Siemens BT300 LonWorks Instructions for use

www.sbt.siemens.com
Siemens BT300
HVAC Drive
Application Manual
Revision A

Siemens Industry, Inc. • 1
24-hour support [phone] (Dial 2)
table of contents
Document ID:DPD01149B
Rev. B
Revision release date: February 12, 2013
1. Siemens BT300 - Startup..................................................................................3
1.1 Startup Wizard ............................................................................................................................. 3
1.2 PID Mini-Wizard ........................................................................................................................... 4
1.3 Multi-pump mini-wizard ................................................................................................................ 5
2. Keypad of the drive...........................................................................................7
2.1 Siemens keypad with graphical display ....................................................................................... 8
2.1.1 Keypad display ............................................................................................................................ 8
2.1.2 Using the graphical keypad ......................................................................................................... 8
2.2 Menu structure ........................................................................................................................... 13
2.2.1 Quick setup................................................................................................................................ 13
2.2.2 Monitor....................................................................................................................................... 13
2.2.3 Parameters ................................................................................................................................ 14
2.2.4 Diagnostics ................................................................................................................................ 14
2.2.5 I/O and hardware ....................................................................................................................... 16
2.2.6 User settings.............................................................................................................................. 19
2.2.7 Favorites .................................................................................................................................... 20
2.2.8 User levels ................................................................................................................................. 20
3. Siemens Application.......................................................................................21
3.1 Specific functions of the Siemens application............................................................................ 21
3.2 Example of control connections................................................................................................. 22
3.3 Application - Quick setup parameter group................................................................................ 23
3.4 Monitor group............................................................................................................................. 24
3.4.1 Multi-monitor .............................................................................................................................. 24
3.4.2 Basic .......................................................................................................................................... 25
3.4.3 Timer functions monitoring ........................................................................................................ 26
3.4.4 PID1 controller monitoring ......................................................................................................... 27
3.4.5 PID2 controller monitoring ......................................................................................................... 27
3.4.6 Multi-pump monitoring ............................................................................................................... 27
3.4.7 Fieldbus data monitoring ........................................................................................................... 28
3.4.8 Temperature inputs monitoring.................................................................................................. 29
3.5 Application parameter lists......................................................................................................... 30
3.5.1 Parameter programming............................................................................................................ 31
3.5.2 Column explanations ................................................................................................................. 33
3.5.3 Group 3.1: Motor settings .......................................................................................................... 34
3.5.4 Group 3.2: Start/Stop setup ....................................................................................................... 35
3.5.5 Group 3.3: Control reference settings........................................................................................ 37
3.5.6 Group 3.4: Ramp & Brakes Setup .............................................................................................39
3.5.7 Group 3.5: I/O Configuration...................................................................................................... 40
3.5.8 Group 3.6: Fieldbus Data Mapping............................................................................................ 46
3.5.9 Group 3.7: Prohibited Frequencies............................................................................................ 47
3.5.10 Group 3.8: Limit supervisions .................................................................................................... 48
3.5.11 Group 3.9: Protections............................................................................................................... 49
3.5.12 Group 3.10: Automatic reset...................................................................................................... 52
3.5.13 Group 3.11: Timer functions ...................................................................................................... 53
3.5.14 Group 3.12: PID-controller 1...................................................................................................... 57
3.5.15 Group 3.13: PID-controller 2...................................................................................................... 64
3.5.16 Group 3.14: Multi-pump ............................................................................................................. 69
3.5.17 Group 3.16: Fire mode............................................................................................................... 70
3.5.18 Group 3.17: Application settings................................................................................................ 70
3.6 HVAC Application - Additional parameter information ............................................................... 71
3.7 Application - Fault tracing .......................................................................................................... 94

Siemens Industry, Inc. • 2
24-hour support [phone] (Dial 2)
3.7.1 Fault appears............................................................................................................................. 95
3.7.2 Fault history ............................................................................................................................... 95
3.7.3 Fault codes ................................................................................................................................ 96

