Siemens SITRANS F C MASSFLO MASS 2100 User manual

SITRANS F
Coriolis Flowmeters
MASS 2100 & FC300 (FCT030)
Operating Instructions
These Operating Instructions apply to Siemens
products
06/2017
A5E39789040-AA
Introduction 1
Safety notes 2
Description 3
Installing/mounting 4
Connecting 5
Commissioning 6
Operating MASS 2100/
FC300 with FCT030 7
Functions 8
Service and maintenance 9
Diagnosing and
troubleshooting 10
Technical data 11
Dimension drawings 12
Technical reference A
Default settings B
Certificates and support C
HMI menu structure D

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E39789040
Ⓟ 10/2017 Subject to change
Copyright © Siemens AG 2017.
All rights reserved

Table of contents
1 Introduction.................................................................................................................................................11
1.1 Document history...................................................................................................................11
1.2 Product compatibility..............................................................................................................12
1.3 Device documentation package.............................................................................................12
1.4 Items supplied........................................................................................................................13
1.5 Checking the consignment.....................................................................................................15
1.6 Security information...............................................................................................................15
1.7 Transportation and storage....................................................................................................16
2 Safety notes................................................................................................................................................17
2.1 Preconditions for safe use......................................................................................................17
2.2 Laws and directives................................................................................................................17
2.2.1 FCC Conformity.....................................................................................................................18
2.2.2 Conformity with European directives......................................................................................18
2.3 Requirements for special applications...................................................................................19
2.4 Use in hazardous areas.........................................................................................................20
2.4.1 Qualified personnel for hazardous area applications.............................................................20
2.4.2 Use in hazardous areas.........................................................................................................20
2.4.3 Loss of safety of device with type of protection "Intrinsic safety Ex i"....................................20
2.4.4 Installation in hazardous areas..............................................................................................21
2.4.5 Special conditions for safe use..............................................................................................23
2.4.6 Maximum temperature specifications for Ex use...................................................................24
3 Description..................................................................................................................................................27
3.1 Overview................................................................................................................................27
3.2 System configuration..............................................................................................................27
3.3 Design....................................................................................................................................28
3.3.1 Applications............................................................................................................................28
3.3.2 Versions.................................................................................................................................29
3.4 Features.................................................................................................................................32
3.5 Applications............................................................................................................................34
3.6 Approvals...............................................................................................................................34
3.7 Theory of operation................................................................................................................34
4 Installing/mounting......................................................................................................................................37
4.1 Basic safety notes..................................................................................................................37
4.1.1 Installation location requirements...........................................................................................39
4.1.2 Proper mounting.....................................................................................................................40
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 3

