Siemens VBI60.15-5L User manual

CE1N4213en
Smart Infrastructure
2020-02-20
ACVATIX™
2-port shutoff valves and 3-port changeover ball valves, PN 40,
with internally threaded connection
VAI60.., VBI60..L, VBI60..T
VAI60.. VBI60..L VBI60..T
For use in heating, ventilation, and air conditioning plants as shutoff or change-
over ball valve. In closed circuits.
●Ball valve body made of brass, UNS C35330 (DZR)
●DN 15...50
●kvs 5…96 m3/h
●Connections with internal threading Rp per ISO 7-1
●Rotational angle 90°
●Can be used with electromotorized rotary actuators GQD..9A, GMA..9E with
spring return and GSD..9A, GDB..9E, GLB..9E without spring return

2
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Features
●Moderately price:
Optimized flow rates mean smaller ball valves can be selected. Low torque means you
can combine them with small, less expensive rotary actuators.
●Long life expectancy:
Maintenance-free construction, also thanks to low friction stem and polished ball made of
chrome-plated DZR brass.
●Simple mounting:
The brackets, premounted on the actuators, means you can mount them on the ball
valves without tools.
Technical design
Design
1
Housing
2
Internally threaded connection
3
Seat
4
O-ring seal
5
Marble
6
Stem, squared
7
Slide clutch
8
O-ring seal

3
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Sizing
Flow diagram:
5
Low noise operation
9
200
300
400
55,6
83
111
1516
2225
1213
3537
49
6873
96
---
Δpmax for VAI60.. and VBI60.., for details, see table on equipment
combinations
Δpmax
=
Maximum permissible differential pressure over the ball valve, valid for the
entire positioning range of the ball valve rotary actuator unit; if low noise
operation is desired, we recommend a maximum permissible differential
pressure of 200 kPa
Δpv100
=
Differential pressure over the fully opened ball valve and over the control
path at a volume flow V100
100
=
Volume flow through the fully opened ball valve
100 kPa
=
1 bar ≈ 10 mWS
1 m3/h
=
0.278 l/s water at 20 °C

4
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Cavitation
Cavitation increases wear and tear of the ball and seat and results in unwanted noise.
Cavitation can be prevented by not exceeding the differential pressures as per the flow
diagram and maintaining the static pressures depicted below.
Δpmax
=
Differential pressure at a nearly closed ball valve
to largely avoid cavitation
p1
=
Static pressure at the ball valve inlet
P3
=
Static pressure at the ball valve outlet
M
Pump
J
Water temperature
Example with hot water:
Pressure p1at ball valve inlet: 500 kPa (5 bar)
Water temperature: 120 °C
The above diagram clearly indicates that the maximum permissible differential pressure is
Δpmax → 200 kPa (2 bar) at a nearly closed ball valve.
Note on chilled water applications
To prevent cavitation in chilled water circuits, sufficient counter pressure must be supplied to
the ball valve outlet, e.g. using an additional butterfly valve downstream of the ball valve.
Maximum permissible differential pressure over the ball valve: See 80 °C curve in the above
diagram.

5
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Operating pressure and operating temperature
Liquids:
Operating pressure and medium temperature per IS0 7005
(Observe all local and applicable laws).
Type summary
Type
DN
kvs
Shutoff ball valve 2-port
3-port changeover valve (L)
3-port changeover valve (T)
[m3/h]
–
VBI60.15-5L
-
15
5
–
–
VBI60.15-12T
12 1)
VAI60.15-15
–
–
15
–
VBI60.20-9L
–
20
9
–
–
VBI60.20-16T
16 1)
VAI60.20-22
–
–
22
–
VBI60.25-9L
–
25
9
–
–
VBI60.25-16T
16 1)
VAI60.25-22
–
–
22
–
VBI60.32-13L
–
32
13
–
–
VBI60.32-25T
25 1)
VAI60.32-35
–
–
35
–
VBI60.40-25L
–
40
25
–
–
VBI60.40-49T
49 1)
VAI60.40-68
–
–
68
–
VBI60.50-37L
–
50
37
–
–
VBI60.50-73T
73 1)
VAI60.50-96
–
–
96
1) kvs Bypass B > 50 % of kvs A ─ AB
DN
=
Nominal size
kvs
=
Flow nominal value for chilled water (5…30 °C) through a fully opened ball valve at a
differential pressure of 100 kPa (1 bar)