Siemens BT300 - Startup Siemens Industry, Inc. • 3
24-hour support [phone] (Dial 2)
1. SIEMENS BT300 - STARTUP
1.1 Startup Wizard
In the Startup Wizard, you will be prompted for essential information needed by the drive so that it can
start controlling your process. In the Wizard, you will need the following keypad buttons:
Left/Right arrows. Use these to easily move between digits and decimals.
Up/Down arrows. Use these to move between options in menu and to change value.
OK button. Confirm selection with this button.
Back/Reset button. Pressing this button, you can return to the previous question in the
Wizard. If pressed at the first question, the Startup Wizard will be canceled.
Once you have connected power to your Siemens BT300 variable frequency drive, follow these instruc-
tions to easily set up your drive.
Push the OK button unless you want to set all parameter values manually.
1Language selection Depends on language package
2
Daylight saving*
* These questions appear if battery is installed.
Russia
US
EU
OFF
3Time* hh:mm:ss
4Day* dd.mm.
5Year* yyyy
6Run Startup Wizard? Yes
No
7Choose your process Pump
Fan
8Set value for Motor nominal speed
(according to nameplate)
Range: 24...19,200 rpm

Siemens Industry, Inc. • 4 Siemens BT300 - Startup
24-hour support [phone] (Dial 2)
Now the Startup Wizard is done.
The Startup Wizard can be re-initiated by activating the parameter Restore factory defaults
(par. P6.5.1) in the Parameter backup sub-menu (M6.5) OR with parameter P1.19 in the Quick setup
menu.
1.2 PID Mini-Wizard
The PID mini wizard is activated in the Quick Setup menu. This wizard presupposes that you are going
to use the PID controller in the "one feedback / one setpoint" mode. The control place will be I/O A and
the default process unit ‘%’.
The PID mini wizard asks for the following values to be set:
If any other process unit than ‘%’ is selected the following questions appear: If not the Wizard will directly
jump to step 5.
If one of the analog input signals is selected the question 6 appears. Otherwise you will be taken to step
7.
If one of the analog input signals is selected the question 9 appears. Otherwise you will be taken to
question 11.
If either of the options Keypad Setpoint 1 or 2 is chosen the step 10 will appear.
9Set value for Motor nominal current (ac-
cording to nameplate)
Range: Varies
10 Set value
for Minimum frequency Range: 0.00...60.00 Hz
11
Set value for Maximum frequency Range: 0.00...320.00 Hz
1Process unit selection (Several selections. See par. P3.12.1.4)
2Process unit min
3Process unit max
4Process unit decimals 0...4
5Feedback 1 source selection See page 67 for selections.
6Analog input signal range 0 = 0…10 V / 0…20 mA
1 = 2…10 V / 4…20 mA
See page 45.
7Error inversion 0 = Normal
1 = Inverted
8Setpoint source selection See page 61 for selections.
9Analog input signal range 0 = 0…10 V / 0…20 mA
1 = 2…10 V / 4…20 mA
See page 45.
10 Keypad setpoint

Siemens BT300 - Startup Siemens Industry, Inc. • 5
24-hour support [phone] (Dial 2)
If option ‘Yes’ is selected you will be prompted for three more values:
1.3 Multi-pump mini-wizard
The Multi-Pump mini-wizard asks the most important questions for setting up a Multi-Pump system. The
PID mini-wizard always precedes the Multi-Pump mini-wizard. The keypad will guide you through the
questions as in Chapter 1.2 then to be followed by the set of questions below:
If Auto-change function is enabled the following three questions will appear. If Auto-change will not be
used the Wizard jumps directly to question 11.
After this, the keypad will show the digital input and relay output configuration done by the
application. Write these values down for future reference.
11 Sleep function? No
Yes
12 Sleep frequency limit 1 0.00...320.00 Hz
13 Sleep delay 1 0...3000 s
14 Wake-up level 1 Range depends on selected process unit.
15 Number of motors 1...4
16 Interlock function 0 = Not used
1 = Enabled
17 Autochange 0 = Disabled
1 = Enabled
18 Include FC 0 = Disabled
1 = Enabled
19 Autochange interval 0.0...3000.0 h
20 Autochange: Frequency limit 0.00...60.00 Hz
21 Bandwidth 0...100%
22 Bandwidth delay 0...3600 s

Siemens Industry, Inc. • 6 Siemens BT300 - Startup
24-hour support [phone] (Dial 2)

