Siemens Synco 200 User manual

Answers for infrastructure.
Synco 200 –
Commissioning guide

2
This guide provides basic instructions for configuring and starting the Synco™ 200
controllers.
It contains tables showing all symbols and basic texts that are used with
Synco 200. Additionally, all preprogrammed applications are shown as small plant
diagrams, to help you to find the required controller and the corresponding number of
preprogrammed application.
Summarized, this booklet provides you with all necessary basic information to commis-
sion the Synco 200 controllers in an easy, comfortable and efficient way.
If you need more detailed information, please refer to the Synco 200 basic documenta-
tion (Document No. CE1P3101en) or contact your local Siemens office.
Synco 200 – Commissioning guide

3
Content
Introduction ...................................................4
Operating elements and symbols ...................................4
List of abbreviations .............................................4
Commissioning ................................................7
Access levels overview ...........................................7
Navigation overview – user level ...................................8
Navigation overview – service level ................................10
Navigation overview – password level ..............................12
Getting started ................................................14
1) How to get into the password protected area.....................14
2) How to select a standard application (APPL ID) ...................14
3) How to start a standard application ............................15
4) How to adjust configuration and settings .......................16
5) How to check inputs and outputs (INFO) ........................17
6) How to define setpoints (SET) ................................18
7) How to protect your settings by selecting the user level ............19
Info pages overview ...........................................20
Preprogrammed applications ....................................21
Air handling applications ........................................21
Air pressure, air quality and air flow control........................21
Temperature control: Cooling coil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Temperature control: Heating coil, water ..........................23
Temperature control: Heating coil, electric.........................24
Temperature control: Heating + cooling coil, water (1) ...............25
Temperature control: Heating + cooling coil, water (2) ...............26
Temperature control: Heating + cooling coil, DX cooler ...............27
Temperature control: Heating + cooling coil, electric heater ...........28
Temperature control: Heating + cooling coil + mixing dampers .........29
Temperature control: Heating + cooling coil + heat recovery...........30
Temperature control: Heating coil + mixing dampers/heat recovery .....31
Humidity control: Dehumidifier .................................32
Humidity control: Humidifier ...................................33
Temperature and humidity control: Heating + cooling coil +
mixing dampers/heat recovery + humidifier........................34
Applications for Asian and American regions .......................35
Heating/Cooling applications .....................................36
Temperature and differential temperature control ...................36
Differential pressure control, liquid ..............................37
Special applications.............................................38
Configuration Diagrams ........................................40
IntroductionCommissioningApplicationsConfiguration

4
Introduction
Operating elements and symbols
Operating elements
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5 D1
D2
1
X1
X2
2
X3 X4
MODE
3P
1 Display
2 Navigation buttons – for selec-
t
ing menu lines or adjusting values
3 OK button – for confirming menu
lines or values
4 ESC button – for returning to the
previous menu or for rejecting the
value entered
Symbols and characters on the display
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Info pages
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Outside temperature
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Service level
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Room temperature
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Password level
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Supply air temperature
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Adjustable setpoint
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Protection
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Navigation arrows
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Room operating mode „Comfort“
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Fault
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Room operating mode „Economy“
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Frost protection
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Controller 1 (or 2)
Symbols and characters on the service and password level
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Commissioning
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Info about inputs/outputs
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Parameter settings
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Lock access
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Basic configuration
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Adjustable value
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Extra configuration
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Operating mode
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Wiring test
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Frost protection
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Pump
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Step switch
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Analog output
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
3-position output
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Mixing damper/Heat recovery
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Lineary step switch
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Binary step switch
Note: the enduser level is active when the display shows neither the service level nor the password level symbol.