6
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Accessories
Insulation shells
Insulation shells are available for heating/cooling insulation as a separate accessory:
Type
Material
Density
Thermal conductivity at tm 40 °C
Operating
temperature
ALI..V..G..
Polyethylene foam
29 kg/m3
0.0372 W/mK
-10 °C…100 °C
For 2-port shutoff ball valves
For 3-port changeover valves
Ball valve
Insulation shell
Ball valve
Insulation shell
VAI60.15..
ALI15VAI60/61
VBI60.15..
ALI15VBI60/61
VAI60.20..
ALI20VAI60/61
VBI60.20..
ALI20VBI60
VAI60.25..
ALI25VAI60/61
VBI60.25..
ALI25VBI60/61
VAI60.32..
ALI32VAI60/61
VBI60.32..
ALI32VBI60/61
VAI60.40..
ALI40VAI60/61
VBI60.40..
ALI40VBI60/61
VAI60.50..
ALI50VAI60/61
VBI60.50..
ALI50VBI60/61
Insulation shells for shutoff and changeover ball valves
ALI..VAI..
ALI..VBI..
For dimensions, see Section Dimensions [➙13]
Filter
Installed upstream of the ball valve:
Type
Stock number
Description
DN
Mesh width [mm]
ALX15
S55845-Z174
Filter with internal threading
15
0.5
ALX20
S55845-Z175
Filter with internal threading
20
0.8
ALX25
S55845-Z176
Filter with internal threading
25
0.8
ALX32
S55845-Z177
Filter with internal threading
32
0.8
ALX40
S55845-Z178
Filter with internal threading
40
0.8
ALX50
S55845-Z179
Filter with internal threading
50
0.8

7
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Equipment combinations
Type
Rotary actuators
GSD..9A
GQD..9A
GDB..9E
GMA..9E
GLB..9E
Δpmax
Δps
Δpmax
Δps
Δpmax
Δps
Δpmax
Δps
Δpmax
Δps
Ball valve
[kPa]
VAI60.15-15
350
1400
350
1400
350
1400
350
1400
350
1400
VAI60.20-22
VAI60.25-22
VAI60.32-35
-
-
-
-
-
-
1000
1000
VAI60.40-68
800
800
VAI60.50-96
600
600
VBI60.15-5L
350
350
350
-
350
-
350
-
VBI60.20-9L
VBI60.25-9L
VBI60.32-13L
-
-
-
VBI60.40-25L
VBI60.50-37L
VBI60.15-12T
350
350
350
350
VBI60.20-16T
VBI60.25-16T
VBI60.32-25T
-
-
-
VBI60.40-49T
VBI60.50-73T
Δpmax
=
Maximum permissible differential pressure over the valve ball control path, valid for the entire
positioning range of the ball valve rotary actuator unit; if low noise operation is desired, we
recommend a differential pressure of 200 kPa
Δps
=
Maximum permissible differential pressure (closing pressure) at which the ball valve rotary actuator
unit securely closes against the pressure
Overview of rotary actuators for ball valves
Type 1)
Operating
voltage
Positioning
Spring return
Data sheet
Signal
Time
Function
Time
GSD141.9A
AC/DC 24 V
Open-close 2)
30 s
-
-
N4655
GSD341.9A
AC 230 V
GQD121.9A
AC/DC 24 V
2-position
30/15 s 3)
Yes
15 s
N4659
GQD321.9A
AC 230 V
GMA121.9E
AC/DC 24 V
90/15 s 3)
N4658
GMA321.9E
AC 230 V
GLB131.9E 4)
AC 24 V
(2) 3-position
150 s
-
-
N4657
GLB331.9E 4)
AC 230 V
GLB141.9E
AC/DC 24 V
2 or 3 point
A6V10636203
GLB341.9E
AC 100-240 V
GDB111.9E/KN
AC 24 V
KNX-TP
150/120 s
A6V10881143
GLB111.9E/MO
AC 24 V
Modbus RTU
A6V10725318
GDB141.9E
AC/DC 24 V
2 or 3 point
150 s
A6V10636150
GDB341.9E
AC 100...240 V
1)
Actuator type: Electromotive
3)
Open/close
2)
2-wire SPDT (single pole double throw)
4)
While stock lasts

