Siemens SIMOTICS SD SH 71 315 Series User manual

OPERATING INSTRUCTIONS
SIMOTICS SD
Low Voltage Motors
1LE7
SH 71 ... 315
www.siemens.com/drives
Edition
04/2022

SIMOTICS SD
Low-Voltage Motors
1LE7 shaft heights 71 ... 315
Operating Instructions
04/2022
A5E51689275A-AA
Introduction 1
Safety information 2
Description 3
Preparing for use 4
Installation 5
Electrical connection 6
Commissioning 7
Operation 8
Maintenance 9
Spare parts 10
Disposal 11
Service & support A
Technical data B
Quality documents C

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens Limited
Digital Industries
Motion Control
R&D Technology Centre
Thane Belapur Road
Airoli Node
Navi Mumbai - 400 708
A5E51689275A-AA
P03/2022 Subject to change
Copyright © Siemens AG 2022.
All rights reserved

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 3
Table of contents
1 Introduction ........................................................................................................................................... 9
1.1 About these instructions ...................................................................................................... 9
1.2 My support ........................................................................................................................ 10
2 Safety information............................................................................................................................... 11
2.1 Information for those responsible for the plant or system................................................... 11
2.2 The 5 safety rules............................................................................................................... 11
2.3 Qualified personnel ........................................................................................................... 12
2.4 Safe handling .................................................................................................................... 12
2.5 Electromagnetic fields when operating electrical power engineering installations............... 14
2.6 Electrostatic sensitive devices ............................................................................................ 14
2.7 Electromagnetic compatibility............................................................................................ 15
2.8 Interference compatibility.................................................................................................. 15
2.9 Influence on the line power supply through a strongly irregular torque............................... 15
2.10 Interference voltages when operating the converter........................................................... 16
2.11 Special designs and construction versions .......................................................................... 16
3 Description........................................................................................................................................... 17
3.1 Area of application............................................................................................................. 17
3.2 Rating plates...................................................................................................................... 18
3.3 Installation ........................................................................................................................ 19
3.3.1 Cooling and ventilation...................................................................................................... 20
3.3.1.1 General ............................................................................................................................. 20
3.3.1.2 Motors with a fan .............................................................................................................. 20
3.3.1.3 Motors without a fan (optional) ......................................................................................... 21
3.3.2 Bearings ............................................................................................................................ 21
3.3.3 Balancing........................................................................................................................... 21
3.3.4 Types of construction/method of installation ...................................................................... 22
3.3.5 Degree of protection.......................................................................................................... 23
3.3.6 Environmental conditions .................................................................................................. 23
3.3.7 Optional built-on and built-in accessories ........................................................................... 23
4 Preparing for use ................................................................................................................................. 25
4.1 Safety-related aspects to consider when configuring the plant............................................ 25
4.2 Observing the operating mode........................................................................................... 25
4.3 Motors without final paint coating ..................................................................................... 25
4.4 Delivery ............................................................................................................................. 26