5
Introduction
List of abbreviations
°C Degrees Celsius
°F Degrees Fahrenheit
%OPEN Outside temp-dependent open
0.0 Universal 000.0
0000 Universal 0000
0–10 0–10 V
2xNI 2 Ni1000 sensors
3P 3-position
3-POINT 3-position output
ABasic type A room temp controller
ACCESS Access levels
ACK Fault acknowledgement
ACTING Control loop with risk of frost
ACTTIME Actuator running time
ADAP Plant type adapted
ALM OFF Fan release relay
AO Modulating output
APPL ID Basic configuration
CAS/CON Casc/const changeover input
CASC Cascade
CAUTION NEW Caution! New configuration
CH OVER 2-pipe heating/cooling system
CLOS Closing
CLSD Closed
CMF Comfort
CMP1D [Setp compensation 1] delta
CMP1END [Setp compensation 1] end
CMP1STT [Setp compensation 1] start
CMP2D [Setp compensation 2] delta
CMP2END [Setp compensation 2] end
CMP2STT [Setp compensation 2] start
CNST Constant
CO SEQ1 Change to sequence 1
CO SEQ2 Change to sequence 2
CO SEQ4 Change to sequence 4
CO SEQ5 Change to sequence 5
COMMIS Commissioning
CONFIG Extra configuration
COOL Cooling
COOLER Cooling coil valve
CORR Correction
CTL1 Controller 1
CTL2 Controller 2
CTLOOP 1 Controller 1
CTLOOP 2 Controller 2
DIFF Differential input
DIG Frost protection unit
DIG Digital
DLY OFF Switch-off delay
DMP Mixed air damper
DV ALM Deviation message
DV DLYH Deviation message delay high
DV DLYL Deviation message delay low
ECO Economy
ERC Heat recovery equipment
FROST Frost protection
FRST Frost protection
HEAT Heating
HREC Mixing damper/Heat recovery
INFO Information inputs/outputs
IN X Preselection external
INVALID Caution! Invalid settings
INVERS Inversion
KICK Kick period
LABEL Input identifier
LIM General limit controller
LIM DHI General limiter differential high
LIM DLO General limiter differential low
LIM MAX General limiter limit value high
LIM MIN General limiter limit value low
LIM TN General limiter integral action time Tn
LIM XP General limiter P-band Xp
LOCK S1 [Sequence 1] outside temp-dependent locked
LOCK S2 [Sequence 2] outside temp-dependent locked
LOCK S4 [Sequence 4] outside temp-dependent locked
LOCK S5 [Sequence 5] outside temp-dependent locked
MAIN Main controlled variable
MAINALM Main controlled variable sensor error
MAT Mixed air temperature
MAT XP Mixed air temp P-band Xp
MAT TN Mixed air temp integral action time Tn
MAX Limitation max
MAX Maximum
MAX POS Positioning signal max
MAX VAL Value high
MECH 1 MECH input 1
MECH 2 MECH input 2
MECHSET MECH limit value
MIN Limitation min
MIN Minimum
MIN POS Positioning signal min
MIN VAL Value low
MODE Operating mode
NI Passive Ni1000 Sensor
NO No
NO None
NORMPOS Normal position
OFF Off
OFF TN Plant OFF Tn
OFF XP P-band Xp
OFFTIME Locking time
OFF-Y Load-dependent OFF
OHM
OK
ON On
ON DLY Startup delay
ON-OUTS Outside temp-dependent ON
ON-Y Load-dependent ON
OPEN Opening
OPEN Open
OPMODE Preselected operating mode input
ORIG Plant type original (not adapted)
OUTS Outside temperature
OUTSIDE Actual value outside temperature

