Siemens HIPATH 2000 User manual

HiPath 2000
HiPath 3000
HiPath 4000
optiPoint WL 2 professional
Help for WebBasedManagement

Help topics
2
Help topics
About Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Home . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . . . . . . ..5
Login/Logout . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . . . .5
User Login / Admin Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Menu Status . . . . . . . . . . . . . . .. . . . . . . . . . . . . .. . . . .6
Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Menu User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Menu User. . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . . . .8
Profile Selection (User) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Handset PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Handset Settings
Handset Settings: Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Handset Settings: Ringer Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Handset Settings: Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Call Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Menu Admin . . . . . . .. . . . . . . . . . . . .. . . . . . . . .. . . .17
Network
Profile Selection (Admin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Profile Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
IP Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WLAN Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SRSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Dialling Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Enter LDAP Server Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Enter DLS Server Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Help topics
3
Enter Location Server Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
VPN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Quality of Service
Quality of Service(QoS): Protocol Settings . . . . . . . . . . . . . . . . . . . . . . 37
Quality of Service (QoS): Monitoring Settings . . . . . . . . . . . . . . . . . . . . 39
System Settings
Handset PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reset User Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Admin PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Handset Restart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
SNMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FTP-Transfer
Enter FTP Server Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
FTP Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
FTP Update Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
FTP Update LDAP Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
HTTP-Transfer
Local Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Local Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Factory Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Diagnostics
PING-Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
RTP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About Help
4
About Help
optiPoint WL2 professional Web Interface
You can use the Web Interface on your handset to set the handset according
to the user's specific requirements and to create and administer network
access profiles.
The following means of representation are used:
bold
User interface terms such as buttons, menus, and the names of input
fields.
ÆoptiPoint WL2 professional Web Interface
Links to another part of the Help or to Web pages on the Internet.
Click on the link to change to the specified topic. To return, select the
command Back in the Help pop-up menu. Open the pop-up menu by
right clicking on Help.
User > Handset Settings > Ringer Tones
Navigation to a Web Interface function (such as "Setting ringtones").
You can open the Web page by clicking on the User menu in the menu
bar, then on the function Handset Settings in the navigation area. After
that, under Handset Settings in the navigation are, select the subfunc-
tion Ringer Tones.
Link to the contents page at the end of each Help topic.
Searching in Help
Click inside the Help window and press the Ctrl and Fkeys. A search
dialogue box is opened. Enter the term you are looking for and click on OK.

Login/Logout
5
Home
You will find the entry Home in the navigation area of every Web page.
Click on Home to switch to the Status > Handset Web page. Logging out
takes place automatically.
Login/Logout
User Login / Admin Login
If your handset is protected by a Handset PIN and/or an Admin PIN, you
must log in when establishing a connection to the Web Interface.
The first time you click on one of the menus User or Admin a login dialogue
box is downloaded for you to enter a PIN.
A distinction is made as follows:
• Login is requested after you have clicked on User in the menu bar.
If you enter the Handset PIN, after establishing a connection you can
access all functions in the User menus. If an Admin PIN is assigned,
you cannot use the Admin menu.
If you enter the Admin PIN, you can access all Web Interface functions,
data and settings.
• The login page is opened after you have clicked on the Admin menu.
In this case you need to enter the Admin PIN. After this you can access
all Web Interface functions, data and settings.
Logging in
In the Your PIN field, enter the Handset PIN or the Admin PIN and click on
the Apply button. If the PIN is correct the first Web page for the menu
concerned is loaded. If the PIN is incorrect you will receive an appropriate
message.
If you have not assigned an Admin PIN, every subscriber to the
WLAN can access all the Web server functions (without logging in).
• If you enter the Handset PIN for the Web Interface wrongly three
times in a row, you can no longer log in with the handset PIN.
You then have the following options: click on the Admin menu,
log in with the admin PIN, and either reset the handset PIN or
reboot the handset.
• If you enter the Handset PIN wrongly on the handset three ti-
mes in a row, the handset will be blocked. In this case you have
to reset the Handset PIN via the Admin menu to cancel the
block. Rebooting does not cancel the block.

