Siemens SICHARGE UC 100 User manual

Operating instructions
10/2022Edition
UC 100, 200, 300, 400, 600, 800
SICHARGE
siemens.com/sichargeuc
(8EM4000-XXXXX-XXXX)

SICHARGE
SICHARGE UC 100, UC 200, UC
300, UC 400, UC 600, UC 800
Operating Instructions
10/2022
A5E50828019-AC
Introduction 1
Safety information 2
Description 3
Application planning 4
Mounting 5
Connecting 6
Commissioning 7
Operating 8
Alarm, fault and system
messages 9
Maintenance and service 10
Disposal 11
Service & Support 12
Technical speci󹪝cations 13
Declaration of Conformity 14
UC 600/800 A
Abbreviations B

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Smart Infrastructure
Schuhstr. 60
91052 Erlangen
GERMANY
A5E50828019-AC
Ⓟ 11/2022 Subject to change
Copyright © SiemensAG 2021 - 2022.
All rights reserved

Table of contents
1 Introduction ........................................................................................................................................... 7
1.1 About the operating instructions.......................................................................................... 7
1.2 Open-source software.......................................................................................................... 8
2 Safety information................................................................................................................................. 9
2.1 Basic safety instructions ....................................................................................................... 9
2.2 The 󹪝ve safety rules for working with electrical equipment ................................................. 12
2.3 Emergency Stop button...................................................................................................... 13
2.4 Safety sign......................................................................................................................... 15
2.5 Cybersecurity at Siemens ................................................................................................... 16
2.6 Identi󹪝cation of the device................................................................................................. 16
3 Description........................................................................................................................................... 19
3.1 Description of UC 100 ........................................................................................................ 19
3.1.1 Product overview ............................................................................................................... 19
3.1.2 Display and operator controls............................................................................................. 20
3.1.3 Design of the charging station ........................................................................................... 22
3.1.4 Charging cable................................................................................................................... 23
3.2 Description of UC 200 ........................................................................................................ 25
3.2.1 Product overview ............................................................................................................... 25
3.2.2 Display and operator controls............................................................................................. 27
3.2.3 Design of the charging station ........................................................................................... 28
3.2.4 Charging cable................................................................................................................... 30
3.3 Description of UC 300/400 ................................................................................................. 32
3.3.1 Product overview ............................................................................................................... 32
3.3.2 Display and operator controls............................................................................................. 33
3.3.3 Design of the charging station ........................................................................................... 35
3.4 Decentralized charge points ............................................................................................... 36
3.5 Electrical protection devices ............................................................................................... 37
4 Application planning ........................................................................................................................... 39
4.1 Checking incoming goods .................................................................................................. 39
4.1.1 Checking the delivery for completeness and correctness ..................................................... 39
4.1.2 Checking the transport packaging ...................................................................................... 39
4.1.3 Unpackaging the charging station ...................................................................................... 40
4.1.4 Report missing delivery components or transport damage.................................................. 41
4.2 Application planning of UC 100.......................................................................................... 41
4.2.1 Location planning .............................................................................................................. 41
4.2.2 Preparing the base area...................................................................................................... 47
4.3 Application planning of UC 200.......................................................................................... 50
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 3

