Siemens SINAMICS S120 Quick start guide

STARTER Commissioning Manual
___________________
___________________
___________________
___________________
___________________
___________________
SINAMICS
S120
STARTER Commissioning Manual
Commissioning Manual
Applies to:
Firmware Version 4.8
(IH1), 07/2016
6SL3097
-4AF00-0BP5
Preface
Fundamental safety
instructions
1
Preparation for
commissioning
2
Commissioning
3
Diagnostics
4
Appendix
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: 6SL3097-4AF00-0BP5
Ⓟ
06/2016 Subject to change
Copyright © Siemens AG 2004 - 2016.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

STARTER Commissioning Manual
Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5 5
Preface
SINAMICS documentation
The SINAMICS documentation is organized in the following categories:
●General documentation/catalogs
●User documentation
●Manufacturer/service documentation
Additional information
You can find information on the following topics at the following address
(https://support.industry.siemens.com/cs/de/en/view/108993276):
●Ordering documentation/overview of documentation
●Additional links to download documents
●Using documentation online (find and search in manuals/information)
Please send any questions about the technical documentation (e.g. suggestions for
improvement, corrections) to the following e-mail address
(mailto:[e-mail]).
Siemens MySupport/Documentation
At the following address (https://support.industry.siemens.com/My/ww/en/documentation),
you can find information on how to create your own individual documentation based on
Siemens' content, and adapt it for your own machine documentation.
Training
At the following address (http://www.siemens.com/sitrain), you can find information about
SITRAIN (Siemens training on products, systems and solutions for automation and drives).
FAQs
You can find Frequently Asked Questions in the Service&Support pages under Product
Support (https://support.industry.siemens.com/cs/de/en/ps/faq).
SINAMICS
You can find information about SINAMICS at the following address
(http://www.siemens.com/sinamics).

Preface
STARTER Commissioning Manual
6Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5
Usage phases and their documents/tools (as an example)
Table 1 Usage phases and the available documents/tools
Usage phase
Document/tool
Orientation
SINAMICS S Sales Documentation
Planning/configuration •SIZER Engineering Tool
•Configuration Manuals, Motors
Deciding/ordering SINAMICS S120 catalogs
•SIMOTION, SINAMICS S120 and Motors for Production Machines
(Catalog PM 21)
•SINAMICS and Motors for Single-axis Drives (Catalog D 31)
•SINUMERIK & SINAMICS
Equipment for Machine Tools (Catalog NC 61)
•SINUMERIK 840D sl Type 1B
Equipment for Machine Tools (Catalog NC 62)
Installation/assembly •SINAMICS S120 Manual for Control Units and Additional System Components
•SINAMICS S120 Manual for Booksize Power Units
•SINAMICS S120 Manual for Booksize Power Units C/D Type
•SINAMICS S120 Manual for Chassis Power Units, Air-cooled
•SINAMICS S120 Manual for Chassis Power Units, Liquid-cooled
•SINAMICS S120 Manual for AC Drives
•SINAMICS S120 Manual Combi
•SINAMICS S120M Manual Distributed Drive Technology
•SINAMICS HLA System Manual Hydraulic Drive
Commissioning •STARTER Commissioning Tool
•SINAMICS S120 Getting Started with STARTER
•SINAMICS S120 Commissioning Manual with STARTER
•SINAMICS S120 CANopen Commissioning Manual
•SINAMICS S120 Function Manual Drive Functions
•SINAMICS S120 Safety Integrated Function Manual
•SINAMICS S120/S150 List Manual
•SINAMICS HLA System Manual Hydraulic Drive
•Startdrive commissioning tool1)
•SINAMICS S120 Getting Started with Startdrive1)
•SINAMICS S120 Commissioning Manual with Startdrive1)
Usage/operation •SINAMICS S120 Commissioning Manual with STARTER
•SINAMICS S120/S150 List Manual
•SINAMICS HLA System Manual Hydraulic Drive
•SINAMICS S120 Commissioning Manual with Startdrive1)

Preface
STARTER Commissioning Manual
Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5 7
Usage phase
Document/tool
Maintenance/servicing •SINAMICS S120 Commissioning Manual with STARTER
•SINAMICS S120/S150 List Manual
•SINAMICS S120 Commissioning Manual with Startdrive1)
References •SINAMICS S120/S150 List Manual
1) available as of Startdrive V14 release
Target group
This documentation is intended for machine manufacturers, commissioning engineers, and
service personnel who use the SINAMICS drive system.
Benefits
This manual provides all of the information, procedures and operator actions required for the
particular usage phase.
Standard scope
The scope of the functionality described in this document can differ from that of the drive
system that is actually supplied.
●Other functions not described in this documentation might be able to be executed in the
drive system. However, no claim can be made regarding the availability of these functions
when the equipment is first supplied or in the event of service.
●The documentation can also contain descriptions of functions that are not available in a
particular product version of the drive system. The functionality of the supplied drive
system should only be taken from the ordering documentation.
●Extensions or changes made by the machine manufacturer must be documented by the
machine manufacturer.
For reasons of clarity, this documentation does not contain all of the detailed information on
all of the product types, and cannot take into consideration every conceivable type of
installation, operation and service/maintenance.
Technical Support
Country-specific telephone numbers for technical support are provided in the Internet at the
following address (https://support.industry.siemens.com/sc/ww/en/sc/2090) in the "Contact"
area.