Keypad of the drive Siemens Industry, Inc. • 7
24-hour support [phone] (Dial 2) 2
2. KEYPAD OF THE DRIVE
The control keypad with graphical interface is the interface between the Siemens BT300 variable fre-
quency drive and the user. With the control keypad it is possible to control the speed of a motor, to su-
pervise the state of the equipment and to set the variable frequency driver's parameters.
Figure 1. Keypad buttons.
Stop Button Start Button
Move Cursor
Move Cursor
Scroll Menu Up
Increase Value
Scroll Menu Down
Decrease Value
Enter Active Level/Item
Confirm Selection
Move Backward in Menu
Exit Edit Mode
Reset Faults with long Press
Left Right

Siemens Industry, Inc. • 8 Keypad of the drive
24-hour support [phone] (Dial 2)
2.1 Siemens keypad with graphical display
The graphical keypad features an LCD display and 9 buttons.
2.1.1 Keypad display
The keypad display indicates the status of the motor and the drive and any irregularities in motor or drive
functions. On the display, the user sees information about
his present location in the menu structure and
the item displayed.
See the attached Keypad Navigation Map to get a comprehensive idea of the menu structure.
2.1.1.1 Main menu
The data on the control keypad are arranged in menus and sub-menus. Use the Up and Down arrows
to move between the menus. Enter the group/item by pressing the OK button and
return to the previous
level by pressing the Back/Reset button.
The Location field indicates your current location. The Status field gives information about the present
status of the drive. See Figure 2.
Figure 2. Main menu.
2.1.2 Using the graphical keypad
2.1.2.1 Editing values
Change value of a parameter following the procedure below:
3. Locate the parameter.
4. Enter the Edit mode.
5. Set new value with the arrow buttons up/down. You can also move from digit to digit with the arrow
buttons left/right if the value is numerical and change then the value with the arrow buttons up/
down.
6. Confirm change with OK button or ignore change by returning to previous level with Back/Reset
button.
BT9159
(17)
(12)
STOP READY I/O
ID: M1
(5)
Main Menu
Quick Setup
Parameters
Monitor
Status field
Di re c t io n
Status field
Press OK to enter
Number of items
in the group
Location field
(Parameter ID number and
current menu location)
Control Place:
PC/IO/KEYPAD/FIELDBUS
STOP/RUN READY/NOT READY/FAULT
ALARM
Activated group/item:

Keypad of the drive Siemens Industry, Inc. • 9
24-hour support [phone] (Dial 2) 2
Figure 3. Editing values on graphical keypad.
2.1.2.2 Resetting fault
Instructions for how to reset a fault can be found in Chapter 3.7.1 on page 95.
2.1.2.3 Hand/Auto control button
The Hand/Auto button is used for two functions: to quickly access the Control page and to easily change
between the Hand (Keypad/Loc) and Auto control places.
Control places
The control place is the source of control where the drive can be started and stopped. Every control place
has its own parameter for selecting the frequency reference source. In the HVAC drive, the Hand control
place is always the keypad. The Auto control place is determined by parameter P1.15 (I/O or Fieldbus).
The selected control place can be seen on the status bar of the keypad.
Auto control place
I/O A, I/O B and Fieldbus can be used as Auto control places. I/O A and Fieldbus have the lowest priority
and can be chosen with parameter P3.2.1 (Ctrl. Place Auto). I/O B, again, can bypass the Auto control
place selected with parameter P3.2.1 using a digital input. The digital input is selected with parameter
P3.5.1.5 (I/O B Ctrl Force).
Hand control
The Keypad is always used as control place while in Hand control. Hand control has a higher priority
than the Auto control. Therefore, if, for example, bypassed by parameter P3.5.1.5 through digital input
while in Auto, the control place will still switch to Keypad if Hand is selected. Switching between Hand
and Auto Control can be done by pressing the HAND/AUTO button on the keypad or by using
the "Hand/Auto" (ID211) parameter.
Changing control places
Change of control place from Auto to Hand (keypad).
1. Anywhere in the menu structure, push the HAND/AUTO button.
2. Push the Arrow up or the Arrow down button to select HAND/AUTO and confirm with
the OK button.
3. On the next display, select Hand or Auto and again confirm with the OK button.
4. The display will return to the same location it was when the HAND/AUTO button was pushed.
However, if the Auto control place was changed to Hand (Keypad), you will be prompted for a
keypad reference.