Menu Status
6
Logout
Navigation: Admin > Logout or User > Logout
If you click on Logout in the navigation area, you log out. The handset's
status screen (see ÆHandset) is displayed.
If you change from any Web Interface Web page to the Status menu,
logging out takes place automatically.
Menu Status
Handset
Navigation: Status > Handset
The properties and status of the handset are displayed:
Handset Name
The handset name is shown in the handset's idle display.
You can change the name (see ÆHandset Settings: Display). To do this,
open the Web page User > Handset Settings > Display.
Handset State
The following values are displayed:
–Idle
The handset is in idle status. You can access the Web Interface and
make settings.
– Active
You cannot access the Web Interface right now because a different
user is accessing the handset's Web Interface or because the handset
is not in idle status (e.g. a phone call is in progress or a menu is open
on the handset).
– Rebooting
The handset is being rebooted because, for example, you have reques-
ted a firmware update or a change to the network access profile. You
cannot access the Web Interface until the reboot has been completed,
i.e. when the status changes to Idle. When the status changes, the
Web page is automatically updated (reloaded).
MAC Address
The handset's device address. The MAC address is assigned by the manufac-
turer.
Firmware Version
Version of firmware that is currently loaded. Any firmware updates are
made available on the Internet. You can use the Web Interface to load
updates onto the handset. To do this, open the Web page ÆFTP Update
Firmware or ÆLocal Firmware Update.
Hardware Version
Handset device version.

Menu Status
7
File System
Navigation: Status > File System
Ringtones, pictures (screen pictures) and certificates, are stored in your
handset's file system.
In addition to the standard ringtones and pictures that are part of the
handset's scope of delivery you can save your own ringtones and pictures
(see ÆTransfer). You can use one of the pictures or photos as wallpaper
that is shown in the display when the handset is in idle status (see
ÆHandset Settings: Display).
You need ÆCertificates for WLANs that use authentication with EAP Type
TLS (see ÆWLAN Security).
Free
Amount of memory that remains for pictures, ringtones and certificates in
kByte.
Pictures
Amount of memory that is taken up by pictures.
Ringer Tones
Amount of memory that is taken up by ringer melodies.
Certificates
Amount of memory that is taken up by certificates loaded onto the
handset.
Relatedtopics
If you need to free up memory you can delete ringtones, pictures and certif-
icates you no longer need or else export them to your PC and store them
there, see ÆTransfer.

Menu Status
8
Menu User
Profile Selection (User)
Navigation: User > Profile Selection
The displayed list contains all network access profiles stored on the
handset. The most important WLAN settings for the profiles are displayed
(see ÆMeaning of WLAN settings messages displayed).
You can identify the profile that is currently active by the associated option
activated in the Active column.
You can change the profile, i.e. activate another profile or delete a profile.
Changing the network access profile – activating another
profile
In the list, click on the option associated with the profile in the Active
column and then on the Apply button.
The previously active profile is deactivated and, where applicable, your
connection to the Web Interface is terminated. The handset's status screen
is displayed. The handset reboots and registers with the access point using
the access data of the new profile. Once registration has been successfully
completed you can re-establish your connection with the Web Interface
providing your PC is still logged in to the same WLAN as the handset. To do
this, click on one of the menus.
Deleting a profile
The currently active profile cannot be deleted.
To delete a profile, click on the Delete button in the line of the profile. The
profile is deleted on the handset.
If the handset's IP address has changed, you must enter the new IP
address in the Web browser's address field to re-establish the
connection to the handset. You can display the new IP address on the
handset (see the user guide for the handset on the product CD).
If you want to delete the last/only (and therefore active) profile, you
can log on as the administrator and return the handset to its default
settings (see ÆFactory Reset). Please note that this will result in all
handset and network settings, all user data (phonebook, list of
internal subscribers etc.) and the handset and admin PIN being
deleted.

