decal
4811319 Adj. Gauge Decal
4850363 Safety Decal
4850408 Not A Step Decal