4.3.1 Location planning .............................................................................................................. 50
4.3.2 Preparing the base area...................................................................................................... 55
4.4 Application planning of UC 300/400................................................................................... 58
4.4.1 Location planning .............................................................................................................. 58
4.4.2 Preparing the base area...................................................................................................... 63
4.5 Storing the charging station ............................................................................................... 66
4.6 Transporting the charging station....................................................................................... 67
5 Mounting ............................................................................................................................................. 69
5.1 Safety instructions ............................................................................................................. 69
5.2 Positioning the charging station ......................................................................................... 69
5.3 Installation of UC 100 ........................................................................................................ 70
5.3.1 Inserting the connecting cable into the cabinet .................................................................. 70
5.3.2 Securing the charging station............................................................................................. 73
5.4 Installation of UC 200 ........................................................................................................ 74
5.4.1 Inserting the connecting cable into the cabinet .................................................................. 74
5.4.2 Securing the charging station............................................................................................. 77
5.5 Installation of UC 300/400 ................................................................................................. 78
5.5.1 Inserting the connecting cable into the cabinet .................................................................. 78
5.5.2 Securing the charging station............................................................................................. 81
6 Connecting .......................................................................................................................................... 83
6.1 Safety instructions ............................................................................................................. 83
6.2 General information about power cables ............................................................................ 83
6.3 Connecting UC 100............................................................................................................ 85
6.3.1 Connecting the power supply cable.................................................................................... 85
6.3.2 Connecting DC cables ........................................................................................................ 88
6.3.3 Connecting the communication cable ................................................................................ 91
6.3.4 Connecting the auxiliary power supply............................................................................... 92
6.4 Connecting UC 200............................................................................................................ 94
6.4.1 Connecting the power supply cable.................................................................................... 94
6.4.2 Connecting DC cables ........................................................................................................ 96
6.4.3 Connecting the communication cable ................................................................................ 99
6.4.4 Connecting the auxiliary power supply............................................................................. 100
6.5 Connecting UC 300/400................................................................................................... 102
6.5.1 Connection options.......................................................................................................... 102
6.5.2 Connecting the power supply cable.................................................................................. 103
6.5.3 Connecting DC cables ...................................................................................................... 105
6.5.4 Connecting the communication cable .............................................................................. 107
6.5.5 Connecting the auxiliary power supply............................................................................. 108
6.6 External communication .................................................................................................. 110
6.7 Re-attaching protective cover ........................................................................................... 111
7 Commissioning .................................................................................................................................. 113
7.1 Initial commissioning....................................................................................................... 113
Table of contents
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
4Operating Instructions, 10/2022, A5E50828019-AC

7.2 Switch on charging station............................................................................................... 116
8 Operating........................................................................................................................................... 121
8.1 Operating equipment variants.......................................................................................... 121
8.2 Safety instructions ........................................................................................................... 121
8.3 Plug in the charging cable................................................................................................ 122
8.4 Monitoring the charging process ...................................................................................... 123
8.5 Stop charging .................................................................................................................. 126
8.6 Unplugging the charging cable......................................................................................... 127
8.7 Displaying alarms............................................................................................................. 128
8.8 Operating the Service menu............................................................................................. 131
8.8.1 Selecting options ............................................................................................................. 131
8.8.2 Checking recorded alarms ................................................................................................ 132
8.8.3 Restarting the charging process after an alarm ................................................................. 134
8.8.4 Displaying information about the charging station............................................................ 136
8.8.5 Changing the display language ........................................................................................ 138
8.8.6 Displaying energy values of the charging process ............................................................. 139
8.8.7 Displaying the current and voltage trend of the charging process...................................... 140
9 Alarm, fault and system messages .................................................................................................... 143
9.1 "Emergency Stop" alarm message..................................................................................... 143
9.2 Alarm message "Cabinet's Door Opened" .......................................................................... 144
9.3 Alarm message "Ground Fault Detection".......................................................................... 145
9.4 Alarm messages in the alarm history ................................................................................ 147
10 Maintenance and service .................................................................................................................. 151
10.1 Safety instructions ........................................................................................................... 151
10.2 Maintenance plan ............................................................................................................ 152
10.3 Cleaning the touch screen................................................................................................ 155
10.4 Cleaning the cabinet ........................................................................................................ 156
10.5 UC 100 maintenance ....................................................................................................... 157
10.5.1 Replacing an air 󹪝lter........................................................................................................ 157
10.5.2 Replacing the cabinet fan................................................................................................. 159
10.6 UC 200 maintenance ....................................................................................................... 161
10.6.1 Replacing an air 󹪝lter........................................................................................................ 161
10.6.2 Replacing the cabinet fan................................................................................................. 163
10.7 UC 300/400 maintenance ................................................................................................ 165
10.7.1 Replacing an air 󹪝lter........................................................................................................ 165
10.7.2 Replacing the cabinet fan................................................................................................. 167
Table of contents
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 5

11 Disposal ............................................................................................................................................. 171
12 Service & Support .............................................................................................................................. 173
13 Technical speci󹪝cations ..................................................................................................................... 175
13.1 Technical speci󹪝cations .................................................................................................... 175
13.2 Power factor/e󹪟ciency ..................................................................................................... 177
13.3 Charging current/power curve.......................................................................................... 178
13.4 Derating .......................................................................................................................... 179
14 Declaration of Conformity ................................................................................................................. 181
A UC 600/800......................................................................................................................................... 183
A.1 Introduction .................................................................................................................... 183
A.2 Structure of UC 600/800 .................................................................................................. 183
A.3 Connection of UC 600/800............................................................................................... 185
B Abbreviations..................................................................................................................................... 187
Index .................................................................................................................................................. 189
Table of contents
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
6Operating Instructions, 10/2022, A5E50828019-AC