8
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Ordering
Please indicate material, article type, order text, and quantity; example:
Material
Article type
Order text
Quantity
VAI60.25-22
VAI60.25-22
Open/close ball valve internally threaded, 2-port
2
GLB131.9E
GLB131.9E
Actuator for ball valve, NSR
2
Delivery
Ball valves, rotary actuators, and mounting kits are not assembled and are delivered in
individual packaging.
Applications with auxiliary functions
A standard actuator with corresponding functionality can be used if a ball valve application
requires a rotary actuator with auxiliary functions (e.g. auxiliary switch or potentiometer). In
this case, mounting kit ASK77.x is required in addition to the rotary actuator.
Follow the mounting instructions when mounting.
Rotary actuator
Options
Order text: Mounting kit
GMA..1E
(with spring return)
Potentiometer, auxiliary switch
ASK77.2 Accessory Kit BV for GMA..1.9E
GLB..1E
(without spring return)
ASK77.3 Accessory Kit BV for GLB..1.9E
GDB..1E
(without spring return)
ASK77.3 Accessory Kit BV for GDB..1.9E
GQD..1A
(with spring return)
Auxiliary switch
ASK77.5 Accessory Kit BV for GQD..1.9A
GSD..1A 1)
(without spring return)
ASK77.5 Accessory Kit BV for GSD..1.9A
1)
GSDx4x.1A are not compatible with ball valves.
Product documentation
Title
Content
Document ID
Mounting instructions Ball valve VAI60.. ,
VBI60..L, VBI60..T
Mounting instructions
M4213
(74 319 0883 0)
Rotary actuators for ball valves GSD..41.9A
Data sheet: product description
N4655
Rotary actuators for ball valves GQD..9A
Data sheet: product description
N4659
Rotary actuators for ball valves GMA..9E
Data sheet: product description
N4658
Rotary actuators for ball valves GDB..9E, GLB..9E
Data sheet: product description
N4657
Rotary actuators for ball valves GLB..9E
Data sheet: product description
A6V10636203
Rotary actuators for ball valves GDB..9E
Data sheet: product description
A6V10636150
Mounting instructions Mounting kit ASK77.2,
ASK77.3
Mounting instructions
M4696
(74 319 0648 0)
Mounting instructions Mounting kit ASK77.5
Mounting instructions
A6V11171911
(A5W00032790)
Related documents such as environmental declarations, CE declarations, etc., can be
downloaded at the following Internet address:
http://siemens.com/bt/download

9
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Notes
Safety
DANGER
There is a risk to operating personnel and device when working on the unit
Failure to comply with these safety notes can result in personal injury and damage to
property from pipe pressure, electrical voltage, or device in operation.
Note the following when servicing a ball valve/rotary actuator:
●Switch off both pump and operating voltage.
●Close shutoff valves.
●Release pressure in the pipes and allow them to cool down completely.
●Disconnect electrical connections from the terminals as needed.
●The rotary actuator must be properly installed prior to recommissioning the ball valve.
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
Engineering
We recommend installing the ball valve with spring return since temperatures are lower on
heating plants which increases the lifespan of the sealing gland on the stem.
Ensure there is no cavitation (see Section Technical design [➙2]).
A filter must be installed upstream of the ball valve to increase functional safety.
Permissible media
Using the ball valve together with potassium formate-based media can result in leakage over
the stem to the outside. The reason is the high level of penetration at low surface tension of
media based on potassium formate.
Siemens rejects any and all liability for damages or consequential damages resulting from
the use of this media together with our ball valves.
Mounting
It is easy to assemble the ball valve and rotary actuator; it can be done at the construction
site. No special tools or settings required.
Ball valve VAI60.. / VBI60.. is supplied together with mounting instructions M4213
(74°319°0883°0).

