ShowPro ProShop LED PAR Hex-7 User manual

LED PAR Hex-7
1
User Manual
LED PAR Hex-7
www.showtech.com.au

LED PAR Hex-7
2
Table of Contents
1. Safety instructions…………………………………………………………3
1.1 Overhead rigging …………………………………………………….4
1.2 Power Connection …………………………………………………..6
1.3 Cleaning and Maintenance ……………………………………..6
2. Menu Navigation ............................................................7
3. DMX Allocation ...............................................................12
4. Technical Specifications ..................................................15

LED PAR Hex-7
3
1. Safety Instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperature.
Avoid exposing it to direct rays of sun near a heating appliance.
Do not put it in a temperature below 41°F/5°C, or exceeding 95°F/35°C.
Keep away from humidity, water and dust.
Do not place the set in a location with a high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
NO USER SERVICABLE PARTS INSIDE.
If unit is out of service please contact your point of purchase.
If any troubles arise, remove the power plug and contact your Pro Shop
representative for repair. Do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable. Never pull the power cable to remove the plug from
the receptacle, be sure to hold the plug.

LED PAR Hex-7
4
When not using the unit for an extended period of time be sure to disconnect the
plug form the receptacle.
1.1. OverheadRigging
This item must be built in a way that it can hold 10 times more of its weight for 1
hour without causing any damages. The installation must be secured with a
secondary safety attachment. The Safety attachment has to be constructed in a way
that no part of the installation can fall down. When rigging, de-rigging or servicing
the fixture staying in the area below the installation place, on bridges, under high
working places and other endangered areas us forbidden. Before taking the device in
operation, the installation must be approved by an expert. The operator has to make
sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE.
Including (but not limited to) calculating working load limits, installation material
being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installations yourself,
but instead use a professional structural rigger. Improper installation can result in
bodily injury and/or damage to property.
IMPORTANT:
If multiple PixPadpanels are being rigged together as a larger system, special care
must be taken to ensure total loads are adhered to. A maximum of 10 panels should
be hung under each other, longer drops require further bracing or load support,
please refer to a qualified expert. Horizontally mounted panels should also be picked
up from a minimum of every second panel to properly spread the load.

LED PAR Hex-7
5
Use only professional trussing system if the item shall be lowered from the ceiling or
high joists. Never let the device swing freely in a room.
CAUTION: Overhead Items may cause serious injuries when crashing down!! If there
is concern about the safety then DO NOT INSTALL the device.
DANGER OF FIRE!
When installing the device, make sure there is no highly-flammable material
(decoration articles, etc) within a distance of min. 0.5m.
Mount the projector with the mounting bracket to your trussing system using an
appropriate clamp.
For overhead use, always install a safety-rope that can hold at least 10 times the
weight of the fixture. You must only use safety –ropeswith quick links with screw
cap. Pull the safety-rope through the hole in the mounting bracket and over the
trussing system or a safe fixation spot. Insert the end in the quick link and tighten the
safety screw. The maximum drop distance must never exceed 20cm
A safety rope which already held the strain of a crash or which is defective must not
be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by
an expert.

LED PAR Hex-7
6
1.2. Power Connection
!! CAUTION !!
Never leave this device running unattended!! Every person that is involved with this
item has to be qualified!!
Connect item with main plug. The voltage and frequency must exactly be the same as
stated on the device. The power plug must always be inserted without force.
1.3. Cleaning and Maintenance
Please make sure that safety-relating and machine-technical installations are
inspected by a skilled person once a year.
1. Make sure before installing that all screws are tightly connected and not corroded.
2. There must be no deformations on the housings, fixations and installations spots
3. No damages must be showed on the power supply cables, material fatigue and
sediments
If the exterior of the unit is going to be cleaned, please use moist, lint free cloths.
Never use alcohol or solvents.
The Cooling fan must be cleaned monthly and check to ensure it is free of
obstructions.
To clean the interior of the device please use a vacuum cleaner or an air jet, however
we recommend cleaning the lenses weekly to ensure the best output from your unit.

LED PAR Hex-7
7
2.0 Menu navigation
Menu Level 1
Menu Level 2
Remark
A
u
t
o
A
u
t
o
S
p
e
e
d
Default：
Auto0(Auto
1-4)
A
u
t
o
0
A
u
t
o
0
1
0
0
Speed
Default：
100
A
u
t
o
1
1
0
0
A
u
t
o
2
1
0
0
A
u
t
o
3
1
0
0
A
u
t
o
4
1
0
0
S
t
a
t
i
c
S
t
a
t
i
c
F
i
x
C
F
i
x
C
F
i
x
C
R
G
B
A
W
P
R
G
R
B
R
A
R
W
R
P
G
B
G
A
G
W

LED PAR Hex-7
8
G
P
B
A
B
W
B
P
A
W
A
P
W
P
R
G
B
R
G
A
R
G
W
R
G
P
R
B
A
R
B
W
R
B
P
R
A
W
R
A
P
R
W
P
G
B
A
G
B
W
G
B
P
B
A
W
B
A
P
A
W
P
B
W
P
G
A
W
G
A
P

LED PAR Hex-7
9
G
W
P
R
G
B
A
R
G
B
W
R
G
B
P
R
G
A
W
R
G
A
P
R
G
W
P
R
B
A
W
R
B
A
P
R
B
W
P
R
A
W
P
G
B
A
W
G
B
A
P
G
B
W
P
G
A
W
P
B
A
W
P
R
G
B
A
W
R
G
B
A
P
R
G
B
W
P
R
G
A
W
P
R
B
A
W
P
G
B
A
W
P
R
G
B
A
W
P
M
a
n
u
C
M
a
n
u
a
l
Default：
RGBAWP=
255