Table of contents
1LE7 shaft heights 71 ... 315
4Operating Instructions, 04/2022, A5E51689275A-AA
4.5 Transport and storage........................................................................................................ 26
4.5.1 Safety instructions for transport......................................................................................... 26
4.5.2 Transport........................................................................................................................... 29
4.5.3 Storage ............................................................................................................................. 29
4.5.4 Securing the rotor.............................................................................................................. 31
4.5.5 Commissioning after storage ............................................................................................. 33
4.5.5.1 Insulation resistance and polarization index ....................................................................... 33
4.5.5.2 Regreasing rolling bearings after storage periods of up to two years ................................... 33
4.5.5.3 Releasing the rotor shipping brace before commissioning .................................................. 33
4.6 Ensure adequate cooling.................................................................................................... 34
4.7 Interlock circuit for anti-condensation heating ................................................................... 36
4.8 Noise emission .................................................................................................................. 36
4.9 Voltage and frequency fluctuations during line operation................................................... 37
4.10 Rotational speed limit values.............................................................................................. 37
4.11 System-inherent frequencies.............................................................................................. 37
4.12 Electromagnetic compatibility............................................................................................ 38
4.13 Converter operation........................................................................................................... 39
4.13.1 Parameterizing the converter ............................................................................................. 39
4.13.2 Converter input voltage ..................................................................................................... 39
4.13.3 Reducing bearing currents during operation with converter (low voltage)........................... 40
4.13.4 Insulated bearings for converter operation ......................................................................... 41
4.13.5 Tandem operation ............................................................................................................. 42
5 Installation........................................................................................................................................... 43
5.1 Safety instructions for installation ...................................................................................... 43
5.2 Preparing for installation.................................................................................................... 44
5.2.1 Requirements for installation ............................................................................................. 44
5.2.2 Insulation resistance .......................................................................................................... 45
5.2.2.1 Insulation resistance and polarization index ....................................................................... 45
5.2.2.2 Checking the insulation resistance ..................................................................................... 45
5.2.3 Preparing the assembly area .............................................................................................. 47
5.2.4 Lift the motor to where it will be mounted and position it .................................................. 47
5.2.5 Motors with type of construction IM B15, IM B9, IM V8 and IM V9 ...................................... 48
5.2.6 Foot mounting .................................................................................................................. 48
5.3 Aligning and fixing the motor ............................................................................................ 49
5.3.1 Measures for alignment and mounting............................................................................... 49
5.3.2 Flatness of the supporting surfaces for conventional motors............................................... 50
5.3.3 Motor frame mounting feet (special design)....................................................................... 50
5.4 Installing the motor ........................................................................................................... 51
5.4.1 Preconditions for smooth, vibration-free operation............................................................. 51
5.4.2 Aligning the motor to the driven machine and mounting.................................................... 51
5.4.2.1 Selecting bolts................................................................................................................... 51
5.4.2.2 Horizontal types of construction with mounting feet .......................................................... 51
5.4.2.3 Horizontal types of construction with flange ...................................................................... 52
5.4.2.4 Vertical types of construction with flange........................................................................... 53
5.4.3 Removing the rotor shipping brace..................................................................................... 53
5.4.4 Recommended alignment accuracy.................................................................................... 53
5.4.5 Mounting the drive output elements.................................................................................. 54

Table of contents
1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 5
6 Electrical connection ........................................................................................................................... 57
6.1 Basic rules ......................................................................................................................... 57
6.2 Safety instructions for the electrical connection.................................................................. 58
6.3 Connecting the motor........................................................................................................ 59
6.3.1 Terminal box ..................................................................................................................... 60
6.3.1.1 Circuit diagram inside the terminal box cover ..................................................................... 60
6.3.1.2 Direction of rotation .......................................................................................................... 60
6.3.1.3 Terminal marking .............................................................................................................. 61
6.3.1.4 Cable entry ........................................................................................................................ 61
6.3.1.5 Versions ............................................................................................................................ 61
6.3.1.6 Protruding connection cables............................................................................................. 61
6.3.1.7 Connecting protruding cables ............................................................................................ 62
6.3.1.8 Minimum air clearances ..................................................................................................... 62
6.3.2 Cable glands...................................................................................................................... 63
6.3.3 Tightening torques ............................................................................................................ 65
6.4 Connecting the grounding conductor................................................................................. 65
6.5 Connecting a temperature sensor/anti-condensation heater ............................................... 66
6.6 Conductor connection ....................................................................................................... 67
6.6.1 Type of conductor connection............................................................................................ 68
6.6.2 Connecting aluminum conductors...................................................................................... 68
6.7 Connecting converters....................................................................................................... 69
6.8 Final checks....................................................................................................................... 70
7 Commissioning .................................................................................................................................... 71
7.1 Measures before commissioning ........................................................................................ 71
7.1.1 Checks to be carried out prior to commissioning................................................................. 72
7.1.2 Mechanical and electrical check ......................................................................................... 73
7.1.3 Converter operation........................................................................................................... 74
7.1.4 Insulation resistance and polarization index ....................................................................... 74
7.1.5 Testing the cooling of the motor ........................................................................................ 74
7.1.6 Commissioning a separately driven fan .............................................................................. 75
7.1.7 Further documents ............................................................................................................ 76
7.1.8 Setpoint values for monitoring the bearing temperature .................................................... 76
7.2 Switching on ..................................................................................................................... 77
8 Operation............................................................................................................................................. 79
8.1 Safety instructions for operation ........................................................................................ 79
8.1.1 Safety instructions relating to ventilation and cooling......................................................... 82
8.1.1.1 Safety instructions for forced ventilation (option)............................................................... 82
8.1.1.2 Safety instructions when operating motors with fan........................................................... 82
8.1.1.3 Motors with fan for the textile industry .............................................................................. 82
8.2 Switching on the motor ..................................................................................................... 83
8.3 Deactivating ...................................................................................................................... 83
8.4 Switching on again after an emergency switching-off......................................................... 83
8.5 Stoppages ......................................................................................................................... 84

