Siemens SSA911.02ZB User manual

Connected Home Radiator Valve Actuator ZigBee, wireless
SSA911.02ZB
Wireless radiator valve actuator, works with SIEMENS Connected Home
●RF-controlled actuator communication based on ZigBee protocol (2.4 GHz,
bidirectional)
●Connects and operates with Connected Home hub and receiver
●Battery-operated with commercially available 1.5 V AA batteries
●Valve thread connection M30x1.5 mm
●Nominal stroke 5 mm
●Valve positioning force 90 N
●Adapts automatically to valve
●Integrated temperature sensor and PI controller
●Set temperature on device or via app
A6V13722083_de--_a
Smart Infrastructure
2022-12-12

2
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Application
●The SSA911.02ZB wireless radiator valve actuator is designed to work on radiator
valves from different manufacturers in HVAC applications using M30x1.5 thread. It
operates the valve to control water flow and room temperature.
●The valve actuator works in combination with Connected Home Hub GTW100ZB and
wireless repeater RCR110.2ZB (as an option)
●One Connected Home Hub GTW100ZB can pair with up to 32 radiator valve actuators in
parallel. Wireless repeaters RCR110.2ZB extend the range of the network.
Siemens Connected Home
(App)
GTW100ZB
SSA911.02ZB
RCR110.2ZB
Basic functions
Functions
Description
Communication
The communication protocol is ZigBee.
ZigBee is a low-power wireless mesh networking protocol and enables device-to-device and
device-to-cloud communications. ZigBee is based on IEEE 802.15.4 radio standard.
Parallel operation
A single Connected Home Hub GTW100ZB can pair up to 32 actuators.
Pairing
The Connected Home app pairs the devices.
Calibration
The actuator automatically detects the end positions of the radiator valve.
Temperature
setting
Push buttons on the device set the setpoint temperature
Type summary
Type
Article number
Description
SSA911.02ZB
S55181-A105
Radiator valve actuator

3
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Scope of delivery
●Radiator valve actuator SSA911.02ZB
●2 AA alkaline batteries (LR6)
●Quick guide (A5W00205935A)
●Third-party valve adapter for Danfoss (RA, RAV, RAVL)
●Screw and nut for adapter
Equipment combinations
Siemens valves
The SSA911.02ZB is suited for the following Siemens radiator valve types:
Type
kVS
[m3/h]
V

[l/h]
PN
Data sheet
VDN1.., VEN1..
Radiator valves
0.63…1.41
-
10
N2105
VDN2.., VEN2.., VUN2..
N2106
VD1..CLC..
1.9…2.6
N2103
VD1.., VE1.. *
Radiator valves
0.25…3.4
-
N2145
VD2.., VE2.., VU2.. *
N2146
VPD/VPE/VPU..
Radiator PICV
-
20…135
10
A6V13599366
kVS
=
Flow nominal value for cold water (5. 30 °C) through a fully opened valve (H100), at differential pressure
of 100kPa (1 bar)
V

=
Volume flow
*
No longer available
Third-party valves without adapter
The SSA911.02ZB can operate third-party radiator valves without adapter, provided they
have a M30x1.5 mm connecting thread and meet the following requirements:
Force
90 N nominal
Fully closed
x > 9,0 mm
Fully open
y ≤ 14,5 mm
Valve pre-adjustment / kV-limitation
For valve pre-adjustments, refer to the relevant technical documentation on the valves.
Ensure a minimum valve stroke of > 0.5 mm.

4
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Accessories
Adapters for SSA911.02ZB for use with third-party valves
Type
Article number
For use with...
Adapter thread
AV52
BPZ:AV52
Comap
M28x1,5
AV56
BPZ:AV56
Giacomini
-
AV57
BPZ:AV57
Herz
M28x1,5
AV58
BPZ:AV58
Oventrop < 2002
M30x1
AV59
BPZ:AV59
Vaillant
-
AV60
BPZ:AV60
TA < 2002
M28x1,5
AV61
BPZ:AV561
MMA Markaryd
M28x1.5
Contact your local office or branch for information on adapters for other radiator valve types
and manufacturers.

5
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Third-party valve adapter
Adapters for Danfoss RA/RAV/RAVL valves included in delivery.
•Remove connects on the
plastic adapter before using
one of the included adapters.
•Use supplied screw and nut.
•Insert pin on valve stem.

6
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Product documentation
Title
Contents
Document ID
Connected Home Radiator Actuator
ZigBee SSA911.02ZB
Data sheet: Product description
A6V13722083
Quick guide Connected Home
Radiator Actuator ZigBee
SSA911.02ZB
Quick guide for mounting, commissioning, and
operation SSA911.02ZB
A5W00293080A
Connected Home Hub GTW100ZB
Data sheet: Product description
A6V12640776
Quick guide Connected Home Hub
GTW100ZB
Quick guide for mounting, commissioning, and
operation SSA911.02ZB
A6V12694180
Connected Home Receiver
RCR110.2ZB
Data sheet: Product description
A6V12680327
Quick guide Connected Home
Receiver RCR110.2ZB
Quick guide for mounting, commissioning, and
operation RCR110.2ZB
A6V11562443
Related documents such as environmental declarations, CE declarations, etc., can also be
downloaded at:
www.siemens.com/bt/download
Notes
Safety
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
WARNUNG
Burns from hot surface
The screw nut that fastens the actuator to the radiator valve can become hot. Risk of burns
from touching the screw nut.
When servicing the actuator:
●Switch off the radiator and allow it to cool down.

