Siemens Flowrite 599 Series Owner's manual

Flowrite™ 599 Series
Technical Instructions
Document No. 155-717
September 25, 2018
SKB/C/D 62UA Series
Electronic Valve Actuator 24 Vac
Proportional Control
Advanced Features
SKB/C
SKD
Siemens Industry, Inc.
Description
The Flowrite 599 Series SKB/C/D62UA Electronic Valve Actuator requires a 24 Vac
supply and receives a 0 to 10 Vdc or a 4 to 20 mA control signal to proportionally control
a valve. This actuator is designed to work with valves with a 3/4-inch (20 mm) or 1-1/2-
inch (40 mm) stroke.
Features
•Direct-coupled installation requires no special tools or adjustments
•Visual and electronic stroke indication
•Die-cast aluminum housing
•Manual override
•Spring return to fail-safe position
•Automatic stroke calibration
•Direct or reverse acting
•Adjustable start and span
•Stroke limit control
•Choice of linear or equal-percentage flow characteristic
•Maintenance-free
Application
These electronic actuators are designed to be used with Flowrite 599 Series valves with
either 3/4-inch (20 mm) stroke (SKB/D) or a 1-1/2 inch (40 mm) stroke (SKC) in liquid
and steam service applications; or other manufacturer's valves with appropriate
Universal Valve Linkage Kits.

Technical Instructions Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features
Document Number 155-717
September 25, 2018
Page 2 Siemens Industry, Inc.
Product Numbers
Table 1. Product Numbers.
Actuator
Stroke
Order Number
3/4-inch (20 mm)
SKB62UA
SKD62UA
1-1/2 inch (40 mm)
SKC62UA
Warning/Caution Notations
WARNING:
Personal injury or loss of life may occur if you do not
perform a procedure as specified.
CAUTION:
Equipment damage or loss of data may occur if you
do not perform a procedure as specified.
Specifications
Power Supply
Operating voltage (SELV,PELV) 24 Vac ± 20%
Frequency 50 or 60 Hz
Power consumption
SKB62UA 17 VA/12W
SKC62UA 28 VA/20W
SKD62UA 17 VA/12W
Operating
Type of control (proportional) 0 to 10 Vdc; 4 to 20 mA;
or 0 to 1000 ohms
Running time Opening: Closing:
SKB62UA 120 seconds 15 seconds
SKC62UA 120 seconds 20 seconds
SKD62UA 30 seconds 15 seconds
Spring-return time Closing:
SKB62UA 15 seconds
SKC62UA 20 seconds
SKD62UA 15 seconds
Nominal stroke
SKB62UA 3/4-inch (20 mm)
SKC62UA 1-1/2-inch (40 mm)
SKD62UA 3/4-inch (20 mm)
Position force
SKB/C 62UA 2800N
SKD62UA 1000N

Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features Technical Instructions
Document Number 155-717
September 25, 2018
Siemens Industry, Inc. Page 3
Signal Inputs
Terminal Y
Voltage 0 to 10 Vdc
Input impendence 100K ohm
Current 4 to 20 mA
Input impedance 240 ohm
Signal resolution <1%
Hysteresis <1%
Terminal Z
Resistance 0 to 1000 ohm
Override control functions
Z not connected No function (priority at Terminal Y)
Z connected directly to G Maximum stroke 100%
Z connected directly to G0 Minimum stroke 0%
Z connected to M via 0 to 1000 ohm Linear or equal percentage
Signal Inputs, Continued
Terminal U
Voltage 0 to 9.8 Vdc ± 2%
Load impedance >500 ohm
Current 4 to 19.6 mA ± 2%
Load impedance <500 ohms
Ambient Conditions
Media temperature
SKD 20°F to 300°F (-7°C to 150°C)
SKB/C 20°F to 337°F (-7°C to 170°C)
Operation To IEC 721-3-3
Environmental conditions Class 3K5
Temperature
SKD 5°F to 122°F (-15°C to 50°C)
SKB/C 5°F to 130°F (-15°C to 55°C)
Humidity 5% to 95% rh
Transport To IEC 721-2-1
Environmental conditions Class 3K5
Temperature 22°F to 149°F (-5°C to 65°C)
Humidity <95% rh
Storage To IEC 721-3-1
Environmental conditions Class 1K3
Temperature
SKD 5°F to 122°F (-15°C to 50°C)
SKB/C 5°F to 130°F (-15°C to 55°C)
Humidity 5% to 95% rh
Agency Certification
UL Listed to UL873
C-UL Certified to Canadian standard
C22.2 No. 24-93
Meets CE requirements:
EMC Directive 89/336/EEC
C-tick N474
Protection standard IP54 to EN 60 529
Protection Class III to EN 60 730