10
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Mounting position
VAI60..
VBI60..
Pipe connection
Avoid leakage:
●Install fittings as per ISO 7-1. Ball valves (internal threading) = "Rp";
Piping (external threading) = "R".
●Do not use too much hemp or PTFE tape.
●Do not tighten pipe threading to the very end.
●Place the pliers/wrench on the ball valve union nut that is closer to the pipe to be
tightened or loosened.
Flow direction
Make sure that the valve is mounted in the proper flow direction. A symbol is applied to the
ball valve body:
VAI60..
VBI60..
Ball valve
Laser marking
Position as delivered
90 ° turned (clockwise)
VAI60..
2-port shutoff ball
valve
-
AAB
4213Z01
AAB
4213Z02
A –AB = 100 %
A –AB = 0 %
VBI60..L
3-port
changeover ball
valve with L
shaped
B
AAB
4213Z03
A
B
AAB
4213Z04
B –AB (AB –B) = 100 %
A –B (B –A) = 100 %
VBI60..T
3-port
changeover ball
valve with T
shaped
AAB
B
4213Z13
B
AAB
4214Z27
B
AAB
4214Z28
A –AB = 100 %
B –AB = 0 %
A –AB = 0 %
B –AB = 100 %

11
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Maintenance
Ball valves VAI60.. and VBI60.. are maintenance free.
Disposal
Do not dispose of the device as part of domestic waste.
●Special handling of individual components may be required by law or make ecological
sense.
●Adhere to all local and currently applicable laws and regulations.
Warranty
Technical data on specific applications are valid only together with Siemens products listed
under "Equipment combinations". Siemens rejects any and all warranties in the event that
third-party products are used.

12
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Technical data
Functional data
VAI60..
VBI60..L
VBI60..T
PN class
PN 40 per ISO 7268
Operating pressure
Per ISO 7005 within the permissible media temperature as per Section Technical
design [➙2]
Leakage through-port
Water proof per EN 60534-
4 L/1, improved class 5
-
Water proof per EN 60534-
4 L/1, improved class 4
Leakage A (Flow B-AB)
Leakage AB (Flow A-B)
-
Water proof per EN 60534-
4 L/1, improved class 4
-
Leagage bypass
-
-
< 1 %
Permissible media
Chilled water, low temperature hot water, hot water, water with antifreeze.
Recommendation: Water treatment per VDI 2035
Note: Page 9
Medium temperature
-10…120 °C
Rangeability Sv
> 500
Rotational angle
90 °
Materials
Ball valve body
Dezincification-resistant hot-pressed brass (DZR 1)), CW602N
Marble
Dezincification-resistant hot-pressed brass (DZR 1)), CW602N, chrome
plated
Stem
Dezincification-resistant hot-pressed brass (DZR 1)), CW602N
Sealing gland
EPDM-O rings
Dimensions / Weight
See Dimensions [➙13]
Internally threaded connection
Rp per ISO 7-1
Standards, directives and approvals
Pressure Equipment Directive
DGR 2014/68/EU
Pressure accessories
Fluid group 2
Range: Article 1, para. 1
Definition: Article 2, para. 5
Without CE certification as per article 3, para. 3
(generally applicable engineering practice) 2)
EAC compliance
Eurasian compliance
Environmental compatibility
Environmental Declaration E1E4213en 3) contains data on environmental-
compatible product design and assessment (RoHS compliance,
compositions, packaging, environmental benefits and disposal).
1)
Dezincification resistant
2)
Fittings for a product where PS x DN < 1000, do not require special testing and cannot have CE labeling
3)
See Section Product documentation [➙8]