Table of contents
1LE7 shaft heights 71 ... 315
6Operating Instructions, 04/2022, A5E51689275A-AA
8.5.1 Avoidance of damage to rolling bearings during stoppages ................................................ 85
8.5.2 Decommissioning the motor.............................................................................................. 85
8.5.3 Re-commissioning the motor ............................................................................................. 85
8.6 Faults ................................................................................................................................ 86
8.6.1 Inspections in the event of faults........................................................................................ 86
8.6.2 Electrical faults .................................................................................................................. 86
8.6.3 Mechanical faults............................................................................................................... 87
8.6.4 Rolling bearing faults......................................................................................................... 87
8.6.5 Faults on the separately driven fan..................................................................................... 88
9 Maintenance........................................................................................................................................ 89
9.1 Preparation and notes........................................................................................................ 89
9.2 Inspection and maintenance .............................................................................................. 90
9.2.1 Safety instructions for inspection and maintenance............................................................ 90
9.2.2 Inspections in the event of faults........................................................................................ 91
9.2.3 First inspection after installation or repair........................................................................... 91
9.2.4 General inspection............................................................................................................. 92
9.2.5 Assessing the rolling bearings ............................................................................................ 92
9.2.6 Maintenance intervals........................................................................................................ 93
9.2.7 Re-greasing ....................................................................................................................... 94
9.2.8 Cleaning............................................................................................................................ 95
9.2.9 Cleaning the fan cover of motors for the textile industry..................................................... 95
9.2.10 Drain condensate............................................................................................................... 96
9.2.11 Insulation resistance and polarization index ....................................................................... 96
9.2.12 Servicing the separately driven fan..................................................................................... 97
9.3 Corrective maintenance ..................................................................................................... 98
9.3.1 Rolling bearings................................................................................................................. 98
9.3.1.1 Bearing bushes ................................................................................................................ 100
9.3.1.2 Installing bearings ........................................................................................................... 100
9.3.2 Mounting dimension "x"................................................................................................... 102
9.3.3 Fan.................................................................................................................................. 102
9.3.4 Canopy, encoder under the canopy.................................................................................. 103
9.3.5 Tightening torques .......................................................................................................... 104
9.3.6 Screw lock washers.......................................................................................................... 104
9.3.7 Links................................................................................................................................ 104
9.3.8 Reassembly: Miscellaneous information ........................................................................... 104
9.3.9 Optional add-on units ...................................................................................................... 105
9.3.10 O-ring seal....................................................................................................................... 105
9.3.11 Encoder........................................................................................................................... 106
9.3.12 Grounding brush ............................................................................................................. 106
10 Spare parts......................................................................................................................................... 107
10.1 Part lists........................................................................................................................... 107
10.2 Exploded drawings .......................................................................................................... 108
11 Disposal ............................................................................................................................................. 113
11.1 RoHS - restricting the use of certain hazardous substances ............................................... 113
11.2 Information according to Article 33 of the REACH regulation ............................................ 114
11.3 Preparing for disassembly ................................................................................................ 114
11.4 Dismantling the motor..................................................................................................... 114
11.5 Disposal of components................................................................................................... 115

Table of contents
1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 7
A Service & support............................................................................................................................... 117
A.1 Siemens Service Center (Kalwa) ....................................................................................... 117
A.2 Siemens Industry Online Support ..................................................................................... 117
A.3 Further documents .......................................................................................................... 118
B Technical data.................................................................................................................................... 119
B.1 Configurator for drive technology .................................................................................... 119
B.2 Tightening torques .......................................................................................................... 119
B.2.1 Tightening torques for screw and bolt connections........................................................... 119
B.2.2 Terminal board and grounding......................................................................................... 120
B.2.3 Terminal boxes, end shields, grounding conductors, sheet metal fan covers ..................... 120
B.2.4 Tightening torques for electrical connections of monitoring equipment and anti-
condensation heating ...................................................................................................... 121
B.2.5 Tightening torques for cable glands ................................................................................. 121
B.3 Technical data and drawings............................................................................................ 122
B.3.1 Terminal box dimensions ................................................................................................. 122
B.3.2 Arrangement of the auxiliary terminal box ....................................................................... 123
C Quality documents ............................................................................................................................ 125
C.1 Quality documents SIMOTICS in SIOS ............................................................................... 125
Index .................................................................................................................................................. 127