4.2 Installation instructions...........................................................................................................40
4.2.1 Sensor installation..................................................................................................................40
4.2.1.1 Determining a location ..........................................................................................................40
4.2.1.2 Orientation of the sensor........................................................................................................41
4.2.1.3 Mounting the sensor...............................................................................................................45
4.2.1.4 Hydrostatic testing..................................................................................................................47
4.2.1.5 Process pipe connection........................................................................................................48
4.2.1.6 Mounting a pressure guard....................................................................................................48
4.2.2 Transmitter installation...........................................................................................................50
4.2.2.1 Remote transmitter mounting.................................................................................................51
4.2.2.2 Turning the local display........................................................................................................53
4.2.2.3 Wall mount housing transmitter..............................................................................................54
4.3 Disassembly...........................................................................................................................56
5 Connecting.................................................................................................................................................57
5.1 Basic safety notes..................................................................................................................57
5.1.1 Energized devices..................................................................................................................61
5.1.2 Safety notes for connecting....................................................................................................61
5.1.3 Lack of equipotential bonding................................................................................................62
5.2 Connecting MASS 2100/FC300.............................................................................................62
5.2.1 Cable requirements................................................................................................................63
5.2.2 Connection safety information................................................................................................63
5.2.3 Connecting the multiple plug to the sensor............................................................................64
5.2.4 Transmitter power supply and I/Os connection......................................................................64
5.2.4.1 Step 1: Connecting the DSL and the transmitter....................................................................64
5.2.4.2 Step 2: Preparing for the transmitter connections..................................................................68
5.2.4.3 Connecting the Current HART, CH1......................................................................................70
5.2.4.4 Connecting the Modbus (CH1)...............................................................................................73
5.2.4.5 Connecting the Profibus (CH1)..............................................................................................74
5.2.4.6 Step 3: Connecting the power supply....................................................................................75
5.2.4.7 Connecting the power supply (with DSL)...............................................................................76
5.2.4.8 Step 4b: Connecting the inputs and outputs (channels 2 to 4)..............................................78
5.2.4.9 Step 5: Finishing the transmitter connection..........................................................................81
5.2.5 Ready for commissioning.......................................................................................................82
5.3 Wiring information..................................................................................................................82
5.3.1 Wiring in hazardous areas.....................................................................................................82
5.3.2 Signal wiring...........................................................................................................................82
5.3.3 Wiring.....................................................................................................................................83
5.4 Device nameplates.................................................................................................................84
5.4.1 Transmitter identification nameplate......................................................................................85
5.4.2 Sensor identification nameplate FC300.................................................................................89
6 Commissioning...........................................................................................................................................91
6.1 Basic safety notes..................................................................................................................91
6.1.1 Warnings................................................................................................................................93
6.2 General requirements............................................................................................................93
6.3 Local commissioning..............................................................................................................93
6.3.1 Power-up................................................................................................................................93
6.3.2 Local display..........................................................................................................................93
Table of contents
MASS 2100 & FC300 (FCT030)
4Operating Instructions, 06/2017, A5E39789040-AA

6.3.3 Initial startup...........................................................................................................................94
6.3.4 Commissioning via HMI.........................................................................................................95
6.3.4.1 Wizard introduction................................................................................................................95
6.3.4.2 Quick Commissioning wizard (menu item 1.1).......................................................................96
6.3.4.3 Zero point adjustment............................................................................................................97
6.3.4.4 Zero Point Adjustment wizard (menu item 1.2)......................................................................99
6.3.4.5 Wizards................................................................................................................................100
6.4 Commissioning with PDM....................................................................................................110
6.4.1 Operating via SIMATIC PDM...............................................................................................110
7 Operating MASS 2100/FC300 with FCT030............................................................................................111
7.1 Chapter overview Operating................................................................................................111
7.2 Operating instructions..........................................................................................................111
7.2.1 Local display (HMI)..............................................................................................................111
7.2.1.1 Display view structure..........................................................................................................113
7.2.1.2 Access control......................................................................................................................117
7.2.1.3 Operation view.....................................................................................................................118
7.2.1.4 Measurement views.............................................................................................................119
7.2.1.5 Operating views...................................................................................................................122
7.2.1.6 Alarm views..........................................................................................................................123
7.2.1.7 Diagnostic views..................................................................................................................125
7.2.1.8 Fixed display texts................................................................................................................126
7.2.1.9 Navigation view....................................................................................................................127
7.2.1.10 Parameter view....................................................................................................................129
8 Functions..................................................................................................................................................135
8.1 Process values.....................................................................................................................135
8.2 Zero point adjustment..........................................................................................................138
8.3 Low flow cut-off....................................................................................................................140
8.4 Empty tube monitoring.........................................................................................................140
8.5 Process noise damping........................................................................................................141
8.6 Inputs and outputs................................................................................................................143
8.6.1 Current output......................................................................................................................143
8.6.2 Pulse output.........................................................................................................................149
8.6.3 Frequency output.................................................................................................................150
8.6.4 Redundancy mode (frequency)............................................................................................151
8.6.4.1 Redundancy mode...............................................................................................................151
8.6.5 Digital output........................................................................................................................153
8.6.6 Input.....................................................................................................................................153
8.7 Totalizers..............................................................................................................................154
8.8 Dosing..................................................................................................................................155
8.8.1 Dosing control configuration.................................................................................................156
8.8.2 Valve control configuration...................................................................................................157
8.8.3 Dosing operation..................................................................................................................162
8.8.4 Fault handling.......................................................................................................................163
8.9 Audit trail logging..................................................................................................................163
8.10 Diagnostic log.......................................................................................................................163
Table of contents
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 5