7
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
WARNUNG
Explosion due to fire or short circuit, even with empty batteries
Risk of injury due to flying parts
●Do not expose batteries to water.
●Do not recharge batteries.
●Do not damage or disassemble batteries.
●Do not expose batteries to temperatures over 85 °C.
WARNUNG
Leakage of electrolyte
Severe burns
●Wear protective gloves to handle damaged batteries.
●In case of contact with electrolyte, rinse eyes immediately with plenty of water. Consult
a doctor.
Observe the following:
●Correct polarity (+/-).
●Use new batteries and inspect for damage.
●Do not mix old and new batteries.
Store, transport and dispose of the batteries in compliance with local requirements,
regulations, and laws. Also observe the instructions of the battery manufacturer.
Switching off the device or loss of communication to the radiator valve actuator may result
in an “undefined state” and quickly drain the batteries.
Do not switch off Connected Home Hub and use a repeater as need to ensure proper
communications.
Mounting SSA911.02ZB is mounted on the radiator valve. There are no preferred mounting positions;
actuator SSA911.02ZB can be operated in all mounting positions. The display must be
clearly visible and the buttons easy to access.
WARNUNG
Falling objects
Overhead installation may result in injury from falling objects.
●Do not install the actuator more than 2 m above ground
●Firmly hand tighten the screw nut clockwise to attach the actuator to the valve or
adapter.

8
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Removal
●Delete the device from the Siemens Connected Home App.
●Press the Reset button in the battery compartment for ca. 10 seconds.
●The LCD displays “PA” and counts up to 10.
●Release the Reset button after 10 seconds.
➔The LCD display turns off and the valve stem goes to the mounting position.
●Turn the screw nut counterclockwise and remove from the radiator valve actuator.
Commissioning
●Install the Connect Home mobile app.
–The app provides step-by-step commissioning instructions.
●Install and commission the Connected Home Hub GTW100ZB (see quick guide
A6V12694180).
●Optional: Install and commission the Connected Home Receiver Hub CR110.02ZB (see
quick guide A6V11562443).
●Install and commission the Connected Home Radiator valve actuator SSA911.02ZB (see
quick guide A5W00293080A).

9
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
Operation
HMI
The interface consists of an LCD display and two touch
elements.
Lower temperature
Increase temperature
Buttons
Press once
Lower room temperature by 0.5 ℃.
Press and hold
Immediately lowers room temperature by 0.5 ℃,
followed by another 0.5 ℃every 0.5 s the button
is held or until the lowest temperature is reached.
If the settings is less than 8 °C, the LCD displays
“—” and control is switched off.
Press once
Increases room temperature by 0.5 ℃.
Press and hold
Immediately increases room temperature by 0.5
℃, followed by another 0.5 ℃every 0.5 s the
button is held or until the highest temperature is
reached.
When a temperature higher than 28 °C is set,
"ON" appears on the LCD display. The boost
mode is activated for 5 min.
and
Press and hold together for 3 s
Lock or unlock buttons.
If “Ad”, press together and hold for
3 s
Starts adaptation
Reset button
Battery compartment
Press Reset button in battery
compartment and hold for 10 s
Delete the device list from the Connected Home
app to reset to factory settings.
Reset can be performed after 10 s (LCD indicates
how long to press as of 5 s).
Press and hold for 5 s
The device is deleted from the network.
Press and hold for 3 s
Displays the discovered network (Zigbee Node
ID).

10
Siemens
A6V13722083_de--_a
Smart Infrastructure
2022-12-12
LCD indication
Informs about wireless connection and pairing.
On: Connected to gateway.
Off: Not connected to gateway.
Pairing (inclusion) is active.
●Do not operate the actuators in pairing mode over longer periods; this
quickly drains the batteries.
Perform a factory reset if pairing fails after multiple attempts and then try
again per the documentation.
Remove mode (exclusion) active.
Start adaptation.
On during adaptation.
On if button lock is enabled/disabled.
On if battery capacity drops below 15%.
Change operating mode
Operating mode
OFF mode
Press touch element and hold until the LCD displays “--” and the radiator valve
actuator switches off.
Heating mode
The two touch elements and set the temperature between 8 and 28°C.
If the device is not in heating mode, use the touch elements to change the temperature
between 8 and 28 degrees.
Boost mode
To change the device to boost mode, press and hold touch element until the LCD
displays "ON".
Boost mode switches off automatically after 5 minutes.
Window open
mode
“Window open” activates if the temperature suddenly drops. SSA911.02ZB switches to
OFF mode for 15 minutes.
The Window open function switches off after 15 minutes and the device returns to the
last active mode.
Error codes
Error codes
An error code displays on the SSA911.02ZB in the event of a malfunction or communication
error with Connected Home Hub.
Press the plus or minus button to clear error codes.