LED PAR Hex-7
10
R
=
2
5
5
0-255
G
=
2
5
5
B
=
2
5
5
A
=
2
5
5
W
=
2
5
5
P
=
2
5
5
D
i
m
M
o
d
e
D
i
m
M
o
d
e
Default：
Off
D
I
M
1
O
f
f
D
I
M
1
D
I
M
2
D
I
M
3
B
a
c
k
L
i
t
e
B
a
c
k
L
i
t
e
Default：
:On
O
n
O
n
1
0
S
2
0
S
3
0
S
I
n
f
o
A
u
t
o
A
u
t
o
T
e
s
t
T
e
s
t
F
i
x
H
o
u
r
s
Default：0H
0
H
(0-9999H)
V
e
r
s
i
o
n
V
1
.
0
A
d
d
r
e
s
s
A
d
d
r
e
s
s
DMX
address
(001-512)

LED PAR Hex-7
11
0
0
1
5
1
2
Default：
001
6Ch：（
001-507）
8Ch：（
001-505）
12Ch：（
001-501）
HSV：（
001-510）
HSI：（001-
510
C
h
a
n
n
e
l
C
h
a
n
n
e
l
DMX
Channel
mode
1
2
C
h
6
C
h
Default：12
Ch
8
C
h
1
2
C
h
H
S
V
H
S
I
M
&
S
M
o
d
e
M
&
S
M
o
d
e
Default：
Slave
<
M
a
s
t
e
r
>
M
a
s
t
e
r
S
l
a
v
e
W
h
i
t
e
B
a
l
a
n
c
e
V
a
l
u
e
White
Balance
(125 -255)
B
a
l
a
n
c
e
R
=
2
5
5
R
=
2
5
5
Default RGB
255
G
=
2
5
5
G
=
2
5
5
B
=
2
5
5
B
=
2
5
5
T
e
m
p

LED PAR Hex-7
12
3.0 DMX Allocation
6-CH
Function
Value
Percent/Setting
1
Red
000-255
0~100%
2
Green
000-255
0~100%
3
Blue
000-255
0~100%
4
Amber
000-255
0~100%
5
White
000-255
0~100%
6
Purple
000-255
0~100%
8-CH
Function
Value
Percent/Setting
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%
5
Amber
000-255
0~100%
6
White
000-255
0~100%
7
Purple
000-255
0~100%
8
strobe
000-010
NO Function
011-255
Strobe slow to fast
12-CH
Function
Value
Percent/Setting
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%

LED PAR Hex-7
13
5
Amber
000-255
0~100%
5
White
000-255
0~100%
7
Purple
000-255
0~100%
8
strobe
000-010
NO Function
011-255
Strobe slow to fast
Manual
Color + Color
Temperature
000~010
No Function
011~030
R 100%, G 0~100%, B 0%
031~050
R 100%~0%, G 100%, B 0%
051~070
R 0%, G 100%, B 0~100%
071~090
R 0% G 100%~0% B 100%
091~110
R 0%~100% G 0% B 100%
111~130
R 100% G 0% B 100%~0%
131~150
R 100% G 0%~100% B 0%~100%
151~170
R 100%~0% G 100%~0% B 100%
171~200
R 100% G 100% B 100% W100%
9
201~205
Color temperature1
206~210
Color temperature2
211-215
Color temperature3
216-220
Color temperature4
221-225
Color temperature5
226-230
Color temperature6
231-235
Color temperature7
236-240
Color temperature8
241-245
Color temperature9
246-250
Color temperature10
251-255
Color temperature11

LED PAR Hex-7
14
Auto
Programs
000-010
No Function
011-060
Auto Program 1
061-120
Auto Program 2
10
121-180
Auto Program 3
181-240
Auto Program 4
241-225
Auto Program 0 (Auto1-5)
11
Auto Speed
000-255
Speed Slow to Fast
Dim Mode
000-051
Preset dimmer speed from display menu
052-101
Dimmer speed mode off
12
102-152
Dimmer speed mode1 (fast speed)
153-203
Dimmer speed mode2 (middle speed)
204-255
Dimmer speed mode3 (slow speed)
HSV
Function
Value
Percent/Setting
1
H
000-255
Hue
2
S
000-255
Saturation
3
V
000-255
Value(Brightness)
HSI
Function
Value
Percent/Setting
1
H
000-255
Hue
2
S
000-255
Saturation
3
I
000-255
Intensity

LED PAR Hex-7
15
4.0 TECHNICAL SPECIFICATIONS
Color 1m LUX 3m LUX 5m LUX 7m LUX 10m LUX
R
G
B
A
W
P
RGB
RGBA
RGBW
RGBAWP
8844
982.6
353.7
18.18
2.01
0.727
3495
388.3
139.8
1598
177.6
63.93
761.1
84.56
30.44
3540
393.4
141.6
1486
165.2
59.46
c
Please note:Information is subjectto change withoutprior notice ©
Power supply: 100 -240 V AC, 50/60 Hz ~
Fuse:T1A 250V
Power consumption: 53.4 W
Light Source: LED 6 IN 1 (10W 120°)
Beam Angle: 23°
Dimensions (LxWxH): 253 x 98 x 289.8 mm
Weight: 3.2kg
Maximum ambient temperature Ta: 45° C
Maximum housing temperature TC (steady state): 50°
Please note: Information is subject to change without prior notice ©