ShoreStation SSV30120EAC User manual

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 1 REV C 03/11/2009
SSV30120EAC & SSV30120EACDW
SSV30120EAC Hoist Alum SS V-Frame - EAC
69426 Hardware Box - SSV30/40120 Hoist
63401 Lower Frame Bundle - SSV30/40120
63402 Platform Bundle - SSV30/40120
6941301 Winch Assembly - AC - V15/V30
65021 Winch Tube Bundle - SSV30/40120
62927 Leg Bundle - SSV30/40120
HA0024 Motor Stop Bundle Alum 5” V-Frame
HA0053 Bunk Poly V30/V40108 / V30/40120
69590 Lit Packet, V30120EAC/DW
NOTE: When referencing the front of hoist, this represents the winch end. When referencing the hoist end, this represents opposite of the
winch end. Which side is also referred to the right side of the hoist.
SSV30120EAC DW Hoist Alum SS V-Frame - EAC
69426 Hardware Box - SSV30/40120 Hoist
63401 Lower Frame Bundle - SSV30/40120
63402 Platform Bundle - SSV30/40120
6941301 Winch Assembly - AC - V15/V30
65021 Winch Tube Bundle - SSV30/40120
67227 Leg Bundle - V30/40120 DW
HA0024 Motor Stop Bundle Alum 5” V-Frame
HA0053 Bunk Poly V30/V40108 / V30/40120
69590 Lit Packet, V30120EAC/DW

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 2 REV C 03/11/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 3 REV C 03/11/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 4 REV C 03/11/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 5 REV C 03/11/2009

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 6 REV C 03/11/2009
Winch Post
Guide Post
Lower Frame Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 7 REV C 03/11/2009
Platform Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 8 REV C 03/11/2009
Winch Tube WINCH TUBE SERVICE INSTRUCTIONS
The winch tube assembly was pre-assembled at the factory.
It is important that the internal parts and cable routings are
assembled properly in order for the winch tube assembly to
function properly. It also requires special tools during the as-
sembly process. It is therefore recommended that you con-
tact your local dealer should you ever have issues with the
winch tube assembly.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 9 REV C 03/11/2009
Bunk Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 10 REV C 03/11/2009
Detail A
See Detail A
AC Drive Winch Assembly

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 11 REV C 03/11/2009
HA0024 - Motor Stop
Adjustment
Position the hoist motor stop assembly on the hoist so it
is centered side to side on the hoist platform. Changing
the motor stop location front to rear is accomplished by
sliding the straight portion of the motor stop arm through
the U-bolts. This allows you to change the motor stop
location to best position your boat on the hoist. Once the
assembly is in the proper position, tighten the nuts on the
U-bolts.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 12 REV C 03/11/2009
DW (Deep Water) SECTION:
The deep water version of this boat hoist is assembled using
the same assembly instructions as the standard hoist. The
only items that are different between the two hoists are the
length of the upright corner posts and the adjustable legs in-
side them as identied in the drawings for deep water legs.
The water depth where your hoist is going to be installed will
determine whether you should use the deep water version
of this hoist.
The deep water version of this hoist can be used in deeper
water depths because of the additional length of the exten-
sion legs. Listed below is the amount of adjustment the vari-
ous legs have.
• A standard leg shipped with the hoist has 20” of
adjustment.
• The deep water legs have 55” of adjustment.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 13 REV C 03/11/2009
1/2” x 4”HH Bolt Qty: 1 (0110114)
3/8” x 6”HH Bolt Qty: 4 (0110068)
3/8” x 5-1/2”HH Bolt Qty:12 (0110066)
3/8” x 3-3/4”HH Bolt Qty:8 (0110059)
3/8” x 1-1/2”HH Bolt Qty:13 (0140045)
5/16”x 3/4”HH Bolt
Qty: 16 (0140022)
3/8” x 3/4”Carriage Bolt
Qty: 8 (0210100)
5/8” Brass Hex Nut
Qty: 10 (1410362)
5/8”Flat Washer
Qty: 6 (1340105)
#7 Hitch Pin Clip
Qty: 4 (1540300)
5/16”Flat Washer
Qty: 16 (1310085)
5/16”Lock Washer
Qty: 16 (1310025)
5/16”Hex Nut
Qty: 16 (1410069)
3/8” Flat Washer
Qty: 37 (1340095)
3/8”Flange Lock Nut
Qty: 45 (1440101)
1/2” Flange Lock Nut
Qty: 1 (1440102)
1/2” Flat Washer
Qty: 1 (1340100)
0160054 Pre-Packaged Hardware Bag

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003780
PAGE 29 REV C 03/11/2009
4850408
Not A Step Decal
4811312
Clamp Arrow Decal
4811319
Adj. Guage Decal
4811503
Max Load
Decal
4850363
Safety Decal
4811312
Clamp Arrow Decal
4811319
Adj. Gauge Decal
4811502
Safety Operating Decal
4850408
Not A Step Decal
SSV30120EAC Decal Placement
4811503 Maximum Load Decal - Winch Assy
4811502 Safety Operating Decal
4811312 Clamp Arrow Decal
4811319 Adj. Gauge Decal
4850363 Safety Decal
4850408 Not A Step Decal