Preface
STARTER Commissioning Manual
8Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5
Relevant directives and standards
You can obtain an up-to-date list of currently certified components on request from your local
Siemens office. If you have any questions relating to certifications that have not yet been
completed, please ask your Siemens contact person.
Certificates for download
The certificates can be downloaded from the Internet:
Certificates (https://support.industry.siemens.com/cs/ww/de/ps/13206/cert)
EC Declaration of Conformity
You can find the EC Declaration of Conformity for the relevant directives as well as the
relevant certificates, prototype test certificates, manufacturers declarations and test
certificates for functions relating to functional safety ("Safety Integrated") on the Internet at
the following address (https://support.industry.siemens.com/cs/ww/en/ps/13231/cert).
The following directives and standards are relevant for SINAMICS S devices:
European low-voltage directive
SINAMICS S devices fulfil the requirements stipulated in the Low-Voltage Directive
2014/35/EU, insofar as they are covered by the application area of this directive.
European machinery directive
SINAMICS S devices fulfil the requirements stipulated in the Low-Voltage Directive
2006/42/EU, insofar as they are covered by the application area of this directive.
However, the use of the SINAMICS S devices in a typical machine application has been fully
assessed for compliance with the main regulations in this directive concerning health and
safety.
European EMC Directive
SINAMICS S devices comply with the EMC Directive 2014/30/EU.
EMC requirements for South Korea
SINAMICS S devices with the KC marking on the rating plate satisfy the EMC requirements
for South Korea.
Specification for semiconductor process equipment voltage drop immunity
SINAMICS S devices meet the requirements of standard SEMI F47-0706.
Eurasian conformity
SINAMICS S comply with the requirements of the Russia/Belarus/Kazakhstan customs union
(EAC).

Preface
STARTER Commissioning Manual
Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5 9
North American market
SINAMICS S devices provided with one of the test symbols displayed fulfil the requirements
stipulated for the North American market as a component of drive applications.
You can find the relevant certificates on the Internet pages of the certifiers:
●For products with UL certificate (http://database.ul.com/cgi-
bin/XYV/template/LISEXT/1FRAME/index.html)
●For products with TÜV SÜD certificate (https://www.tuev-
sued.de/industry_and_consumer_products/certificates)
Possible test symbols
Australia and New Zealand (RCM formerly C-Tick)
SINAMICS S devices showing the test symbols fulfil the EMC requirements for Australia and
New Zealand.
Quality systems
Siemens AG employs a quality management system that meets the requirements of ISO
9001 and ISO 14001.
Not relevant standards
China Compulsory Certification
SINAMICS S devices do not fall in the area of validity of the China Compulsory Certification
(CCC).
EMC limit values in South Korea
The EMC limit values to be observed for Korea correspond to the limit values of the EMC
product standard for variable-speed electric drives EN 61800-3 of category C2 or the limit
value class A, Group 1 to KN11. By implementing appropriate additional measures, the limit
values according to category C2 or limit value class A, Group 1, are observed. Further,
additional measures may be required, such as using an additional radio interference
suppression filter (EMC filter).
The measures for EMC-compliant design of the system are described in detail in this manual
respectively in the EMC Installation Guideline Configuration Manual.
The final statement regarding compliance with the standard is given by the respective label
attached to the individual unit.

Preface
STARTER Commissioning Manual
10 Commissioning Manual, (IH1), 07/2016, 6SL3097-4AF00-0BP5
Ensuring reliable operation
The manual describes a desired state which, if maintained, ensures the required level of
operational reliability and compliance with EMC limit values.
Should there be any deviation from the requirements in the manual, appropriate actions (e.g.
measurements) must be taken to check/prove that the required level of operational reliability
and compliance with EMC limit values are ensured.
Spare parts
Spare parts are available on the Internet at the following address
(https://www.automation.siemens.com/sow?sap-language=EN).
Product maintenance
The components are subject to continuous further development within the scope of product
maintenance (improvements to robustness, discontinuations of components, etc).
These further developments are "spare parts-compatible" and do not change the article
number.
In the scope of such spare parts-compatible further developments, connector positions are
sometimes changed slightly. This does not cause any problems with proper use of the
components. Please take this fact into consideration in special installation situations (e.g.
allow sufficient clearance for the cable length).
Use of third-party products
This document contains recommendations relating to third-party products. Siemens accepts
the fundamental suitability of these third-party products.
You can use equivalent products from other manufacturers.
Siemens does not accept any warranty for the properties of third-party products.