STOP READY I/O
ID:172 M3.2.1

STOP READY I/O
ID: M3.2.1

STOP READY I/O
M3.2.1

STOP READY I/O
ID:172 M3.2.1

STOP READY I/O
M3.2.1
BT9160
BACK
RESET
OR:
Start/Stop Setup
Ctrl. Place Auto
I/O Control
KeypadStopButton
Yes
Start Function
Ramping
Edit
Help
Add to favorites
Ctrl. Place Auto Ctrl. Place Auto
I/O Control
FieldbusCTRL
Start/Stop Setup
Ctrl. Place Auto
I/O Control
KeypadStopButton
Yes
Start Function
Ramping
Ctrl. Place Auto
I/O Control
FieldbusCTRL

Siemens Industry, Inc. • 10 Keypad of the drive
24-hour support [phone] (Dial 2)
Figure 4. Changing control places.
Accessing the control page
The Control page is meant for easy operation and monitoring of the most essential values.
1. Anywhere in the menu structure, push the HAND/AUTO button.
2. Push the Arrow up or the Arrow down button to select Control page and confirm with
the OK button.
3. The control page displays.
If the keypad control place and the keypad reference are selected to be used, you can set the
Keypad reference after pressing the OK button. If other control places or reference values are
used, the display will show Frequency reference, which is not editable. The other values on the page
are Multi-monitoring values. You can choose which values display here for monitoring (for this pro-
cedure, see page 13).
Figure 5. Accessing the control page.
2.1.2.4 Copying parameters
The parameter copy function can be used to copy parameters from one drive to another.
The parameters are first saved to the keypad, then the keypad is detached and connected to another
drive. Finally the parameters are downloaded to the new drive restoring them from the keypad.
(21)


STOP READY Keypad
ID: M1
(12)

(6)
ID:
STOP Ready Keypad
ID:1805
?
ID:
STOP READY Keypad
ID:211
(21)


STOP READY I/O
ID: M1
(12)

(6)
BT11114
Main Menu
Parameters
Diagnostics
Monitor
Choose action
Hand/Auto
Control page
Change direction
Hand/Auto
Hand
Main Menu
Parameters
Diagnostics
Monitor
Auto
Hand
Auto
(21)


STOP READY I/O
ID: M1
(12)

(6)
ID:
STOP Ready Keypad
ID:1805
STOP READY Keypad
(6)
ID:168
0.00 Hz
0.00Hz
0.00A
0.00%
0.00%
BT11115
Main Menu
Parameters
Diagnostics
Monitor
Choose action
Hand/Auto
Control page
Change direction
Keypad Reference
Output Frequency
Motor Current
Motor Torque
Motor Power
STOP READY Keypad
(6)
0.00 Hz
0.00Hz
0.00A
0.00%
0.00%
ID:184
0.00 Hz
0.00Hz
0.00A
0.00%
0.00%
Keypad Reference
Output Frequency
Motor Current
Motor Torque
Motor Power
?
ID:
STOP READY Keypad
ID:211
Hand/Auto
Hand
Auto
Hand
Auto

Keypad of the drive Siemens Industry, Inc. • 11
24-hour support [phone] (Dial 2) 2
Before any parameters can successfully be copied from one drive to another, the drive has to be stopped
when the parameters are downloaded.
• First go into User settings menu and locate the Parameter backup sub-menu.
In the Parameter backup sub-menu, there are three possible functions to be selected:
•Restore factory defaults will re-establish the parameter settings originally made
at the factory.
• By selecting Save to keypad you can copy all parameters to the keypad.
•Restore from keypad will copy all parameters from the keypad to a drive.
Figure 6. Parameter copy.
NOTE: If the keypad is changed between drives of different sizes, the copied values of these parame-
ters will not be used:
Motor nominal current (P3.1.1.4)
Motor nominal voltage (P3.1.1.1)
Motor nominal speed (P3.1.1.3)
Motor nominal power (P3.1.1.6)
Motor nominal frequency (P3.1.1.2)
Motor cos phii (P3.1.1.5)
Switching frequency (P3.1.2.1)
Motor current limit (P3.1.1.7)
Stall current limit (P3.9.12)
Stall time limit (P3.9.13)
Stall frequency (P3.9.14)
Maximum frequency (P3.3.2)
2.1.2.5 Help
The graphical keypad features instant help, and information displays for various items.
All parameters offer an instant help display. Select Help and press the OK button.
Text information is also available for faults, alarms and the startup wizard.
Figure 7. Help text example.
STOP READY Keypad



