Shuttle FB86 User manual

FB86
Intel Pentium 4 Desktop , LGA 775 Processor
Based MAINBOARD

Shuttle®FB86
Intel Pentium 4 Desktop
LGA 775 Processor Based Mainboard
Copyright
Copyright©2004 by Shuttle®Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a retrieval system,
translated into any language, or transmitted in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without
prior written permission from Shuttle®Inc.
Disclaimer
Shuttle®Inc. shall not be liable for any incidental or consequential damages resulting from the
performance or use of this product.
This company makes no representations or warranties regarding the contents of this manual.
Information in this manual has been carefully checked for reliability; however, no guarantee is
given as to the correctness of the contents. In the interest of continued product improvement,
this company reserves the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to notify any
person of such revision or changes. The information contained in this manual is provided for
general use by the customers.
Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel, Pentium is a registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice: Other product names used in this manual are ascribed to their respective
owners and acknowledged.
M969

Statement of Shuttle Mainboard via the EMI Test
Shuttle mainboards have been via the EMI test in terms of series of regulations: EN55022/
CISPR22/AS/NZS3548 Class B, EN55024 (1998/AS/NZS), EN4252.1 (1994), EN61000,ANSI
C63.4 (1992), CFR47 Part 15 Subpart B, and CNS13438 (1997). The items tested are illus-
trated as follows:
(A)Voltage:AC110V/60HZ &AC230V/50HZ
(B) Tested Product Information:
Product Name: PC Mainboard
Status: Sample
ModelName: FB86
S/N:N/A
CPU:
External Frequency: 133 MHz
Intel Pentium 4, LGA 775 Processor: 2.53/ 2.66/ 2.8/ 2.93 GHz
External Frequency: 200 MHz
Intel Pentium 4, LGA 775 Processor: 2.8/ 3/ 3.2/ 3.4/ 3.6 GHz
Serial Port: one port with 9 pins
VGA Port: one port with 15 pins
Keyboard Port: one port with 6 pins
Mouse Port: one port with 6 pins
USB 2.0 Port: four ports with 4 pins respectively
1394a Port: two ports with 6 pins respectively
Mic-In Port: one port
Line-OUt Port: five ports
Line-InPort:one port
SPDIF-Out (Coaxial) Port: one port
SPDIF-Out (Optical) Port: one port
SPDIF-In (Optical) Port: one port
Clear CMOS button: one port
DIMM Memory (optional): DDR 400 256 MB *2
Power Cable: Detachable and Shielded (with a GND pin)
Monitor:CRT+DVI
Maximum Resolution: 1280 X 1024 V:60Hz
All CPUs have completely been tested, and values offered by the worst EMI combination of
CPU external frequency are listed as follows:
Test Mode External Frequency CPU CPU Open/Close
1200MHz P4 3.6 GHz Close
2200MHz P4 3.6 GHz Open
3133MHz P4 2.93 GHz Close
4133MHz P4 2.93 GHz Open

(C) Remedy for the Tested Product & Its EMI Interference:
Remedy:N/A
EMIInterference:
Crystal:14.318MHz(X2)/ 25MHz(X3)/32.768KHz(X1)/ 24.576MHz(X4)
ClockGenerator: U4
(D) Supported Host Peripherals:
Host Peripheral ProductName Model Name
# 1 Case FB86
# 2 Power Supply PC45I2753
# 3 SerialATAWesterm Digital WD1200JD-00FYB0
# 4 Panasonic FDD JU-257A606P
# 5 PioneerDVD Player DVD-116
(E) Notices for Assembling Computers:
1. Cases should be made of iron or other metal that has good electric conductivity.
2. Cylinders in a case should be made of metal, and as having a mainboard mounted
in a case, make sure screws are all utilized and fastened on a mainboard.
3.An I/O shielding should be contacted with I/O metallic parts of a mainboard.
4. Cables should appropriately be arranged and fixed in a case. Follow instructions:
Ø Leave IDE cables not crossed upon CPU and SDRAM;
Ø Leave power cables minimum in length, and not crossed upon a mainboard;
Ø Leave CPU fan cables minimum in length, and not near CPU;
Ø Leave cables on panels and other spare cables tied in a computer case.
5.Makesure an EMI shielding attachedtoa case has properly beeninstalled.
6. Make sure a 5.25" and screws are fastened to an EMI shielding.
7. Make sure a case is closely in contact with EMI connected points.
8. Make sure there is no cleft in a case which is not deformed.
9. Make sure a PCI door is bound to a case.
10. Make sure cables of other devices (fans or some others) are fixed in a case.