Menu Status
9
Meaning of WLAN settings messages displayed
Number
Current number of the profile in the list. It is possible to store up to 16
profiles on the handset. If there are already 16 profiles in the list you must
delete a profile before you can create a new one.
Profile Name
Name of the profile. The profile is displayed under this name in the list on
the handset.
You are advised to use the descriptive profile names from which you can
recognise the WLAN settings for which the profile is valid, e.g.
"Anna_Office". This makes it easier to select a profile from the profile
overview on the handset. For information on how to change the name of a
profile, see ÆProfile Name.
Network Name (SSID)
Service Set Identifier (SSID) of the WLAN (name for accessing the network).
Line Quality
For the active profile, the current reception strength is displayed for the
signals the handset is receiving from the access point/router. The trans-
mission power of the access point (max. 100 mW or 20 dBm) is "deadened"
by objects/walls within the transmission range and by the distance between
access point and handset.
Encryption
Encryption procedure used in the WLAN.
DHCP Client
Indicates whether the DHCP client is enabled or disabled.
If the DHCP client is enabled, the IP address of the handset is automatically
assigned by DHCP. The handset's IP address can change.
If the DHCP client is not enabled, a static IP address must be assigned to the
handset.
Active
You can identify the currently activated profile by the activated option in
the Active column.
Relatedtopics
• For how to create new profiles, see ÆProfile Selection (Admin)
• For editing a profile, see ÆProfile Selection (Admin)

Menu Status
10
Handset PIN
Navigation:
User > Handset PIN or Admin > System Settings > Handset PIN
You can protect your handset against unauthorised access with the Handset
PIN. It is requested when the handset is switched on and when the Web
Interface User menu is opened. Only persons who know the Handset PIN
can make calls on the handset or change the settings on the handset.
When supplied, there is no Handset PIN set in the handset.
You can enter a new Handset PIN, change a set Handset PIN, or delete the
Handset PIN.
Assigning a new Handset PIN
Enter four digits between 0 and 9 in the Handset PIN field. Click on Apply
to set the PIN. For security reasons, four dots are shown in the Handset PIN
field instead of the PIN.
Editing or deleting a Handset PIN
There are dots in the Handset PIN field, i.e a PIN has been assigned. If you
click in the Handset PIN field the contents of the field will be deleted.
• Click on the Apply button to delete the PIN. Your handset is no longer
protected against unauthorised access.
Or:
• Enter a new PIN and click on Apply. The new PIN is set.
During input, the PIN in the Handset PIN field is shown in plain text.
Once the PIN is set, for security reasons four dots are shown instead
of the PIN.
Change the Handset PIN regularly!
Access via the Admin menu is not protected by the Handset PIN. You
have to protect these settings with your own PIN, the Admin PIN. To
do this, open the Web page Admin > System Settings > Admin PIN.
Be sure to assign an ÆAdmin PIN! These should be different to the
Handset PIN.

Menu Status
11
Handset Settings: Audio
Navigation: User > Handset Settings > Audio
Setting advisory tones
You can switch your handset's various advisory tones on and off independ-
ently of one another by clicking on the relevant option (On or Off).
Key Click
Acknowledges each key press with a signal tone (beep).
Acknowledge Tones
There are the following acknowledge tones:
Confirmation tone (rising tone sequence) for successful entries/settings in
the menu and new entries in the calls list.
Error tone (descending tone sequence) for incorrect or impermissible
entries/settings on the handset.
Menu end tone when scrolling beyond the end of the menu.
Battery Warning
Signals (including during a call) that the battery is almost flat. The battery
requires charging.
Weak Signal Warning
Signals that the distance between the handset and access point is getting
too big, i.e. the reception strength is too low.
You cannot deactivate the signal tone for placing the handset in the
charging cradle.
Advisory tone volume
Using the Volume list, you can set the volume for the activated advisory
tones to 5 levels (1 = quiet to 5 = loud). The volume of the key click cannot
be adjusted.
Saving/rejecting settings
Click on the Apply button to store the changed settings on the handset.
Click on the Undo button if you want to reject the changes.