13
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Dimensions
VAI60..
4213M01
DN
=
Nominal size
H
=
Total height of actuator plus minimum mounting distance to wall or ceiling, for mounting, connection,
operation, maintenance, etc.
H1
=
Dimension from the pipe to the center to install actuator (upper edge)
Type
DN
B
C
D
Rp
L1
L2
H1
H2
[mm]
[inch]
[mm]
VAI60.15-15
15
26
31 1)
42
Rp ½
30.8
61.6
27.6
37.6
VAI60.20-22
20
31
38
42
Rp ¾
33,5
67
30.5
40.5
VAI60.25-22
25
39
42.5
42
Rp 1
38.4
76.8
30.5
40.5
VAI60.32-35
32
48
52
42
Rp 1¼
44
88
34.3
44.3
VAI60.40-68
40
55
61
42
Rp 1½
50.9
101.8
39.8
49.8
VAI60.50-96
50
67
74
42
Rp 2
58.1
116.2
52.8
62.8
1)
Ball valve body extends above threaded connection
Type
H
Weight
GSD..9A
GQD..9A
GDB..9E
GMA..9E
GLB..9E
[mm]
[kg]
VAI60.15-15
> 300
> 300
> 300
> 300
> 300
0.28
VAI60.20-22
0.36
VAI60.25-22
> 320
> 320
> 320
> 320
> 320
0.46
VAI60.32-35
-
-
-
0.7
VAI60.40-68
1.1
VAI60.50-96
> 335
> 335
1.74

14
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
VBI60..L / VBI60..T
4213M02
DN
=
Nominal size
H
=
Total height of actuator plus minimum mounting distance to wall or ceiling, for mounting, connection,
operation, maintenance, etc.
H1
=
Dimension from the pipe to the center to install actuator (upper edge)
Type
DN
B
C
C1
D
Rp
L1
L2
H1
H2
[mm]
[inch]
[mm]
VBI60.15-5L
15
26
34
49.5
42
Rp ½
33.3
66.6
27.6
37.6
VBI60.20-9L
20
39
39.8
61.05
42
Rp ¾
40.2
80.4
30.5
40.5
VBI60.25-9L
25
39
44.8
66.5
42
Rp 1
42.7
85.4
30.5
40.5
VBI60.32-13L
32
48
52.6
78.6
42
Rp 1¼
49.6
99.2
34.3
44.3
VBI60.40-25L
40
55
57.1
87.6
42
Rp 1½
54.8
109.6
39.8
49.8
VBI60.50-37L
50
67
68.9
105.9
42
Rp 2
65.7
131.4
52.8
62.8
VBI60.15-12T
15
26
34
49.5
42
Rp ½
33.3
66.6
27.6
37.6
VBI60.20-16T
20
39
39.8
61.05
42
Rp ¾
40.2
80.4
30.5
40.5
VBI60.25-16T
25
39
44.8
66.5
42
Rp 1
42.7
85.4
30.5
40.5
VBI60.32-25T
32
48
52.6
78.6
42
Rp 1¼
49.6
99.2
34.3
44.3
VBI60.40-49T
40
55
57.1
87.6
42
Rp 1½
54.8
109.6
39.8
49.8
VBI60.50-73T
50
67
68.9
105.9
42
Rp 2
65.7
131.4
52.8
62.8
Type
H
Weight
GSD..9A
GQD..9A
GDB..9E
GMA..9E
GLB..9E
[mm]
[kg]
VBI60.15-5L
> 300
> 300
> 300
> 300
> 300
0.32
VBI60.20-9L
0.73
VBI60.25-9L
> 320
> 320
> 320
> 320
> 320
0.62
VBI60.32-13L
-
-
-
0.97
VBI60.40-25L
1.43
VBI60.50-37L
> 335
> 335
2.36
VBI60.15-12T
> 300
> 300
> 300
> 300
> 300
0.31
VBI60.20-16T
0.74
VBI60.25-16T
> 320
> 320
> 320
> 320
> 320
0.63
VBI60.32-25T
-
-
-
0.69
VBI60.40-49T
1.38
VBI60.50-73T
> 335
> 335
2.26