Important Safety Information
SAFETY INSTRUCTIONS
1. Pleasereadthesesafetyinstructionscarefully.
2. PleasekeepthisUser‘sManual for later reference.
3. Pleasedisconnectthis equipment fromACoutlet before cleaning. Don‘tuse liquid
orsprayeddetergentforcleaning.
4. Forpluggableequipment,thesocket-outletshall be installed near the equipment
andshall be easilyaccessible.
5. Pleasekeepthisequipmentfromhumidity.
6. Laythisequipmentonareliablesurfacewheninstall.A droporfall could cause injury.
7. Donotleavethis equipment in an environmentunconditioned,itmaydamage the
equipment.
8. Theopeningsonthe enclosure are for airconvectionhenceProtectthe equipment
fromoverheating.DONOTCOVERTHEOPENINGS.
9. Makesurethevoltageofthe power source when connect theequipmenttothe
poweroutlet.
10. Placethepowercordsuchawaythatpeoplecannotsteponit.Donotplaceanything
overthepowercord.Thepower cord must be ratedfortheproductandforthevoltage
andcurrent marked on the product’selectrical ratings label.The voltage and current
ratingofthecord should be greater thanthevoltageandcurrent rating marked on the
product.
11. Allcautionsandwarnings on the equipment shouldbenoted.
12. Ifthe equipmentisnotuse forlongtime,disconnecttheequipmentfrommainstoavoid
beingdamagedbytransientover-voltage.
13. Neverpouranyliquidintoventilationopenings,thiscouldcausefireorelectricalshock.
14. CAUTION:Thecomputeris provided with a battery-powered real-timeclockcircuit.
Thereisa danger of explosionifbattery is incorrectly replaced.
Replaceonlywithsameorequivalenttyperecommendedbythemanufacture.
Discardusedbatteries according tothemanufacturer’s instructions.
15. THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY WITHAPPROPRI-
ATESAFETYSTANDARDS INCLUDING IEC60825.
CAUTION :RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
CLASS 1 LASER PRODUCT

- 1 -
TABLE OF CONTENTS
WHAT'S IN THE MANUAL.................................................................... 5
Quick Reference............................................................................................... 5
About This Manual ........................................................................................... 5
1 INTRODUCTION................................................................................ 6
1.1 TO DIFFERENT USERS ............................................................................. 6
FIRST-TIMEDIYSYSTEMBUILDER ....................................................... 6
EXPERIENCEDDIY USER .................................................................... 6
SYSTEMINTEGRATOR .......................................................................... 6
1.2 ITEM CHECKLIST....................................................................................... 7
2 FEATURES ........................................................................................ 8
2.1 SPECIFICATIONS ....................................................................................... 8
3 HARDWARE INSTALLATION.......................................................... 11
3.1 STEP BY STEP INSTALLATION................................................................11
Accessories of FB86..............................................................................11
STEP1CPUInstallation ........................................................................ 12
STEP 2 Set Jumpers............................................................................. 14
STEP3 Install DDR SDRAMSystem Memory........................................ 14
STEP 4Install InternalPeripheralsin SystemCase ................................ 15
STEP5 Mount theMainboardon the ComputerChassis........................ 16
STEP6ConnectFront-PanelConnector................................................ 16
STEP 7 Connect IDE, Floppy and SerialATADisk Drives ...................... 17
STEP8ConnectOtherInternalPeripherals............................................ 18
STEP9InstallAdd-onCards inExpansion Slots .................................... 20
STEP10Connect Power Supply ........................................................... 20
STEP11 Connect External Peripheralsto Back-panel ........................... 21
STEP 12 First Time System Boot Up ..................................................... 22
STEP13InstallDriver & Software Components ..................................... 23