8.11 Custom unit..........................................................................................................................164
8.12 SensorFlash.........................................................................................................................164
8.13 Datalogging on sensorFlash................................................................................................165
8.14 Process peak values on sensorFlash..................................................................................165
8.15 Simulation............................................................................................................................165
8.16 Maintenance.........................................................................................................................166
9 Service and maintenance.........................................................................................................................167
9.1 Basic safety notes................................................................................................................167
9.2 Recalibration........................................................................................................................168
9.3 Cleaning...............................................................................................................................169
9.4 Maintenance and repair work ..............................................................................................169
9.4.1 Service information..............................................................................................................171
9.5 Replacing the device............................................................................................................172
9.6 Return procedure.................................................................................................................172
9.7 Disposal...............................................................................................................................173
9.8 Spare parts/Accessories......................................................................................................173
9.8.1 Ordering of spare parts........................................................................................................173
9.8.2 Ex approved products..........................................................................................................173
9.8.3 Replaceable components.....................................................................................................174
9.8.4 Field Enclosure Spareparts..................................................................................................182
10 Diagnosing and troubleshooting...............................................................................................................185
10.1 Device status symbols.........................................................................................................185
10.1.1 Device status icons..............................................................................................................185
10.2 Fault codes and corrective actions.......................................................................................188
10.2.1 Sensor diagnostic events.....................................................................................................189
10.2.2 Transmitter diagnostic events..............................................................................................194
10.3 Operation troubleshooting....................................................................................................208
10.3.1 How do I copy application setup from one device to another?.............................................208
10.3.2 Troubleshooting sensor-related problems............................................................................209
10.3.3 How do I update the firmware?............................................................................................213
10.4 Diagnosing with PDM...........................................................................................................213
11 Technical data..........................................................................................................................................215
11.1 Power...................................................................................................................................215
11.2 Performance.........................................................................................................................215
11.3 Interface...............................................................................................................................218
11.3.1 Modbus interface..................................................................................................................218
11.3.2 HART interface.....................................................................................................................218
11.4 Inputs...................................................................................................................................219
11.4.1 Digital input..........................................................................................................................219
11.4.2 Process variables.................................................................................................................219
Table of contents
MASS 2100 & FC300 (FCT030)
6Operating Instructions, 06/2017, A5E39789040-AA

11.4.3 Input.....................................................................................................................................219
11.5 Outputs.................................................................................................................................220
11.5.1 Current output......................................................................................................................222
11.5.2 Pulse output.........................................................................................................................227
11.5.3 Frequency output.................................................................................................................228
11.5.4 Digital output........................................................................................................................229
11.5.5 Redundancy mode...............................................................................................................229
11.6 Construction.........................................................................................................................230
11.6.1 Local display (HMI)..............................................................................................................233
11.6.2 Cables and cable entries......................................................................................................233
11.7 Operating conditions............................................................................................................234
11.7.1 Rated operating conditions..................................................................................................234
11.8 Process................................................................................................................................235
11.8.1 Pressure drop curves...........................................................................................................235
11.8.2 Pressure drop.......................................................................................................................236
11.8.3 FC300 DN4..........................................................................................................................236
11.8.4 MASS2100 Di3, Di6 & Di15.................................................................................................237
11.9 Bus communication..............................................................................................................238
11.10 Approvals.............................................................................................................................239
11.11 SensorFlash.........................................................................................................................240
11.12 PED......................................................................................................................................241
11.13 Pressure - temperature ratings............................................................................................245
11.13.1 Pressure - temperature ratings (stainless steel sensors).....................................................246
11.13.2 Pressure - temperature ratings (Hastelloy sensors).............................................................248
12 Dimension drawings.................................................................................................................................249
12.1 Sensor dimensions...............................................................................................................249
12.2 MASS2100 DI3, DI6 & DI15.................................................................................................254
12.3 Transmitter dimensions........................................................................................................256
12.4 Mounting bracket..................................................................................................................257
A Technical reference..................................................................................................................................259
A.1 Sensor dimension dependent default settings.....................................................................259
A.1.1 Sensor dimension dependent default settings (Inputs/Outputs)..........................................269
B Default settings.........................................................................................................................................271
B.1 Sensor..................................................................................................................................271
B.2 Process Values....................................................................................................................273
B.3 Standard volume flow...........................................................................................................276
B.4 Totalizer...............................................................................................................................284
B.5 Inputs and outputs................................................................................................................291
B.6 Dosing..................................................................................................................................377
B.7 Date and time.......................................................................................................................403
Table of contents
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 7