Introduction 1
1.1 About the operating instructions
These operating instructions contain the information required for safe operation and intended
use of the SICHARGE UC charging station.
Safekeeping the operating instructions
The operating instructions are an integral part of the product and an indispensable part of the
product safety concept. The following requirements therefore apply for safekeeping the
operating instructions:
• Keep the operating instructions for the entire service life of the charging station.
• Make the operating instructions easily accessible at all times for all persons involved.
• If you transfer the charging station to third parties, also pass along the operating instructions.
Using the operating instructions
How to use the operating instructions correctly:
• Make the operating instructions available to all persons involved before and during work on
the charging station.
• Read the operating instructions carefully before starting work.
• Follow the safety instructions and handling instructions.
Changes compared to the previous version
Compared to the previous product version with the edition 07/2021, this manual contains the
following changes:
• Creating the section Initial commissioning (Page113)
• Update of the section Connecting DC cables (Page88)
• Update of the section Connecting UC 200 (Page94)
• Update of the section Connecting DC cables (Page105)
• Update of the section Maintenance plan (Page152)
• Update of the section Charging current/power curve (Page178)
• Update of the chapter Declaration of Conformity (Page181)
• Update of the chapter Maintenance plan (Page152)
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 7

1.2 Open-source software
Open-source software is used in the 󹪝rmware of the product described. Open Source Software
is provided free of charge. We are liable for the product described, including the open-source
software contained in it, pursuant to the conditions applicable to the product. Siemens accepts
no liability for the use of the open source software over and above the intended program
sequence, or for any faults caused by modi󹪝cations to the software.
For legal reasons, we are obliged to publish the original text of the license conditions
and copyright notices. Please also read the information that is supplied with the product
or made available here (https://assets.new.siemens.com/siemens/assets/api/uuid:beda63de-
e83a-4598-9863-7645d0c0dda8/sicharge-uc-open-source-software.pdf).
Introduction
1.2Open-source software
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
8Operating Instructions, 10/2022, A5E50828019-AC

Safety information 2
2.1 Basic safety instructions
The charging station complies with all prescribed technical safety standards and thereby o󹪜ers
the greatest possible product safety. To ensure the safety of all persons, systems and equipment
at all times, adhere to the following basic safety instructions.
Guidelines and regulations
In order to ensure comprehensive safety, adhere to the following guidelines and regulations:
• Guidelines for occupational safety
• Regulations for prevention of accidents
• Trade regulations
• Technical connection conditions of the power supply unit
• Building regulations
• Generally accepted rules of technology
Target group
These operating instructions are intended for the following persons:
• Planners
– Planning the location of the charging station
• Carriers
– Transporting the charging station to the place of use
• Installers
– Mounting the charging station
•Quali󹪝ed electricians
– Connecting electrical cables to the charging station
– Perform electrotechnical work on the charging station
• Users
– Charging electric vehicles
• Service personnel
– Performing maintenance and servicing
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 9

Intended use
The intended use of the charging station is exclusively to charge the battery of an electric
vehicle. For this, the electric vehicle must be equipped with a charging socket of the type CCS
Combo 2. The charging station charges electric vehicles according to the standards EN 62196‑3
and EN61851‑23.
Depending on the equipment variant, the charging station o󹪜ers one of the following
charging options:
• With a charging cable at the station
• Via a distributed charge point:
– SICHARGE UC Dispenser
– SICHARGE MastHood
– SICHARGE MastPanto
Any other or additional use is not in accordance with the intended use and constitutes
misuse of the device. The charging station is suitable for indoor and outdoor use. The
permissible ambient conditions at the place of use must be observed for intended use.
Quali󹪝ed personnel
Non-electrical work, e.g. transport and assembly, may only be performed by quali󹪝ed personnel.
Quali󹪝ed personnel are quali󹪝ed by training and experience to recognize risks arising during the
respective work and to avoid possible hazards.
Electrical engineering work may only be performed by quali󹪝ed electricians themselves or
under their direction and supervision. A quali󹪝ed electrician is someone who is able to assess
the work assigned to them and recognize potential dangers due to their professional training,
knowledge and experience as well as knowledge of the relevant standards.
Work on a live charging station can only be performed by quali󹪝ed electricians that meet the
following requirement:
• Ability to work on live equipment according to DGUV regulation 103-011
• Ability to work in accordance with the regulations applicable to the installation site
Personal protective equipment (PPE)
Personal protective equipment protects you against hazards to your health and safety. Use your
personal protective equipment in accordance with occupational safety guidelines and accident
prevention regulations.
Fire and explosion protection
Do not store or use 󹪞ammable liquids that produce 󹪞ammable fumes, such as gasoline or
ethanol, in the vicinity of the charging station. Electrostatic charge or heat generated during
charging can ignite explosive and 󹪞ammable liquids.
Safety information
2.1Basic safety instructions
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
10 Operating Instructions, 10/2022, A5E50828019-AC