- 2 -
3.2 JUMPER SETTINGS ................................................................................. 24
JUMPERS&CONNECTORSGUIDE.................................................... 25
Back-Panel Connectors
1394a Port ............................................................................................ 28
PS/2 Keyboard & PS/2 Mouse Ports ..................................................... 28
ClearCMOS Button............................................................................... 28
COM Port .............................................................................................. 28
VGAPort ............................................................................................... 28
GigaLAN Port ....................................................................................... 28
USB Ports ............................................................................................. 29
SPDIF-OutCoaxial Port......................................................................... 29
SPDIF-OutOpticalPort ......................................................................... 29
7.1ChannelBass/CenterPort................................................................ 29
7.1ChannelRear-OutPort ..................................................................... 29
SPDIF-InOpticalPort ............................................................................ 30
7.1ChannelFront-OutPort..................................................................... 30
7.1ChannelSurround-BackPort ............................................................ 30
Line-InPort ............................................................................................ 30
Front-Panel Connector
FRONTPANEL Connector (JP7) ........................................................... 31
Internal Peripherals Connectors
EnhancedIDEandFloppyConnectors................................................... 32
SerialATA Connectors........................................................................... 32
Other Connectors
ATXPower Supply Connectors(ATX1/BTX1) ........................................ 33
FanConnectors-FAN1/2/3 .................................................................... 34
AUX-INConnector(CN2)....................................................................... 34

- 3 -
CD-IN(CN3)(Black)/ Mini CD-IN (CN4)Connectors ............................... 35
WirelessKeyboard and Mouse Connector(JP3).................................... 35
EXT.Print Port (JP4) ............................................................................. 36
USBHeader (USB1/USB3/JP2)............................................................ 37
EXT.GPIHeader(JP1).......................................................................... 37
3.3 SYSTEM MEMORY CONFIGURATION ..................................................... 38
INSTALLMEMORY................................................................................ 38
UPGRADEMEMORY............................................................................ 38
4 SOFTWARE UTILITY ......................................................................39
4.1 Mainboard CD Overview ......................................................................... 39
4.2 Install Mainboard Software ..................................................................... 40
4.2.A Install Intel Chipset Driver .................................................................... 41
4.2.B Install Intel VGA Driver.......................................................................... 41
4.2.C Install Intel IAA Driver............................................................................ 42
4.2.D Install Marvell Giga LAN Driver ............................................................ 42
4.2.E Install Intel USB 2.0 Driver.................................................................... 43
4.2.F Install Intel High Definition Bus ........................................................... 43
4.2.G Install Intel High Definition Audio Driver ............................................. 44
4.2.H Install DirectX9 Utility ........................................................................... 44
4.3 View the User's Manual........................................................................... 45
5 BIOS SETUP ................................................................................... 46
5.1 Enter the BIOS .......................................................................................... 46
5.2 THE MAIN MENU ...................................................................................... 47
STANDARD CMOS FEATURES........................................................... 49
ADVANCED BIOS FEATURES............................................................. 52
ADVANCED CHIPSET FEATURES...................................................... 57
INTEGRATEDPERIPHERALS.............................................................. 59
POWERMANAGEMENTSETUP ......................................................... 64

- 4 -
PNP/PCICONFIGURATIONS ................................................................ 68
PCHEALTHSTATUS............................................................................ 70
FREQUENCY/VOLTAGECONTROL..................................................... 72
LOAD FAIL-SAFE DEFAULTS.............................................................. 74
LOADOPTIMIZEDDEFAULTS ............................................................. 74
SET PASSWORD ................................................................................. 75
SAVE & EXIT SETUP............................................................................ 76
EXITWITHOUTSAVING........................................................................ 76

- 5 -
WHAT'S IN THE MANUAL
Quick Reference
Hardware Installation >> Step-by-Step ................................................ Page 11
Jumper Settings >> A Closer Look.......................................................Page 24
Drivers/Software Utilities >> How to Install .........................................Page 39
BIOS Setup >> How to Configure.........................................................Page 46
About This Manual
For First-Time DIY System Builder.........................................................Page 6
For Experienced DIY User ......................................................................Page 6
For System Integrator .............................................................................Page 6

- 6 -
1INTRODUCTION
1.1 To Different Users
First-Time DIY System Builder
Welcome to the DIY world! Building your own computer system is not as diffi-
cult as you may think. To make your first computer DIY experience successful,
right from the start, we have designed the 3.1 Hardware Installation section
in a step-by-step fashion for all the first-time DIY system builders. Prior to instal-
lation, we also suggest you to read the whole manual carefully to gain a com-
plete understanding of your new Shuttle FB86 mainboard.
Experienced DIY User
Congratulate on your purchase of the Shuttle FB86 mainboard. You will find
that installing your new Shuttle FB86 mainboard is just easy. Bundled with an
array of onboard functions, the highly-integrated FB86 mainboard provides you
with a total solution to build the most stable and reliable system. Refer to sec-
tions 3.2 Jumper Settings and Chapter 4 Drivers/Software Utilities to
find out how to get the best out of your new mainboard. Chapter 5 BIOS
Setup also contains the relevant information on how to tune up your system to
achieve higher performance.
System Integrator
You have wisely chosen Shuttle FB86 to construct your system. Shuttle FB86
incorporates all the state-of-the-art technology of the 915G + ICH6R chipset
from Intel. It integrates the most advanced functions you can find to date in a
compact BTX board.