Table of contents
1LE7 shaft heights 71 ... 315
8Operating Instructions, 04/2022, A5E51689275A-AA

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 9
Introduction
1
1.1 About these instructions
These instructions describe the motor and explain how to handle it, from initial delivery to
final disposal of the equipment. Keep these instructions for later use.
Read these operating instructions before you handle the motor and follow the instructions to
become familiar with its design and operating principles and thus ensure safe, problem-free
motor operation and long service life.
Safety instructions and handling-related warning notes are provided in these instructions.
When carrying out any activity at or with the motor, carefully comply with all of these notes
for your own safety, to protect other people and to avoid material damage.
Please contact the Service Center if you have any suggestions on how to improve this
document.
Text format features
You can find the following text format features in these instructions:
1. Handling instructions are always formatted as a numbered list. Always perform the steps in
the order given.
•Lists are formatted as bulleted lists.
–Lists on the second level are hyphenated.
Note
The note provides you with additional inf
ormation about the product itself, handling the
product - and the relevant documentation.

Introduction
1.2 My support
1LE7 shaft heights 71 ... 315
10 Operating Instructions, 04/2022, A5E51689275A-AA
1.2 My support
mySupport
Extensive assistance and more information can be found under the following link:
My Support Links and Tools
(https://support.industry.siemens.com/my/ww/en/documentation)
You can individually compile your personal library, e.g. for your documentation based on
Siemens content, and adapt it for your own motor documentation.
To do so, click "My Documentation".
Note
If you want to use this function, you must register once.
Later, you can log on with your login data.
You can create your own personal library under "mySupport" using the following procedure.
Precondition
You have registered for and logged on to "Siemens Industry Online Support", hereinafter
referred to as "SIOS".
SIOS (https://support.industry.siemens.com/cs/ww/en/)
Procedure for creating a personal library
1. Open SIOS and log on.
2. Enter the product you are looking for under "Search for product info" and press "Enter".
3. Select the doc. class you want, e.g. "Manual", under "Entry type".
4. Click on your desired manual under the entries.
5. Click on "Add to mySupport documentation".
6. Enter a title.
7. Press "OK".
❒
The selected manual can be found under "mySupport". To find further functions, click on the
icon located to the right of the document.
In this way, you can create your own library and quickly access your documentation.

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 11
Safety information
2
2.1 Information for those responsible for the plant or system
This motor has been designed and built in accordance with the specifications contained in
Directive 2014/35/EU ("Low-Voltage Directive") and IS 12615, and is intended for use in
industrial plants. Please observe the country-specific regulations when using the motor
outside India. Follow the local and industry-specific safety and setup regulations.
The persons responsible for the plant must ensure the following:
•Planning and configuration work and all work carried out on and with the motor is only to
be done by qualified personnel.
•The operating instructions must always be available for all work.
•The technical data as well as the specifications relating to the permissible installation,
connection, ambient and operating conditions are taken into account at all times.
•The specific setup and safety regulations as well as regulations on the use of personal
protective equipment are observed.
Note
Use the services and support provided by the local service center for planning, installation,
commissioning and service work.
2.2 The 5 safety rules
To ensure your own personal safety as well as to avoid material damage, always comply with
the safety-relevant instructions when carrying out any work. Also carefully comply with the 5
safety rules according to EN 50110-1 "Working in a no-voltage state" in the specified
sequence.
5 safety rules
1. Disconnect the system.
Also disconnect the auxiliary circuits, for example, anti-condensation heating.
2. Secure against reconnection.
3. Verify absence of operating voltage.
4. Ground and short-circuit.
5. Provide protection against adjacent live parts.
To energize the system, apply the measures in reverse order.

