Siemens TCF2 User manual

Hazardous voltage.
Will cause death or
serious injury.
Turn OFF and lock out all
power supplying this
device before installing
or servicing accessory.
Siemens Energy & Automation, Inc.
Bellefontaine, Ohio 43311 U.S.A.
Installation Instructions
Item: Instructions for Installation of Circuit Breaker
Plug-InAdapters. Cat.No.’sTCF2
(2-Pole)andTCF3(3-Pole).
For use with: SIEMENS® FD Frame Circuit Break-
ers and Molded Case Switches in conjunction with
plug-in-tulip connector assemblies. Cat. No.’s
PC4753, PC4754 and PM4754
Page 1 of 3
Pc. No. 410902A01
BREAKERS TYPES
FJ6(ETI), F6, HF6, FM6, FMK, CLF(ETI), HFJ6,
(H)(H)FXD6(ETI),FD6,(H)(H)FD6,CFD6(ETI),FFC,FFF
SAFETY INSTRUCTIONS
Fig. 4
InstallAs Shown
NOTE: Thisinstructionoutlinestherecommended
installation procedure.
1. Circuit Breaker Preparation
The circuit breaker should be in the OFF/”O”
positionbefore installing theplug-in-tulipadapter
kit. Turn off and lock out all power supplying
this device before installing. Verify that
NO volt-
age is present before proceeding with task.
Remove Pressure Wire Connectors From
Breaker If Present
2. Place tulip clip assembly (6) on back of breaker
in recess provided in base molding. Secure in
place with 5/16 flatwashers (7), lockwashers (8)
and 5/16 - 18 X 1 1/2 round head screws (9)
furnished. (Exception - on CLF and CFD break-
ers use 2” long screws on load side.) Torque
screws to 5-6 lb-Ft. [6.78-8.13 N/m] to assure a
good electrical connection. Repeat this proce-
dure for the remaining tulip clip assemblies.
3. Slide upper end shields (10) and insert lower
endshields(11)withbeveledendfacing breaker
and press into slots provided at line and load
end of breaker.
4. Add accessory label (12) to top of breaker as
indicated in Fig. 4.

Siemens Energy & Automation, Inc.
Bellefontaine, OH 43311 U.S.A.
Installation Instructions
Hazardous voltage.
Will cause death or
severe injury.
Turn OFF and lock out all
power supplying this
device before installing or
servicing accessory.
TCF2
TCF3
5.00-6.00 Ft.-lbs.
6.78-8.13 N/m
4 x 11
4 x 10
1 x 12
4 x 6
1.50”
1 x 12
6 x 6
4 x 8
4 x 7
4 x 9a
6 x 11
6 x 10
6 x 7
6 x 8
6 x 9a
1.50”
FJ6(ETI), F6, FM6, FMK,
HF6,HFJ6(H)(H)FXD(ETI),
FD6, (H)(H)FD6, FFC, FFF
Page 2 of 3
Pc. No. 410902A01

Siemens Energy & Automation, Inc.
Bellefontaine, OH 43311 U.S.A.
Installation Instructions
Hazardous voltage.
Will cause death or
severe injury.
Turn OFF and lock out all
power supplying this
device before installing or
servicing accessory.
Page 3 of 3
Pc. No. 410902A01
© Siemens Energy & Automation, Inc.
5.00-6.00 Ft.-lbs.
6.78-8.13 N/m
CLF(ETI)
CFD6(ETI)
TCF3
TCF2
1 x 12
6 x 6
4 x 6
1 x 12
6 x 8
2.00”
4 x 7
1.50”
2 x 9a
4 x 10
4x 11
4 x 8
2 x 9b
2.00”
3 x 9b
6 x 7
1.50”
3 x 9a
6 x 10
6 x 11