- 7 -
1.2 Item Checklist
Check all items with your FB86 mainboard to make sure nothing is missing.
The complete package should include:
-One piece of Shuttle FB86 Mainboard
-One piece of ATA 100/66/33 Ribbon Cable
-One piece of Floppy Cable (Optional)
-One piece of Serial ATA Cable
-FB86 User's Manual
-ICH6R RAID Manual
-One piece of Bundled CD-ROM with containing:
ØFB86 user's manual saved in PDF format
ØInstall Intel Chipset Driver
ØInstall Intel VGA Driver
ØInstall Intel IAA Driver
ØInstall Marvell Giga LAN Driver
ØInstall Intel USB 2.0 Driver
ØInstall Intel High Definition Bus
ØInstall Intel High Definition Audio Driver
ØInstall DirectX9 Utility
ØAward Flashing Utility
SERIAL
ATA
V
S
O
B
T
X
1
B
T
X
1
B
T
X
1
J
P
2
1
44106T1417E
ALC880
PCI1
ADD1
JP4
CN4
SATA1 SATA2 SATA3 SATA4
IDE1
USB1
1
1 1
1
CN3 CN2
1
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
V
T
6
3
0
7
0
4
2
1
C
D
T
A
I
W
A
N
2
H
A
1
0
4
9
1
3
8
U
S
B
3
1
F
A
N
1
JP1
1
FAN2
FAN3
ATX1
BTX1
JP7
JP3
1
D
I
M
M
1
D
I
M
M
2
FDD1
1

- 8 -
2 FEATURES
FB86 mainboard is carefully designed for the demanding PC user who wants high perfor-
mance and maximum intelligent features in a compact package.
2.1 Specifications
-CPU Support
Intel Pentium 4 Desktop Processors in the LGA 775 pin package with 533 /
800 MHz FSB.
-Chipset
Features Intel 915G N.B. and ICH6R S.B..
Onboard Lan
Marvell 88E8053 Lan Chipset support 10/100/1000 Mbps operation rate and
wake-on-Lan (WOL) function.
Onboard 1394a
VIA VT6307, supports 400 Mb/s, 200 Mb/s, or100 Mb/s data transfer rate.
-Jumperless CPU Configuration
Soft-configuration FSB (The FSB speed is software configurable from 100 MHz
to 355 MHz of BIOS setup program.)
-On Board 7.1 Channel High Definition Audio
Realtek ALC880 supports 16/20/24 bits ADC and DAC resolution and 7.1
channel slot selectable DAC Output for multi-channel applications.
-Versatile Memory Support
Features the dual-channel mode of 128 bit data transfer rate.
Two 184-pin DIMM slots to support up to 4GB of PC2700 or PC3200 compli-
ant unbuffered without ECC DDR SDRAM module.
Available bandwidth up to 3.2 GB/s(DDR400) for Single Channel mode and
6.4 GB/s(DDR400) in Dual Channel mode. System memory supports 128Mb/
256Mb/ 512Mb/ 1Gb technologies up to 4GB capacity max and 2GB per DIMM.
-PCI Express Graphics & SDVO Interface Slot
The GMCH multiplexes a PCI Express interface with two Intel SDVO ports.
One 16-Lane PCI Express port for Graphic Attach, fully compliant to the PCI
Express Base Specification 1.0a.
The X16 port operates at a frequency of 2.5 Gb/s while employing 8b / 10b
encoding. Supports Analog / Digital display & TMDS transmitters or TV-OUT
encoders via an Advance Digital Display card.