Safety information
2.3 Qualified personnel
1LE7 shaft heights 71 ... 315
12 Operating Instructions, 04/2022, A5E51689275A-AA
2.3 Qualified personnel
All work at the motor must be carried out by qualified personnel only. For the purpose of this
documentation, qualified personnel is taken to mean people who fulfill the following
requirements:
•Through appropriate training and experience, they are able to recognize and avoid risks
and potential dangers in their particular field of activity.
•They have been instructed to carry out work on the motor by the appropriate person
responsible.
2.4 Safe handling
Workplace safety depends on the attentiveness, care, and common sense of the personnel
who install, operate, and maintain the motor. In addition to the safety measures cited, as a
matter of principle, the use of caution is necessary when you are near the motor. Always pay
attention to your safety.
Also observe the following to prevent accidents:
•General safety regulations applicable in the country where the motor is deployed.
•Manufacturer-specific and application-specific regulations
•Special agreements made with the operator
•Separate safety instructions supplied with the motor
•Safety symbols and instructions on the motor and its packaging
Danger as a result of stationary parts under voltage (live parts)
Live parts represent a hazard. Touch protection against active (live) parts is no longer
guaranteed if covers are removed. The minimum clearance and creepage distances may be
violated when coming close to live parts. Touching or coming close to them can result in
death, serious injury or material damage.
•Ensure that all live parts are suitably covered.
•Switch off and disconnect the motor first if you want to remove covers. Observe the "5
safety rules" (Page 11).
Risk of injury due to rotating parts
Rotating parts are dangerous. Touch protection against rotating parts is no longer guaranteed
if covers are removed. Touching rotating parts can result in death, serious injury or material
damage.
•Ensure that all rotating parts are reliably covered.
•Switch off and disconnect the motor first if you want to remove covers. Observe the "5
safety rules" (Page 11).
•Only remove covers when the rotating parts have come to a complete standstill.

Safety information
2.4 Safe handling
1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 13
Risk of burns due to hot surfaces
Individual motor parts can become hot in operation. Burns can result when coming into
contact with these parts.
•Never touch motor parts during operation.
•Allow the motor to cool before starting work on the motor.
•Check the temperature of parts before touching them. If required, wear suitable protective
equipment.
Health hazard due to chemical substances
Chemical substances required for the setup, operation and maintenance of motors can
present a health risk.
•Observe the product information provided by the manufacturer.
Flammable substances hazard
Chemical substances required for the setup, operation and maintenance of motors may be
flammable. These substances can ignite if handled incorrectly. They can cause burns and
property damage.
•Observe the product information provided by the manufacturer.
Noise emissions
During operation, the motor's noise emission levels can exceed those permitted at the
workplace, which can cause hearing damage.
•Ensure that nobody is in the area of increased noise emissions during motor operation.
•Take steps to reduce noise so that the motor can be operated safely within your system.
The following measures may help to reduce noise.
–Covers
–Noise insulation
–Hearing protection measures
Prevention of hearing damage
If the permissible sound pressure level is exceeded, hearing damage can occur when
operating three-phase motors at their rated power. The permissible sound pressure level is
70 dB (A).

Safety information
2.5 Electromagnetic fields when operating electrical power engineering installations
1LE7 shaft heights 71 ... 315
14 Operating Instructions, 04/2022, A5E51689275A-AA
2.5 Electromagnetic fields when operating electrical power
engineering installations
Electrical power equipment generate electromagnetic fields during operation. Potentially
lethal malfunctions can occur in medical implants, e.g. pacemakers, in the vicinity of
electrical power equipment. Data may be lost on magnetic or electronic data carriers.
•Protect the personnel working in the plant by taking appropriate measures, such as
erecting identifying markings, safety barriers and warning signs and giving safety talks.
•Observe the nationally applicable health and safety regulations.
•It is forbidden for people with pacemakers to be close to the motor.
•Do not carry any magnetic or electronic data media.
2.6 Electrostatic sensitive devices
Material damage due to electrostatic discharge
Electronic modules contain components that can be destroyed by electrostatic discharge.
These components can be damaged or destroyed if they are not handled correctly. To protect
equipment against damage, follow the instructions given below.
•Only touch electronic modules if you absolutely have to work on them.
•The body of the person concerned must have been electrostatically discharged and
grounded immediately before any electronic modules are touched.
•Electronic modules should not be brought into contact with electrically insulating
materials, such as:
–Plastic film
–Plastic parts
–Insulating table supports
–Clothing made of synthetic fibers
•Always place electrostatic sensitive devices on conductive bases.
•Always pack, store and transport electronic modules or components in conductive
packaging, such as:
–Metallized plastic or metal containers
–Conductive foam material
–Domestic aluminum foil