(0)
(4)
ID: M6
(8)

STOP READY Keypad


(3)
ID: M6.5M6.5
STOP READY Keypad

ID: M6.5M6.5.1
BT11088
Main Menu
Favourites
User settings
I/O and Hardware
Drive name
User settings
Application selection
HVAC
Parameter backup
Drive Restore from keypad
Restore factory defaults
Save to keypad
Parameter backup
(6)

STOP READY I/O
ID:403 M3.5.1.1
(6)

STOP READY I/O
ID:403 M3.5.1.1
STOP READY I/O
ID:403 M3.5.1.1
BT9165
Digital Inputs
Ctrl Signal 1 A
Ctrl Signal 1 B
Ctrl Signal 2 A
Add to favorites
Ctrl signal 1 A
Edit
Help
Start Signal 1 for control Place
I/O A. Start Signal 1
functionality chosen with I/O A
Logic in Start/Stop Setup Menu.
Ctrl signal 1 A

Siemens Industry, Inc. • 12 Keypad of the drive
24-hour support [phone] (Dial 2)
2.1.2.6 Adding an item to Favorites
You might need to refer to certain parameter values or other items often. Instead of locating them one
by one in the menu structure, you may want to add them to a folder called Favorites,where they can
easily be reached.
To remove an item from the Favorites, see Chapter 2.2.7.
Figure 8. Adding item to Favorites.

230.00 V
1430 rpm
STOP READY I/O
50.00 Hz
STOP READY I/O STOP READY I/O
BT9166
Basic Settings
Motor Nom Voltg
Motor Nom Speed
Motor Nom Freq
Edit
Help
Motor Nom Freq
Add to favorites
Motor Nom Freq
was added to
favorites. Press OK
to continue.

Keypad of the drive Siemens Industry, Inc. • 13
24-hour support [phone] (Dial 2) 2
2.2 Menu structure
2.2.1 Quick setup
The Quick Setup Menu includes the minimum set of most commonly used parameters during installation
and commissioning. You can find more detailed information on the parameters of this group in
Chapter 3.3.
2.2.2 Monitor
Multi-monitor
On the multi-monitor page, you can collect nine values that you wish to monitor.
Figure 9. Multi-monitoring page.
Change the monitored value by activating the value cell (with arrow buttons left/right) and clicking OK.
Then choose a new item on the Monitoring values list and click OK again.
Basic
The basic monitoring values are the actual values of selected parameters and signals as well as statuses
and measurements. Different applications may have different statuses and different number of monitor-
ing values.
Timer functions
Monitoring of timer functions and the Real Time Clock. See Chapter 3.4.3.
PID Controller 1
Monitoring of PID controller values. See Chapter 3.4.4 and Chapter 3.4.5.
PID Controller 2
Monitoring of PID controller values. See Chapter 3.4.4 and Chapter 3.4.5.
Multi-Pump
Monitoring of values related to the use of several drives. See Chapter 3.4.6.
Fieldbus data
Fieldbus data shown as monitor values for debugging purposes at e.g. fieldbus commissioning. See
Chapter 3.4.7.

(4)

(12)

ID: M1
STOP READY I/O
(5)



(13)
(10)
STOP READY I/O
ID: M2.1
0.0rpm
STOP READY I/O
0.00 Hz
ID25
0.00Hz
0.00A 0.00%
20.0 Hz
0.0V
0.0V 81.9°C 0.0%
ID:1 M2.1.1.1
STOP Ready I/O
0.00 Hz
10.00 Hz
0.00 rpm
0.00 A
0.00 %
0.00 %
BT11116
(13)
Main Menu
Quick Setup
Parameters
Monitor
Monitor
Multimonitor
Basic
Timer functions
Multimonitor
FreqReference
Output Freq
Motor Curre Motor Torque Motor Voltage
Motor Speed
Motor TemperaUnit TemperaDC-link volt
FreqReferenc
FreqReference
Output frequency
Motor Power
FreqReference
Motor Speed
Motor Current
Motor Torque