Menu Status
12
Handset Settings: Ringer Tone
Navigation: User > Handset Settings > Ringer Tones
Select the ringer melody with which incoming calls are to be signalled on
your handset, and specify the signal volume.
When the handset is supplied, standard ringtones are stored on the
handset. You can also download your own melodies from your PC onto the
handset and use them as the ringtone (see ÆTransfer).
Select ringer tone position
The list shows all ringtones stored on the handset. Select the ringtone
(sound) to be stored for each position (13-16). You cannot change the
ringtones for the positions 1-12.
Alarm
Ringer melody and volume for the handset's alarm clock.
To n e
All the melodies stored in the handset are shown in the list. Select the
melody (sound) that is to be used.
Volume
Select the volume for the ringtone. There is a choice of five volumes in the
list (1= quiet to 5 = loud) and the "crescendo" call (the volume increases
with each ring).
Saving/rejecting settings
Click on the Apply button to store the changed settings on the handset.
Click on the Undo button if you want to reject the changes.

Menu Status
13
Handset Settings: Display
Navigation: User > Handset Settings > Display
You can change the following settings for the display on the handset.
Handset Name
The handset name is shown in the handset's idle display.
You can change the name. It can be up to 16 characters long and can
contain letters, digits, special characters and spaces (e.g. Handset2: Anna).
Language
You can view the display texts on the handset (menus etc.) in different
languages. Open the list and select a language.
Wallpaper
You can display wallpaper when the handset is in idle status. The picture is
shown in the background behind the usual displays that appear in idle
status.
Click on the option Yes / No to switch the function on/off.
When the function is activated, a list is shown of the pictures and photos
stored on the handset. Open the list and select a picture. If you click on the
Preview button, the selected picture is shown in a separate window on
the PC.
You can also transfer pictures from the PC onto the handset (see
ÆTransfer).
Contrast, Brightness
You can adjust both the Contrast and Brightness of the display to 9 levels.
Open the list concerned and select a value between 1 and 9 (1 = low
contrast or dark, 9 = maximum contrast or maximum brightness).
Colour Scheme
Open the list and select a colour scheme for the display.
Night Mode
If the handset is in the charging cradle, the display is generally dimmed. If
this bothers you, you can set the handset to night mode (click on the option
On). The display is then completely dark when the handset is in the
charging cradle.
Click on the option Off to deactivate Night Mode.
Saving/rejecting settings
Click on the Apply button to store the changed settings on the handset.
Click on the Undo button if you want to reject the changes.

Menu Status
14
Call Settings
Navigation: User > Call Settings
You can make the following settings:
Easy Answer
When this function is activated, when a call arrives you can simply lift the
handset out of the charging cradle to be directly connected to the caller
without having to press the talk key.
Click on the option On / Off to switch the function on/off.
Saving/rejecting settings
Click on the Apply button to store the changed settings on the handset.
Click on the Undo button if you want to reject the changes.
Transfer
Navigation: User > Transfer > Ringer Tones / Pictures / Directory
You can transfer (import) ringtones and pictures from your PC to your
handset or export data from your handset to your PC and store it there. You
can back up the directory from your handset in a file in your PC.
You have the following options:
• Download ringtones and pictures (screen pictures) from the Internet on
your PC and use them on your handset.
• Back up ringtones and pictures you are not using at present on your PC
and delete them from your handset. This creates memory for other
things in your handset.
• Back up your directory on your PC and reload it in your handset when
required.
Select the item you wish to transfer in the navigation area: Ringer Tones /
Pictures / Directory