Protection against electromagnetic 󹪝elds
The electromagnetic emission in the charging station meets the IEC61851‑21‑2 standard:
• Noise immunity: ClassA
• Emission (radiated): ClassA
• Emission (conducted, AC input): ClassA
• Emission (conducted, AC port): ClassA
• Emission (conducted, DC port): Limits according to IEC 61851‑21‑2:2018
The charging station complies with immunity requirements for Class A industrial areas
according to the generic standard IEC61000‑6‑2:2016 Electromagnetic Compatibility(EMC).
WARNING
Danger to life from electromagnetic 󹪝elds when door is open
When the door is open, the switched-on charging station emits electromagnetic 󹪝elds (EMF) to
the outside. Electromagnetic 󹪝elds are particularly dangerous for people with pacemakers or
other implants in the immediate vicinity of a system.
• Therefore, switch o󹪜 the power supply before opening the door of the charging station.
• If you open the door forcibly, the charging station automatically switches o󹪜 the power
supply to the AC‑DC converters.
Protection against ingress of liquid
The protection standard of the cabinet protects the charging station against the ingress of splash
water from all directions. In particular, the protection standard prevents the penetration of
precipitation and protects against all liquids applied to the surface of the cabinet without
pressure.
Also protect the charging station from liquids that exert pressure on the surface of the
cabinet:
• Never use high-pressure cleaners or steam cleaners when cleaning the charging station.
• Place the charging station in a 󹪞ood-proof location.
WARNING
Electric shock due to ingress of liquid
Strong jets of water or 󹪞ooding can cause liquid to enter the charging station. Moisture or liquid
inside the charging station can cause electric shock.
If liquid has entered the charging station, take the following safety precautions:
• Take the charging station out of service by switching it o󹪜 at the electrical distributor.
•Quali󹪝ed personnel must dry the charging station and check it for damage.
Safety information
2.1Basic safety instructions
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 11

Protection against unauthorized opening
A lock system protects the charging station from unauthorized opening of the device door.
• Keep the key for the door locks safe against access by unauthorized persons.
• Only make the key available to authorized persons for work in the charging station.
• Do not leave the charging station unattended with the device door open.
Alterations to the device
The operating instructions describe all permissible changes to the charging station. Any other or
additional changes are not permitted. Unauthorized modi󹪝cations void the manufacturer's
warranty and the approvals of the device become invalid.
WARNING
Danger due to missing or unrecognizable safety signs and warnings
Missing or unrecognizable safety signs or warnings do not indicate that danger is not no longer
present. Undetected dangers can result in accidents with serious physical injury or death.
• Check the presence of all safety signs and warnings using the operating instructions
• Attach missing safety signs and warnings
• Do not remove safety signs and warnings
• Replace unrecognizable safety signs and warnings
Only use undamaged equipment or parts
WARNING
Electric shock in case of damaged equipment
Improper handling can damage the equipment. Damaged devices may have dangerous
voltages on the cabinet or exposed components, which can cause serious injury or death if
touched.
• Comply with the technical speci󹪝cations for transport, storage and operation.
• Check the charging cables and charging plugs for tampering, damage and foreign objects.
• Do not use a device if it is damaged.
2.2 The 󹪝ve safety rules for working with electrical equipment
The European standard EN 50110‑1 "Operation of electrical installations" prescribes safety rules
for electrical work on and in electrical installations. To ensure the safety of persons and property
in accordance with the standards, always comply with the following safety rules.
Safety information
2.2The 󹪝ve safety rules for working with electrical equipment
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
12 Operating Instructions, 10/2022, A5E50828019-AC