- 9 -
-USB 1.1/2.0 Complaint Interface Onboard
Ø4 UHCI host controller, 1 EHCI host controllers to support 8 USB 1.1/2.0
devices. All 8 USB ports can be assigned to USB 2.0 interface with BIOS
option
-I/O Interface
Provides a variety of I/O interfaces:
Ø1 x 1394a port.
Ø1 x PS/2 Mouse port.
Ø1 x PS/2 Keyboard port.
Ø1 x Clear CMOS Button.
Ø1 x DB9 Serial port.
Ø1 x DB15 VGA connector.
Ø1 x Giga LAN port.
Ø2 x USB 1.1/2.0 ports.
Ø1 x SPDIF-Out Coaxial port.
Ø1 x SPDIF-Out Optical port.
Ø1 x 7.1 Channel Bass/Center port.
Ø1 x 7.1 Channel Rear-Out port.
Ø1 x SPDIF-IN Optical port.
Ø1 x 7.1 Channel Front-Out port.
Ø1 x 7.1 Channel Surround-Back port.
Ø1 x Line-In port.
-PCI Bus Master IDE Controller Onboard
One Ultra DMA 100/66/33 Bus Master Dual-channel IDE ports provide sup-
port to a maximum of two IDE devices (one Master and one Slave per channel).
The IDE Bus implements data transfer speeds of up to 100/66/33 MB/sec and
also supports Enhanced PIO Modes. 80-pin Cable Backward Compatible Legacy
ATAPI Devices, ATAPI IDE CD-ROM, CD-R, CD-RW, and LS-120 supports.
-ATX Power Supply Connector
ATX power supply unit can connect to the onboard 24-pin Pentium 4 standard
ATX power connectors, supporting Suspend and Soft-On/Off by dual-function
power button. The Pentium 4 ATX power include other 4-pin +12V ATX power
connector.

- 10 -
-Advanced Configuration and Power Interface
Features four power saving modes: S1 (Snoop), S3 (Suspend to RAM), S4 (Sus-
pend to DISK), and S5 (Soft-Off). ACPI provides more efficient Energy Saving
Features controlled by your operating system that supports OS Direct Power
Management (OSPM) functionality.
-System BIOS
Provides licensed Award BIOS V6.0 PG on 4Mb Flash core and supports Green
PC, Desktop Management Interface (DMI).
-Form Factor
System board conforms to BTX specification.
Board dimension: 266.7 mm x 227 mm.
-Advanced Features
ØLow EMI - Built in spread spectrum to reduce EMI.
ØDual Function Power Button - The system can be in one of two states,
one is Suspend mode and the other is Soft-Off mode. Pushing the power
button for less than 4 seconds places the system into Suspend mode.
When the power button is pressed for longer than 4 seconds, the system
enters Soft-Off mode.
ØModem Ring Power-On - The system can be powered on automatically
by the activation of modem ringing.
-Intelligent Features
ØVoltage Monitoring - Monitors various voltages of key elements, such
as the CPU, and other critical system voltage levels to ensure stable
current passing through mainboard components.
ØFan Status Monitoring -To prevent CPU from overheating, the CPU fan
is monitored for RPM and failure. (CPU Cooling FAN with RPM sensor is
required.)
ØTemperature Monitoring -This item allows users to make sure whether
the CPU or system runs in a suitable temperature.
ØCPU Fan AutoGuardian -This SMART Bios enabled Variable Fan
Speed and CPU temperature Control feature.

- 11 -
3HARDWAREINSTALLATION
Before removing or installing any of these devices including CPU, DIMMs,
Add-On Cards, Cables, please make sure to unplug the onboard power
connector.
This section outlines how to install and configure your mainboard. Refer to the following
mainboard layout to help you to identify various jumpers, connectors, slots, and ports. Then
follow these steps designed to guide you through a quick and correct installation of your
system.
3.1 Step-by-Step Installation
Accessories Of FB86
J
P
2
1
44106T1 417E
ALC880
PCI1
ADD1
JP4
CN4
SATA1 SATA2 SATA3 SATA4
IDE1
USB1
1
1 1
1
CN3 CN2
1
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
3
4
6
5
6
0
4
S
E
P
C
V
T
6
3
0
7
0
4
2
1
C
D
T
A
I
W
A
N
2
H
A
1
0
4
9
1
3
8
U
S
B
3
1
F
A
N
1
JP1
1
FAN2
FAN3
ATX1
BTX1
JP7
JP3
1
D
I
M
M
1
D
I
M
M
2
PS/2 Keyboard/Mouse s
Port
SerialATA Ports- SATA1~4
7.1-Channel Center/Bass/7.1-Channel Rear
-Out/SPDIF-IN Optical/7.1-Channel Front-Out/
7.1-Channel Surround-Back/Line-In Ports 1394aPort
SPDIF-OUT Coaxial/SPDIF-OUT Optical Ports Clear CMOS Button
Giga LAN(GbE)/USB 2.0/1.1 Ports
EXT.Print Port -
JP4
Power Connector- BTX1
FAN Connector- FAN2
FAN Connector- FAN1
ICH6RChipset
Front Panel Connector-
JP7
Two 184-pins DIMM Slots
USBHeader- USB3
AUX-IN- CN2
OnePCISlot
COM/VGAPorts
CD-IN- CN3
Mini CD-IN- CN4
USB Header- USB1
OneIDE Slot
Intel 915G Chipset
USB Header- JP2
EXT.GPI Header- JP1
LGA775PackageCPUSocket
Power Connector- ATX1
Wireless Keyboard/Mouse
Select Header- JP3
FAN Connector- FAN3
OnePCI-ESlot
FDD1
1
OneFloppy Slot