Menu Status
15
Transferring a ringtone/picture from the PC to the
handset
Carry out the following steps:
• In the upper section of the Web page, click on the Browse... button
and select the file you wish to transfer or enter the file name in the field
along with its complete path details.
The following file formats are supported:
– Ringtones: MIDI, SP-MIDI, iMelody, WAV
– Pictures: JPEG, BMP, GIF, PNG, WBMP (128 × 128)
•ClickontheImport button.
The ringtone or picture will be stored in the file system on the handset
providing there is sufficient memory (see ÆFile System).
Before the Import you can undo your entries using the Undo button.
Transferring a ringtone/picture from the handset to the PC
Open the list in the lower section of the Web page. All the ringtones and
pictures that are stored on the handset are shown. Select the file that is to
be transferred from the handset to the PC.
Click the Export... button. A browser-specific dialogue box is opened in
which you can specify the file directory and file name for the ringtone/
picture in the PC. Click on the Save button.
The selected file is stored on the PC.
Deleting a ringtone/picture
Open the list in the lower section of the Web page and select the ringtone/
picture that you wish to delete.
Click the Delete button. The selected file is deleted from the handset.
You cannot undo the delete by clicking on the Undo button!

Menu Status
16
Backing up/restoring the directory
Backing up the directory on the PC
In the lower section of the Web page, click on the Backup... button. A
browser-specific dialogue box is opened in which you can specify the
directory and file name for the exported directory. Click on the Save
button.
Restoring the directory
Carry out the following steps:
• In the upper section of the Web page, click on the Browse... and se-
lect the backup file from which you wish to restore the directory, or en-
ter the file name in the field along with its complete path details.
• Click the Restore button.
The imported directory replaces the one currently stored in the handset.
Before the Restore you can undo your entries using the Undo button.
• If you import the backup file for a directory, the directory current-
ly stored in the handset will be overwritten.
• Any voice pattern stored in the directory for voice dialling will be
lost during the transfer.

Menu Status
17
Menu Admin
Network
Profile Selection (Admin)
Navigation: Admin > Network > Profile Selection
You can store 16 network access profiles on your handset. In the profiles
you can specify the data for access to various access points (WLAN routers).
You therefore only need to activate another profile if, for example, you take
your handset from your home to your office.
A list is shown on the Web page containing all the network access profiles
stored in the handset.
The list contains the most important WLAN settings for the profiles (see
ÆMeaning of WLAN settings messages displayed). You can identify the
profile that is currently active by the associated option activated in the
Active column.
You can change the profile, i.e. activate another profile, create a new
profile and edit or delete an existing profile.
Changing the network access profile – activating another
profile
In the list, click on the option associated with the profile in the Active
column and then on the Apply button.
The previously active profile is deactivated and your connection to the Web
Interface is terminated. The handset's status screen is displayed. The
handset reboots and registers with the access point using the access data
of the new profile. Once registration has been successfully completed you
can re-establish your connection with the Web Interface providing your PC
is still logged in within the same WLAN as the handset.
If the handset's IP address has changed, you must enter the new IP
address in the Web browser's address field to re-establish the
connection to the handset. You can display the new IP address on the
handset (see the user guide for the handset on the product CD).

Menu Status
18
Creating a new profile, editing an existing profile
• In the upper section of the Web page, click on the New button to create
a new profile. If there are already 16 profiles stored on the handset you
must first ÆDeleting a profile before you can create a new profile.
• In the list, click on the Edit button next to a profile to edit this profile.
You can edit all the settings for the profile, including the profile name.
In both cases the Web page ÆProfile Name is opened automatically.
In the navigation area (the section on the left) a new level with subfunc-
tions is displayed under the Profile Selection function. The level contains
links to the Web pages in which you can make or edit the WLAN and
Gatekeeper settings.
You have the following options for making and editing settings:
• You can be guided through all the Web pages: in a Web page, click on
Apply and the next Web page is loaded automatically.
• If you just wish to adjust specific settings, in the navigation area, click
on the Web page you wish to load next.
If you click on the Apply button on a Web page, the settings made on this
Web page will be saved straight to the profile in the handset.
A new profile is created in the handset as soon as you click on the New
button. You can therefore stop creating a profile at any time and finish it at
a later point (editing a profile).
If you exit one of the Web pages without clicking on Apply only the
changes you have made on this Web page will be rejected.
Deleting a profile
The currently active profile cannot be deleted.
To delete a profile, click on the Delete button in the list next to the profile.
The profile is deleted on the handset.
To avoid unnecessary effort you can copy WLAN from other profiles
and edit them (see ÆProfile Name).
If you edit an active profile you must reboot the handset afterwards
(Admin > System Settings > ÆHandset Restart) to apply the
changes.
If you want to delete the last/only (and therefore active) profile, you
can return the handset to the default settings (see ÆFactory Reset).
Please note that this will result in all handset and network settings,
all user data (phonebook, list of internal subscribers etc.) and the
handset and admin PIN being deleted.