Securing an electrical system before starting work
Before starting work on and in electrical installations, apply the following 󹪝ve safety rules:
1. Disconnect
2. Secure against reclosing
3. Ensure there is no voltage present
4. Ground and short-circuit
5. Cover or shield adjacent live parts
Prepare to switch on again after work is 󹪝nished
After 󹪝nishing and checking the work, prepare the restart as follows:
• Inform persons no longer required that the work is completed and no further work is
permitted
• Withdraw persons no longer required
• Remove all tools, equipment and aids used
Switch on the electrical system again
After 󹪝nishing the work, remove the protective measures and switch the system on again:
1. Remove short-circuit
2. Remove grounding
3. Remove covers or barriers
4. Remove fuse to prevent restart
5. Switch the system back on
2.3 Emergency Stop button
In a hazardous situation, pressing the Emergency Stop button immediately puts the charging
station into a safe emergency stop state.
Safety information
2.3Emergency Stop button
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 13

Push-button position
The Emergency Stop button is positioned on the front of the charging station in the middle of
the device door.

①Emergency Stop button
Figure2-1 Push-button position
Function of the Emergency Stop button
The charging station immediately switches o󹪜 the power supply to the charging cable after the
emergency stop button is pressed. The charging station switches to a safe emergency stop state.
The charging station displays the "Emergency Stop" alarm message (Page143) on the touch
screen. For safety reasons, the charging station cannot be operated in emergency stop state. The
charging station returns to its normal operating state after the push-button has been reset.
Canceling the emergency stop state
Note
Eliminate the hazardous situation
First eliminate the hazardous situation. Only then can the emergency stop state be canceled.
The Emergency Stop button is equipped with a rotate-to-unlatch mechanism. An arrow on
the top of the button indicates the direction of rotation for unlatching.
Safety information
2.3Emergency Stop button
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
14 Operating Instructions, 10/2022, A5E50828019-AC

Unlatching the Emergency Stop button
To cancel the emergency stop state, proceed as follows:
• Turn the emergency stop button in the direction of the arrow until the push-button is
released.
The charging station will automatically start up. When the charging station display shows the
Start menu, the charging station is back in normal operating mode.
2.4 Safety sign
To handle the charging station safely, safety signs are attached to the charging station and the
packaging.
Safety signs on the packaging
The following safety signs are attached to the packaging of the charging station:
Safety sign Meaning
Marking of the center of gravity
Warning of tipping hazard
Identi󹪝cation of locations that cannot be used for pickup using a forklift
Safety sign on the charging station cabinet
The following safety signs are attached to the charging station cabinet:
Safety sign Meaning
Warning of general danger
Warning of dangerous voltage
Warning of tipping hazard
Safety information
2.4Safety sign
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 15

2.5 Cybersecurity at Siemens
SIEMENS AG provides products and solutions with cybersecurity functions that support the
secure operation of plants, systems, machines and networks.
Implement and maintain the cybersecurity concept
In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art cybersecurity concept.
Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Systems, machines, and components should only be connected
to the enterprise network or the Internet if and to the extent that it is necessary and with
appropriate security measures in place (e.g. using 󹪝rewalls and network segmentation).
In addition, the recommendations of Siemens regarding appropriate protective measures
should be observed. For more information about cybersecurity, please visit:
Cybersecurity at Siemens (https://www.siemens.com/cybersecurity#ouraspiration)
Only use current product versions
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Using versions that are obsolete or are no longer
supported can increase the risk of cyber threats.
2.6 Identi󹪝cation of the device
The nameplate clearly identi󹪝es the charging station. The nameplate also contains the
identi󹪝cation data of the device, the manufacturer and the CE marking.
Safety information
2.6Identi󹪝cation of the device
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
16 Operating Instructions, 10/2022, A5E50828019-AC

Information on the nameplate
You can 󹪝nd the following information on the nameplate of the charging station:
Figure2-2 Example: Nameplate SICHARGE UC 200
Position of the nameplate on the device
The nameplate is located on the left exterior of the device in the lower left corner of the cabinet.
Safety information
2.6Identi󹪝cation of the device
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
Operating Instructions, 10/2022, A5E50828019-AC 17

Safety information
2.6Identi󹪝cation of the device
SICHARGE UC 100, UC 200, UC 300, UC 400, UC 600, UC 800
18 Operating Instructions, 10/2022, A5E50828019-AC