Safety information
2.7 Electromagnetic compatibility
1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 15
The ESD protective measures required for components that can be destroyed due to
electrostatic discharge are shown in the following drawings:
a = conductive floor surface
b = ESD table
c = ESD shoes
d = ESD overall
e = ESD wristband
f = cabinet ground connection
2.7 Electromagnetic compatibility
This motor is designed in accordance with IEC/EN 60034, and when used as specified, it
complies with the requirements of European Directive 2014/30/EU regarding Electromagnetic
Compatibility.
2.8 Interference compatibility
By selecting suitable signal cables and evaluation units, ensure that the interference
immunity of the motor is not diminished.
2.9 Influence on the line power supply through a strongly irregular
torque
A strongly irregular torque, for example with the drive of a reciprocating motor, forces a non-
sinusoidal motor current. The emerging harmonics can have an impermissible influence on
the line power supply via the connection lines.

Safety information
2.10 Interference voltages when operating the converter
1LE7 shaft heights 71 ... 315
16 Operating Instructions, 04/2022, A5E51689275A-AA
2.10 Interference voltages when operating the converter
When a converter is in operation, the emitted interference varies in strength depending on
the converter (manufacturer, type, interference suppression measures undertaken). On
motors with integrated sensors (e.g. PTC thermistors), interference voltages caused by the
converter may occur on the sensor lead. This can cause faults which can result in eventual or
immediate death, serious injury or material damage.
•Comply with the EMC information provided by the manufacturer of the converter. This is
how you prevent the limit values stipulated by IEC/EN 61000-6-2 .... IEC/EN 61000-6-4 for
the drive system (consisting of the motor and converter) from being exceeded.
•You must put appropriate EMC measures in place.
2.11 Special designs and construction versions
Before carry out any work on the motor, determine the motor version.
If there are any deviations or uncertainty, contact the manufacturer, specifying the type
designation and serial number (see the rating plate), or contact the Service Center.

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA 17
Description
3
3.1 Area of application
WARNING
Risk of explosion
This motor is not designed for use in hazardous areas. An explosion can occur if the motor is
operated in these areas. This can result in death, serious injury or material damage.
•Never operate this motor in hazardous areas.
The rotating electrical motors of this series are used as industrial drives. They are designed for
a wide range of drive applications both for line operation as well as in conjunction with
frequency converters. They are characterized by their high power density, extreme
robustness, long service life and outstanding reliability.
Correct and intended use of the motors
These motors are intended for industrial installations. They comply with the harmonized
standards of the series EN / IEC 60034 (VDE 0530). It is prohibited to use these motors in
hazardous zones if the marking on the motor rating plate does not explicitly permit line or
converter operation. If other/more wide-ranging demands (e.g. protection so that they
cannot be touched by children) are made in special cases – i.e. use in non-industrial
installations – these conditions must be ensured by the customer.
Note
Motor directive
Low
-
voltage motors are components designed for installation in machines in accordance with
the current Machinery Directive. Commissioning is prohibited until it has been absolutely
identified that the
end product is in conformance with this Directive. Comply with standard
EN / IEC 60204-1.
Use of motors without CE marking
Motors without CE marking are intended for operation outside the European Economic Area
(EEA). Do not use any motors without a CE marking in the EEA!
Using motors without UKCA marking
Do not use any motors without UKCA marking in Great Britain (England, Wales and Scotland).

Description
3.2 Rating plates
1LE7 shaft heights 71 ... 315
18 Operating Instructions, 04/2022, A5E51689275A-AA
3.2 Rating plates
Rating plate
The rating plate shows the identification data and the most important technical data. The
data on the rating plate and the contractual agreements define the limits of proper usage.
Data on the rating plate
Item
Description
Item
Description
General data
Electrical data
1
Type of motor
31
Electrical data
2
Motor type
33
Rated voltage V
3
Serial number (incl. date of manufacture YY.MM)
34
Winding connections
4
Standards
35
Frequency Hz
5
Additional details (optional)
36
Rated power kW
6
Customer data (optional)
37
Rated current A
7
Country of origin
38
Power factor cosφ
9
Identification number of testing agency (optional)
39
Rated speed rpm
49
Company logo
40
Efficiency class
54
Crossed wheeled bin
41
Efficiency
55
ISI mask
Mechanical data
11
Frame size
17
Installation altitude (only if higher than 1000 m)
12
Type of construction
19
Bearing sizes
13
Degree of protection
20
Relubrication data/specifications (optional)
14
Motor weight kg
21
Brake data (optional)
15
Temperature class
24
Feather key arrangement
16
Ambient temperature range (optional)