15
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Insulation shells for 2-port shutoff ball valves (VAI60..)
L
D1
D
B
Ø 67
C
E
4213M03
DN
=
Nominal size
H
=
Total height of actuator plus minimum mounting distance to wall or ceiling, for mounting, connection,
operation, maintenance, etc.
Type
DN
B
C
D
D1
E
L
Insulation shell
For ball valve
[mm]
ALI15VAI60/61
VAI60.15-15
15
56
95
65
27
21
100
ALI20VAI60
VAI60.20-22
20
56
95
66
32
27
105
ALI25VAI60/61
VAI60.25-22
25
56
95
80
37
34
108
ALI32VAI60/61
VAI60.32-35
32
86
100
95
47
43
130
ALI40VAI60/61
VAI60.40-68
40
95
102
98
50
48
140
ALI50VAI60/61
VAI60.50-96
50
105
96
110
56
61
160
Type
H
Weight
GSD..9A
GQD..9A
GDB..9E
GMA..9E
GLB..9E
Insulation shell
For ball valve
[mm]
[g]
ALI15VAI60/61
VAI60.15-15
> 300
> 300
> 300
> 300
> 300
15
ALI20VAI60
VAI60.20-22
16
ALI25VAI60/61
VAI60.25-22
> 320
> 320
> 320
> 320
> 320
20
ALI32VAI60/61
VAI60.32-35
-
-
-
28
ALI40VAI60/61
VAI60.40-68
32
ALI50VAI60/61
VAI60.50-96
> 335
> 335
36

16
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Insulation shells for 3-port changeover ball valves (VBI60..)
D
D1
67Ø
LC1
C
E
H
4213M04
DN
=
Nominal size
H
=
Total height of actuator plus minimum mounting distance to wall or ceiling, for mounting, connection,
operation, maintenance, etc.
Type
DN
C
C1
D
D1
E
L
Insulation shell
For ball valve
[mm]
ALI15VBI60/61
VBI60.15..
15
100
50
70
34
21
100
ALI20VBI60
VBI60.20..
20
115
55
80
40
27
120
ALI25VBI60/61
VBI60.25..
25
115
55
80
40
34
120
ALI32VBI60/61
VBI60.32..
32
125
55
95
45
43
150
ALI40VBI60/61
VBI60.40..
40
125
55
95
45
48
150
ALI50VBI60/61
VBI60.50..
50
145
60
110
54
61
170
Type
H
Weight
GSD..9A
GQD..9A
GDB..9E
GMA..9E
GLB..9E
Insulation shell
For ball valve
[mm]
[g]
ALI15VBI60/61
VBI60.15..
> 300
> 300
> 300
> 300
> 300
21
ALI20VBI60
VBI60.20..
30
ALI25VBI60/61
VBI60.25..
> 320
> 320
> 320
> 320
> 320
30
ALI32VBI60/61
VBI60.32..
-
-
-
41
ALI40VBI60/61
VBI60.40..
43
ALI50VBI60/61
VBI60.50..
> 335
> 335
51

17
Siemens CE1N4213en
Smart Infrastructure 2020-02-20
Filter
4212M03
Type
DN
b
c
G
L
H
kvs
Weight
mm
Inch 1)
mm
kg
ALX15
15
12
38
G ½
54
27
3.5
0.178
ALX20
20
15
43
G ¾
67
34
5.8
0.290
ALX25
25
16
53
G 1
79
41
9.1
0.410
ALX32
31
17
64
G 1¼
98
51
19
0.680
ALX40
40
18
70
G 1½
106
57
24
0.874
ALX50
50
20
85
G 2
122
69
36
1.428
1) ISO 228-1

Unrestricted18
Siemens
CE1N4213en
Smart Infrastructure
2020-02-20
Issued by
Siemens Switzerland Ltd
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. [phone]
www.siemens.com/buildingtechnologies
© Siemens Switzerland Ltd, 2010
Technical specifications and availability subject to change without notice.
Document ID
CE1N4213en
Edition
2020-02-14
Revision numbers
Type
Valid from
rev. no.
Type
Valid from
rev. no.
Type
Valid from
rev. no.
Shutoff ball valve
VAI60..
Changeover ball
valve VBI60..L
Changeover ball
valve VBI60..T
2-port
3-port
3-port
VAI60.15-15
..A
VBI60.15-5L
..A
VBI60.15-12T
..A
VAI60.20-22
..A
VBI60.20-9L
..A
VBI60.20-16T
..A
VAI60.25-22
..A
VBI60.25-9L
..A
VBI60.25-16T
..A
VAI60.32-35
..A
VBI60.32-13L
..A
VBI60.32-25T
..A
VAI60.40-68
..A
VBI60.40-25L
..A
VBI60.40-49T
..A
VAI60.50-96
..A
VBI60.50-37L
..A
VBI60.50-73T
..A