- 12 -
Step 1
CPU Installation:
This mainboard supports Socket 775 Intel Pentium 4 Desktop processor
(CPU).
To install, follow the steps outlined below. Note the CPU orientation carefully
when you insert it into the socket.
Caution :This 775 pin socket is fragile and easily damaged.
Always use extreme care when installing a CPU and limit the
number of times that you remove or change the CPU.
1. Remove the protective cover.
2. Unlock the socket lever and lift it to 90-degrees (be careful not to touch the
socket pins during this process).
2
1
3

- 13 -
3. Orientate the CPU and socket, aligning the yellow triangle on the corner of
the CPU with the triangle on the socket. Gently insert. Take care not to place
any sideways force on the CPU when inserting, as the socket is fragile and
easily damaged.
4. Lower the CPU socket lever and lock in place.
5. The Socket 775 processor requires a heat sink and cooling fan to run effi-
ciently, cool and stable. If you do not receive a bundled heat sink and fan
when you purchase you CPU, it is essential that you acquire one.
Note :The CPU might be damaged
if you do not match the CPU
socket Pin 1 and cut edge well.
L
e
v
e
r
P
e
n
t
i
u
m
4
,
L
G
A
7
7
5
P
r
o
c
e
s
s
o
r
Triangle Markings

- 14 -
Step 2
Set Jumpers
This mainboard is jumperless! The default jumper settings have been set for the
common usage standard of this mainboard. Therefore, you do not need to reset
the jumpers unless you require special adjustments as any of the following cases:
1. Clear CMOS
For first-time DIY system builders, we recommend that you do not change the
default jumper settings if you are not totally familiar with the mainboard con-
figuration procedures. The factory-set default settings are tuned for optimum
system performance. For the advanced users who wish to customize their sys-
tem, section 3.2 Jumper Settings will provide detailed information on how to
configure your mainboard manually.
Caution: If you did not place the battery apropriately, which may cause
risk of explosion. Please pefer to the related rule for the dis-
pose of used batteries.
Step 3
Install DDR SDRAM System Memory
To install memory, insert DDR SDRAM memory module(s) in DIMM slot(s).
Note that DDR SDRAM modules are directional and will not go in the DIMM
slots unless properly oriented. After the module is fully inserted into the DIMM
slots, lift the clips of both sides of the DIMM slot to lock the module in place.
Do not remove memory modules while DIMM LED is on. It might cause short
or other unexpected damages due to the 2.6V stand by voltage. Remove memory
modules only when AC Power cord is disconnected.
DDR SDRAM DIMM Power LED
DIMM
Power
LED
(Green)

- 15 -
Step 4
Install Internal Peripherals in System Case
Before you install and connect the mainboard into your system case, we rec-
ommend that you first assemble all the internal peripheral devices into the com-
puter housing, including but not limited to the hard disk drive (IDE/HDD), floppy
disk drive (FDD), CD-ROM drive, and ATX power supply unit. This will greatly
facilitate in making the connections to the mainboard described below.
To install IDE & FDD drives, follow this procedure:
1. Set the required jumpers on each device according to the instructions pro-
vided by the manufacturer. (IDE devices, HDD, and CD-ROM, have to set
jumpers to Master or Slave mode depending on whether you install more
than one device of each kind.)
2. Connect IDE cable and FDD cable on the back-panel of the internal periph-
eral devices to the corresponding headers on board. Note that the cable
should be oriented with its colored stripe (usually red or magenta) connected
to pin#1 both on the mainboard IDE or FDD connector and on the device as
well.
3. Connect an available power cable from your system power supply unit to
the back-panel of each peripheral device. Note that the power cable is di-
rectional and cannot fit in if not properly positioned.