Siemens Industry, Inc. • 14 Keypad of the drive
24-hour support [phone] (Dial 2)
2.2.3 Parameters
Through this sub-menu, you can reach the application parameter groups and parameters. You can find
more information on parameters in Chapter 3.
2.2.4 Diagnostics
Under this menu, you can find Active faults, Reset faults, Fault history, Counters and Software info.
2.2.4.1 Active faults
2.2.4.2 Reset faults
2.2.4.3 Fault history
Menu Function Note
Active faults When a fault/faults display(s), the dis-
play with the name of the fault starts to
blink. Press OK to return to the Diag-
nostics menu. The Active faults sub-
menu shows the number of faults. Se-
lect the fault and push OK to see the
fault-time data.
The fault remains active until it is cleared
with the Reset button (push for 2 s) or
with a reset signal from the I/O terminal or
fieldbus or by choosing Reset faults (see
below).
The memory of active faults can store the
maximum of 10 faults in the order of
appearance.
Menu Function Note
Reset faults In this menu you can reset faults. For
closer instructions, see Chapter 3.7.1.
CAUTION! Remove external Cont-
rol signal before resetting the fault to pre-
vent unintentional restart of the drive.
Menu Function Note
Fault history 40 latest faults are stored in the Fault
history.
Entering the Fault history and clicking OK
on the selected fault shows the fault time
data (details).
Application info Application ID Information (Application ID, Version and
Firmware interface) about applications
loaded
into the variable frequency drive.
Firmware interface
Hardware info Unit power Unit power in kW
Unit voltage Nominal voltage of the unit
Statistics Output current profile
Output frequency profile
Unit temperature profile

Keypad of the drive Siemens Industry, Inc. • 15
24-hour support [phone] (Dial 2) 2
2.2.4.4 Total counters
2.2.4.5 Trip counters
2.2.4.6 Software info
Table 1: Diagnostics menu, Total counters parameters.
Code Parameter Min Max Unit Default ID Description
V4.4.1 Energy counter Varies 2291
Amount of energy taken
from supply network. No
reset.
V4.4.3 Operating time y d hh:mm 2298 Control unit operating time
V4.4.7 Run time y d hh:mm 2293 Motor running time
V4.4.11 Power on time y d hh:mm 2294
Amount of time the power
unit has been powered so
far. No reset.
V4.4.15 Start command
counter 2295
The number of times the
power unit has been
started.
Table 2: Diagnostics menu, Trip counters parameters.
Code Parameter Min Max Unit Default ID Description
P4.5.1 Energy trip counter Varies 2296
Resettable energy
counter.
NOTE: The highest
energy unit shown on the
standard keypad is MW.
Should the counted
energy exceed 999.9 MW,
no unit is shown on the
keypad.
P4.5.3 Operating time y d hh:mm 2299 Resettable. See P4.5.1.
P4.5.4 Operating time y Operating time in total
years
P4.5.5 Operating time d Operating time in total
days
P4.5.6 Operating time hh:mm:ss Operating time in hours,
minutes and seconds
Table 3: Diagnostics menu, Software info parameters.
Code Parameter Min Max Unit Default ID Description
V4.6.1 Software package
V4.6.4 System load 0 100 % 2300 Load on control unit CPU.
V4.6.5 Application name Name of application
V4.6.6 Application ID
V4.6.7 Application version