Technical Instructions Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features
Document Number 155-717
September 25, 2018
Page 4 Siemens Industry, Inc.
Miscellaneous
Materials
Actuator housing and bracket Die-cast aluminum
Housing box and manual adjustor Plastic
Conduit opening 1/2-inch NPSM
Dimensions See Figure 23, Figure 24, Figure 25
and Figure 26.
Weight
SKB62UA 18.9 lbs (8,60 kg)
SKC62UA 22.5 lbs (10,00 kg)
SKD62UA 8.5 lbs (3,85 kg)
Housing
NEMA Rating NEMA 1 (Interior only)
See Accessories
Advanced Features
Direction of Operation
Direct acting / reverse acting 0 to 10 Vdc; 10 to 0 Vdc
4 20 mA; 20 to 4 mA
0 to 1000 ohm/1000 to 0 ohm
Stroke Limit Control
Range of lower limit 0% to 45% adjustable
Range of upper limit 100% to 55% adjustable
Sequence Control
Starting Point of Sequence (Start) 0 to 15V adjustable
Operating Range of Sequence (Span) 3 to 15V adjustable
Accessories
Figure 1. Auxiliary Switch.
ASC1.6 Auxiliary switch
•Sends a signal to indicate that the valve is
in the 0% stroke position.
•The switching point is fixed at the 0%
stroke position.
Switching capacity 24 Vac
4A resistive,
2A inductive
Lowest recommended current 10 mA
Figure 2. Stem Heating Element.
ASZ6.6 The stem heating element prevents
the formation of ice on the stem when the
medium temperature drops below 32°F (0°C).
It is suited for universal use with valves having
a stem or spindle diameter of 10 or 14 mm.
Operating voltage 24 Vac/dc ± 20%
Power consumption ≤40 VA/30W
Figure 3. SKB/C Weather Shield.
599-10065 The SKB/C actuator is UL listed to
meet NEMA Type 3R requirements (a degree
of protection against rain, sleet, and damage
from external ice formation) when installed with
this weather shield and outdoor-rated conduit
fittings in the vertical position. See Service Kits
for replacement ultraviolet resistant cable ties.

Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features Technical Instructions
Document Number 155-717
September 25, 2018
Siemens Industry, Inc. Page 5
Accessories,
Continued
Figure 4. SKD Weather Shield.
599-10071 The SKD actuator is UL listed to
meet NEMA TYPE 3R requirements (a degree
of protection against rain, sleet, and damage
from external ice formation) when installed with
this weather shield and outdoor-rated conduit
fittings in the vertical position. See Service Kits
for replacement ultraviolet resistant cable ties.
Figure 5. Valve Retrofit Kit.
Universal Retrofit Kit
Kit contains the parts needed to adapt a valve
to the following Siemens 599 Series Flowrite
actuators: SKB, SKC, SKD, SQX. Selected
valves from the following manufacturers can
also be accommodated: Honeywell, Johnson
Controls, and Siebe. See your local Siemens
representative for details.
Service Kits
Circuit board replacement 4 668 5751 8
Manual override kit 4268 5510 8
Plastic wiring compartment cover 4 104 5582 8
Stem retainer kit
Contains one stem nut (Figure 7, Item 6) and one stem retainer clip.
2-1/2 and 3-inch valves 599-10048
4, 5, and 6-inch valves 599-10049
Retainer clamp kit 599-10200
Ultraviolet (UV) resistant cable ties (pkg. of 8) 538-994
WARNING:
This product contains a spring under high compression. Do not
attempt to disassemble the actuator.
Valve Details
Figure 6. SKB/C Valve Parts.
1. Manual Adjuster
2. Pressure Cylinder
3. Piston
4. Reservoir
5. Pressure Chamber
6. Pump
7. Return Spring
8. Bypass Valve
9. Coupling
10. Valve Stem
11. Inner Valve
12. Position Indicator (0 to 1)

Technical Instructions Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features
Document Number 155-717
September 25, 2018
Page 6 Siemens Industry, Inc.
Valve Details,
Continued
Figure 7. SKD Valve Parts.
1. Pressure cylinder
2. Piston
3. Oscillating pump
4. Return spring
5. Bypass valve
6. Valve stem retainer
7. Manual override knob
8. Position indicator
Standard Operation
Figure 8. SKB/C Valve Stem Travel Indication.
Figure 9. SKD Valve Stem Travel Indication.
The actuator accepts a 0 to 10 Vdc or a 4 to 20 mA control signal. The actuator
mounted on a valve produces a stroke proportional to the input signal. When power is
turned off or in the event of a power failure, the actuator spring returns the valve to its
normal position.
Direct Acting

Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features Technical Instructions
Document Number 155-717
September 25, 2018
Siemens Industry, Inc. Page 7
Mounting and
Installation
The vertical position is the recommended position for mounting and the only position for
NEMA Type 3R rating with the Weather Shield. Acceptable mounting positions are shown
in Figure 10.
Figure 10. Acceptable Mounting Positions.
Allow four inches (100 mm) around the sides and back of the actuator and eight inches
(200 mm) above and to the front of the actuator.
See dimensions in Figure 23, Figure 24, Figure 25, and Figure 26.
Detailed installation instructions for field mounting are shipped with the actuator.
CAUTION:
When removing the knockout do not damage the circuit board. Use
the top knockout position, if possible.
Start-up
Check the wiring for proper connections.
NOTE: The valve body assembly determines the complete assembly action.
Spring Return
Function
All SKB/C/D62UA actuators are factory-fitted with a spring-return function. If the control
signal or power supply fails, the actuator will return to the 0% stroke position (stem fully
retracted).
Override Control
The override control input (Z) has three modes of operation:
NOTE: The Z-modes have a "direct acting" factory setting.