Menu Status
19
Profile Name
Navigation: Admin > Network > Profile Selection > New / Edit > Profile
Name
Specify the name under which the profile is to be displayed on the handset.
To avoid unnecessary work when creating or editing a profile you can copy
WLAN settings from other profiles stored in the handset. These settings are
then displayed in the fields on the relevant Web pages. You can make any
adjustments necessary.
Specify the following:
Profile Name
The name of the profile is displayed, or else a default name when a new
profile is created.
Enter the name under which you wish to store the profile in the handset.
If when creating a new profile you give it the name of a profile that already
exists, a second profile is created with the same name. The first profile is
not overwritten.
Copy IP and WLAN settings from
The profiles stored in the handset are shown in the list. Select the profile
from which you wish to copy the settings for WLAN access, the IP address
of the handset, and the routing.
The fields in the Web pages IP Addresses, IP Routing, WLAN and WLAN
Security will then be filled in with the appropriate values. You can adjust
them if necessary.
Copy Gatekeeper settings from
The profiles stored in the handset are shown in the list. Select the profile
from which you wish to copy the Gatekeeper settings.
The fields in the Web page Gatekeeper will then be filled in with the appro-
priate values. You can adjust them if necessary.
Saving/rejecting changes
Click on the Apply button if you wish to store the settings on this page.
Click on the Undo button if you want to reject the changes you have made.
Select meaningful profile names by which you can identify the
WLAN to which the profile applies, e.g. "Anna_Office". This makes it
easier to select a profile from the profile overview on the handset.
If when editing a profile you select a profile in Copy IP and WLAN
settings from and/or Copy Gatekeeper settings from and then
press on Apply, the WLAN and Gatekeeper settings of the profile you
wish to edit will be overwritten with the values of the selected profile.

Menu Status
20
IP Addresses
Navigation: Admin > Network > Profile Selection > New / Edit > IP
Addresses
Specify the IP address for the handset within the WLAN.
You have two options:
• An IP address is dynamically assigned to the handset. For this, the
DHCP Client must be activated at the access point/WLAN router of the
DHCP server and on the handset. The DHCP server (Dynamic Host
Configuration Protocol) assigns IP addresses to the network compon-
ents dynamically.
Please note: The IP address for the handset can change each time you
log in to the WLAN and sometimes while the handset is logged in to
the WLAN. You will find the current IP address in the header on each
Web page.
To activate the DHCP Client on the handset, click on the option Enable.
You then do not need to enter any further details for the addressing in
the WLAN. The settings for the WLAN router are used for the routing
and the preferred DNS server.
You can check the current IP address on the handset - see the user gui-
de for the handset on the product CD.
• A static IP address is assigned to the handset.
In this case you need to deactivate the DHCP Client on the handset.
This can be done by clicking on the option Disable.
The Web page is reloaded. You must specify the address information
for the handset described in the following section in the fields on the
Web page.
Entering static IP address and additional address information
The following details must correspond to the settings on the WLAN router.
Handset IP Address
When you specify the IP address of the handset, you should use an address
from an address block that is reserved for private use. This is generally the
range 192.168.0.0 – 192.168.255.254.
If the subnet mask 255.255.255.0 (seeabove) is set, then the first three
parts of the static IP address must be identical for all subscribers to your
WLAN.
Enter the IP address for your handset that is set at the WLAN router.
Subnet Mask
You should use 255.255.255.0 for the mask. If necessary, check the setting
at the WLAN router.