Siemens Industry, Inc. • 16 Keypad of the drive
24-hour support [phone] (Dial 2)
2.2.5 I/O and hardware
Various options-related settings are located in this menu.
2.2.5.1 Basic I/O
Monitor here the status of inputs and outputs.
Table 4: I/O and Hardware menu, Basic I/O parameters.
Code Parameter Min Max Unit Default ID Description
V5.1.1 Digital input 1 0 1 Status of digital input signal
V5.1.2 Digital input 2 0 1 Status of digital input signal
V5.1.3 Digital input 3 0 1 Status of digital input signal
V5.1.4 Digital input 4 0 1 Status of digital input signal
V5.1.5 Digital input 5 0 1 Status of digital input signal
V5.1.6 Digital input 6 0 1 Status of digital input signal
V5.1.7 Analog input 1
mode 13
Shows the selected (with
jumper) mode for analog input
signal
1 = 0...20 mA
3 = 0...10 V
V5.1.8 Analog input 1 0 100 % Status of analog input signal
V5.1.9 Analog input 2
mode 13
Shows the selected (with
jumper) mode for analog input
signal
1 = 0...20 mA
3 = 0...10 V
V5.1.10 Analog input 2 0 100 % Status of analog input signal
V5.1.11 Analog output 1
mode 13
Shows the selected (with
jumper) mode for analog out-
put signal
1 = 0...20 mA
3 = 0...10 V
V5.1.12 Analog output 1 0 100 % Status of analog output signal

Keypad of the drive Siemens Industry, Inc. • 17
24-hour support [phone] (Dial 2) 2
2.2.5.2 Option board slots
The parameters of this group depend on the option board installed. If no option board is placed in slots
D or E, no parameters are visible. See Chapter 3.5.1 for the location of the slots.
When an option board is removed, info text “F39 Device removed” will display. See Table 3.7.3.
2.2.5.3 Real time clock
2.2.5.4 Power unit settings, Cooling Fan control
The cooling fan operates in optimized or Always-On mode. In the optimized mode, fan speed is
controlled according to the drive‘s internal logic that receives data from temperature measurements (if
supported by the power unit) and the fan stops in 5 minutes when the drive is in Ready state.
In Always-On mode, the fan runs in full speed, without stopping.
Menu Function Note
Slot D Settings Option board related settings.
Monitoring Monitor option board-related info.
Slot E Settings Option board related settings.
Monitoring Monitor option board-related info.
Table 5: I/O and Hardware menu, Real time clock parameters.
Code Parameter Min Max Unit Default ID Description
V5.4.1 Battery state 1 3 2 2205
Status of battery.
1 = Not installed
2 = Installed
3 = Change battery
V5.4.2 Time hh:mm:s
s2201 Current time of day
V5.4.3 Date dd.mm. 2202 Current date
V5.4.4 Year yyyy 2203 Current year
V5.4.5 Daylight saving 1 4 1 2204
Daylight saving rule
1 = Off
2 = EU
3 = US
4 = Russia
Table 6: Power unit settings, Cooling Fan control.
Code Parameter Min Max Unit Default ID Description
V5.5.1.1 Fan control mode 0 1 1 2377 0 = Always On
1 = Optimized
V5.5.1.3 Fan stop 0 1 1
If enabled, the fan will stop
after 5 minutes when the
drive is in Ready state.
0 = Disabled
1 = Enabled

Siemens Industry, Inc. • 18 Keypad of the drive
24-hour support [phone] (Dial 2)
2.2.5.5 Keypad
2.2.5.6 Fieldbus
Parameters related to different fieldbus boards can also be found in the I/O and Hardware menu. These
parameters are explained in more detail in the respective fieldbus manual.
Table 7: I/O and Hardware menu, Keypad parameters.
Code Parameter Min Max Unit Default ID Description
P5.6.1 Timeout time 0 60 mm 0
Time after which the dis-
play returns to page
defined with parameter
P5.6.2.
0 = Not used
P5.6.2 Default page 0 4 0
0 = None
1 = Enter menu index
2 = Main menu
3 = Control page
4 = Multi-monitor
P5.6.3 Menu index
Set menu index for desired
page and activate with
parameter P5.6.2 = 1.
P5.6.4 Contrast 30 70 % 50 Set contrast of the display
(30...70%).
P5.6.5 Backlight time 0 60 min 5
Set the time until the back-
light of the display turns off
(0...60 min). If set to 0 s,
backlight is always on.
Sub-menu level 1 Sub-menu level 2 Sub-menu level 3
RS-485 Common settings Protocol
Modbus RTU Modbus parameters
Modbus monitoring
N2 N2 parameters
N2 monitoring
BACNetMSTP BACNetMSTP parameters
BACNetMSTP monitoring
Ethernet Common settings
Modbus/TCP Modbus/TCP parameters
Modbus/TCP monitoring
BACnetIP BACnetIP parameters
BACnetIP monitoring