Technical Instructions Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features
Document Number 155-717
September 25, 2018
Page 8 Siemens Industry, Inc.
Stroke Calibration
To determine the stroke positions 0% and 100% in the valve, calibration is required when the
valve/actuator are commissioned for the first time. The actuator must be mechanically
connected to a valve and must have a supply voltage of 24 Vac. The calibration procedure can
be repeated as often as necessary
CAUTION:
Before starting calibration, be sure that the manual adjuster is set to Automatic for
the actual values to register.
There is a slot on the printed circuit boards for the actuators. To
initiate the calibration procedure, the contacts inside this slot must
be short-circuited (possibly with a screwdriver). See Figure 11.
Automatic calibration proceeds as follows (see Figure 12):
•Actuator runs to the 0% stroke position (1), the green LED
flashes.
•Actuator then runs to the 100% stroke position (2), the
green LED flashes.
•Measured values are stored in the EPROM.
•The actuator now moves to the position defined by control
signal Y or Z (3), and the green LED now glows steady
(normal operation).
•Throughout this procedure, output Uis inactive, meaning
the values only represent actual positions when the green
LED stops flashing and remains on continuously.
Figure 11.
Figure 12.
Automatic Calibration.
Table 2. LED Status.
LED
Display
Function
Action
Green
ON
Normal Operation
Automatic operation
Flashing
Stroke calibration In
Progress
Wait for calibration to be
completed (LED stops flashing)
Red
ON
Faulty stroke calibration
Internal Error
- Check mounting
- Restart stroke calibration (by
short-circuiting calibration slot)
- Replace electronics
Flashing
Valve plug jammed
Check the valve
OFF
•No power supply
•Faulty electronics
- Check mains
- Replace electronics

Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features Technical Instructions
Document Number 155-717
September 25, 2018
Siemens Industry, Inc. Page 9
Start-up, Continued
Advanced Features
1
2
3
4
Figure 13. DIP Switches.
DIP Switches
(From Left to Right)
1
Select
Direction of
Operation
2
Sequence Control
or
Stroke Limit Control
3
Selection of
Control
Signal
4
Selection of
Flow
Characteristic
ON
Reverse-acting
Sequence control
4 to 20 mA
Modified*
OFF
(Factory Settings)
Direct-acting
Stroke limit control
0 to 10 Vdc
Default
*Changing the default setting will modify an equal percentage valve to a linear flow characteristic. When
set to default, the flow characteristic is determined by the valve body.

Technical Instructions Flowrite 599 Series SKB/C/D 62UA Electronic Valve Actuator Advanced Features
Document Number 155-717
September 25, 2018
Page 10 Siemens Industry, Inc.
Start-Up,
continued
Selecting the
Direction of
Operation
•With normally-closed valves, "direct-acting" means that with a 0 Vdc signal input, the valve
is closed.
•With Normally-open valves, "direct-acting" means that with a 0 Vdc signal input, the valve
is open.
Input:
0 to 10 Vdc
Input
10 to 0 Vdc
0 Vdc
10 Vdc
4 to 20 mA
20 to 4 mA
4 mA
20 mA
0 to 1000 ohm
1000 to 0 ohm
0 ohm
1000 ohm
Figure 14. Direction of Operation.
Sequence Control
or Stroke Limit
Control
Check the wiring for proper connections.
NOTE: The valve body assembly determines the complete assembly action.
Table 3. Table 4.
Setting the Stroke Limit Control
Setting the Sequence Control
The rotary switches LO and UP can be
used to apply an upper and lower limit
to the stroke in increments of 3% up to
a maximum of 45%.
The rotary switches LO and UP can be used
to determine the starting point (Start) or the
operating range of a sequence (Span).
Position
of
LO
Lower
Stroke
Limit
Position
of
UP
Upper
Stroke
Limit
Position
of
LO
Starting
Point for
Sequence
Control
Position
of
UP
Operating
Range of
Sequence
Control
0
0%
0
100%
0
0V
0
10V
1
3%
1
97%
1
1V
1
10V*
2
6%
2
94%
2
2V
2
10V*
3
9%
3
91%
3
3V
3
3V*
4
12%
4
88%
4
4V
4
4V
5
15%
5
85%
5
5V
5
5V
6
18%
6
82%
6
6V
6
6V
7
21%
7
79%
7
7V
7
7V
8
24%
8
76%
8
8V
8
8V
9
27%
9
73%
9
9V
9
9V
A
30%
A
70%
A
10V
A
10V
B
33%
B
67%
B
11V
B
11V
C
36%
C
64%
C
12V
C
12V
D
39%
D
61%
D
13V
D
13V
E
42%
E
58%
E
14V
E
14V
F
45%
F
55%
F
15V
F
15V
*The smallest adjustment is 3 Vdc; Control with 0 to
3 Vdc is possible only via Y.