6
PASS Password level
PASSWRD Enter password
PASSWRD Password
PRIO CH Run priority changeover
PRT Protection
PT Platin sensor
PUMP 1 Pump 1
PUMP 2 Pump 2
PUMP 3 Pump 3
REM1 [Controller 1] remote setpoint adjuster
REM2 [Controller 2] remote setpoint adjuster
ROOM Room temperature
ROOM Actual value room temperature
ROOM TN Room influence Tn
ROOM XP Room influence Xp
S V1 Variable step switch 1
S V2 Variable step switch 2
S1-OFF [Step 1] OFF
S1-ON [Step 1] ON
S2-OFF [Step 2] OFF
S2-ON [Step 2] ON
S3-OFF [Step 3] OFF
S3-ON [Step 3] ON
S4-OFF [Step 4] OFF
S4-ON [Step 4] ON
S5-OFF [Step 5] OFF
S5-ON [Step 5] ON
S6-OFF [Step 6] OFF
S6-ON [Step 6] ON
SAT Supply air temperature
SBIN Binary step switch
SEQ Sequence limiter controller
SEQ MOD Type of limitation
SEQ SEL Sequence selection
SEQ SET Sequence limiter limit value
SEQ XP Sequence limiter P-band Xp
SEQ TN Integral action time Tn
SEQ1 Sequence 1
SEQ1 P [Sequence 1] pump
SEQ1 TN [Sequence 1\_ ] Tn
SEQ1 TV [Sequence 1\_ ] Tv
SEQ1 XP [Sequence 1\_ ] Xp
SEQ1 Y [Sequence 1] load
SEQ2 Sequence 2
SEQ2 P [Sequence 2] pump
SEQ2 TN [Sequence 2\ .._ ] Tn
SEQ2 TV [Sequence 2\ .._ ] Tv
SEQ2 XP [Sequence 2\ .._ ] Xp
SEQ2 Y [Sequence 2] load
SEQ4 Sequence 4
SEQ4 P [Sequence 4] pump
SEQ4 TN [Sequence 4 _/ ] Tn
SEQ4 TV [Sequence 4 _/ ] Tv
SEQ4 XP [Sequence 4 _/ ] Xp
SEQ4 Y [Sequence 4] load
SEQ5 Sequence 5
SEQ5 P [Sequence 5] pump
SEQ5 TN [Sequence 5 _.. / ] Tn
SEQ5 TV [Sequence 5 _.. / ] Tv
SEQ5 XP [Sequence 5 _.. / ] Xp
SEQ5 Y [Sequence 5] load
SERV Service level
SET MAX
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Comfort setpoint high
SET MAX
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Economy setpoint high
SET MIN
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Comfort setpoint low
SET MIN
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Economy setpoint low
SETCLIM Cooling setpoint limitation
SETCOOL
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Comfort cooling setpoint
SETCOOL
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Economy cooling setpoint
SETHEAT
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Comfort heating setpoint
SETHEAT
LIN BIN 123
°F
°C
K
%
COMMIS
PARA
APPL ID
INFO
SET
SERVICE PASS
PARA
SET
CONF
TEST
X5D1
D2
1
X1
X2
2
X3 X4
MODE
3P
Economy heating setpoint
SETHLIM Heating setpoint limitation
SET-OFF Plant OFF frost protection setpoint
SET-ON Risk of frost limit
SETPOINT Setpoints
SETTING Settings
SHIFT Universal shift
SIGNALY Measured value signal output
SLIN Linear step switch
START OK Caution! Plant starts
STATUS Device state
STEP 1 Step 1
STEP 2 Step 2
STEP 3 Step 3
STEP 4 Step 4
STEP 5 Step 5
STEP 6 Step 6
STEP V1 Variable step switch 1
STEP V2 Variable step switch 2
STEPBIN Binary step switch
STEPLIN Linear step switch
STOP OK Caution! Plant stops
STRATGY Control strategy
STUP-TI Startup time
SU DMAX Maximum limitation supply air delta
SU DMIN Minimum limitation supply air delta
SU MAX Supply air limit value max
SU MIN Supply air limit value min
SUM-D Summer compensation delta
SUM-END Summer compensation end
SUM-STT Summer compensation start
SW-VERS Software version
TIMEOUT Control timeout
TOOLING Operation locked
TYPE Type
TYPE Identification
UBasic type U universal controller
UNIT Unit
USER User level
VALUES Inputs/outputs
WIN-D Winter compensation delta
WIN-END Winter compensation end
WIN-STT Winter compensation start
WIRING TEST Wiring test
XP P-band Xp
YES Yes
YES Acknowledgement manual
YES3 Acknowledgement automatic 3x

7
Commissioning
Commissioning
Access level overview
How to get into the different access levels
User level Service level Password level
Access to info pages and Access to info pages Access to all menus
setpoint menu and setting menus
Press OK + ESC Press OK + ESC Press OK + ESC
Menu overview Menu overview Press OK
(see page 8) (see page 10)
Menu overview
(see page 12)
Select 2
Press OK

8
8
Navigation overview – user level
Setpoint menu
Info pages
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)
SET to define setpoints
(see page 18)

9
Commissioning
9
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)

10
Navigation overview – service level
Setting menus
Info pages
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)
PARA to define parameters
(see page 16)
INFO shows all inputs and
outputs (see page 17)

11
Commissioning
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)
SET to define setpoints
(see page 18)

12
Navigation overview – password level
PARA to define parameters SET to define setpoints
Setting menus
Commissioning
menus
(see page 16)
Info pages
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)
INFO shows all inputs and
outputs (see page 17)

13
Commissioning
Info pages show actual values, setpoints, fault messages and other user relevant data (see page 20)
APPL ID to choose an
application
CONF to define configu-
ration
TEST to check inputs and
to simulate outputs
SET to define setpoints
(see page 18)
PARA to define parameters
(see page 16)

14
Getting started
1 How to get into the pass-
word protected area
Press OK + ESC
Press OK
Press OK
2 How to select a preprogrammed application
(APPL ID)
Info page in the
password level
Setting menus
Press OK
Press OK
Stop the plant
Commissioning
menus
Press OK
Select APPL ID
Press OK
Application menu

15
Commissioning
3 How to start a preprogrammed application
Application number
Warning page
Press OK, select number, press OK
Press OK
Parameter menu
(to define parame-
ters see page 16)
Start the plant
Press ESC
Press OK
Press ESC
Commissioning
menu
Info page

16
4 How to adjust configuration and settings
– How to define parameters (PARA), setpoints (SET), applications (APPL ID)
– How to adjust a standard application (CONF)
– How to test inputs and outputs (TEST)
Menus in COMMIS
Parameter menu:
Select PARA
Setpoint menu:
Select SET
(see page 18)
Press OK
Application menu:
Select APPL ID
(see page 14)
Configuration
menu:
Select CONF
Wiring test menu:
Select TEST
…to define parameters Select an input or a function
…to define setpoints Define the heating setpoint
Press OK
Press OK
…to select an application Select a number
Press OK
Press OK
…to adjust or define an
application
Select an input or a function
…to test inputs and outputs Select an input or a function

17
Commissioning
5 How to check inputs and outputs (INFO)
(only in password or service level)
This menu allows you to look up all input and output values to check your plant.
Info page
INFO menu
Press OK
Select INFO
Press OK
Checking outside
temperature
Press ESC
Press ESC

18
6 How to define setpoints (SET)
(in all levels)
Info page
Commissioning
menu
Press OK
Select SET
Press OK
Setpoint menu
Press ESC
Setpoints
Press OK
Press ESC

19
Commissioning
7 How to protect your settings by selecting the user level
Info page in the password level
Change to the user level
Press OK + ESC
Select USER
Press OK
Info page in the user level

20
Info pages overview
Number and content of the info pages depend on the loaded application
User level Service and Description
password level
Shows actual room temperature
and setpoint
Shows actual supply air tempe-
rature and calculated setpoint
or temperature limits
Shows all configured sequen-
ces.
The active sequence flashes
Shows the outside temperature
Shows the status of the analog
outputs in [V].
Y1=3V, Y2=0V, Y3=not used
Shows the status of the relay
outputs Q1…Q3. (I=closed,
0=open).
Q1=closed, Q2=open, Q3=
open
Shows the status of the relay
outputs Q4…Q6. (I = closed, 0
= open)
This page only appears if the
plant works fine. Otherwise a
fault message is displayed.