B.8 Local display........................................................................................................................404
B.9 Maintenance and diagnostics...............................................................................................422
B.10 Audit Trail.............................................................................................................................465
B.11 Resets..................................................................................................................................466
B.12 Firmware update..................................................................................................................466
B.13 Communication....................................................................................................................466
B.14 Security................................................................................................................................476
B.15 Language.............................................................................................................................477
C Certificates and support............................................................................................................................479
C.1 Technical support.................................................................................................................479
C.2 QR code label......................................................................................................................479
C.3 Certificates...........................................................................................................................480
D HMI menu structure..................................................................................................................................481
D.1 Main menu...........................................................................................................................481
D.2 Menu item 2.1: Sensor.........................................................................................................483
D.3 Menu item 2.2: Process values............................................................................................484
D.4 Menu item 2.3: Totalizer.......................................................................................................487
D.5 Menu item 2.4: Inputs and outputs.......................................................................................488
D.6 Menu item 2.5: Dosing.........................................................................................................495
D.7 Menu item 2.7: Date and time..............................................................................................500
D.8 Menu item 2.8: Local display................................................................................................501
D.9 Menu item 3.1: Identification................................................................................................503
D.10 Menu item 3.2: Diagnostic events........................................................................................504
D.11 Menu item 3.3: Maintenance................................................................................................505
D.12 Menu item 3.4: Diagnostics..................................................................................................505
D.13 Menu item 3.5: Peak values.................................................................................................507
D.14 Menu item 3.6: Characteristics.............................................................................................507
D.15 Menu item 3.7: SensorFlash................................................................................................508
D.16 Menu item 3.8: Simulation....................................................................................................510
D.17 Menu item 3.9: Audit trail.....................................................................................................511
D.18 Menu item 3.10: Self test.....................................................................................................511
D.19 Menu item 3.11: Resets.......................................................................................................512
D.20 Menu item 3.12: Firmware update.......................................................................................512
D.21 Menu item 4: Communication..............................................................................................512
D.22 Menu item 5: Security..........................................................................................................514
Table of contents
MASS 2100 & FC300 (FCT030)
8Operating Instructions, 06/2017, A5E39789040-AA

Index.........................................................................................................................................................515
Table of contents
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 9

Table of contents
MASS 2100 & FC300 (FCT030)
10 Operating Instructions, 06/2017, A5E39789040-AA

Introduction 1
Note
This manual applies to the Coriolis flowmeter SITRANS FC MASS 2100 / FC300 with
transmitter FCT030, from firmware xx
This document are standard delivered in electronic media with the device. Latest version can
be downloaded at www.siemens.com (http://support.automation.siemens.com/WW/view/en/
60666565/134200)
These instructions contain all information required to commission and use the device. Read
the instructions carefully prior to installation and commissioning. In order to use the device
correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
1.1 Document history
The following table shows major changes in the documentation compared to the previous
edition.
Edition Remarks EDD version FW revision
02/2017 ● First edition
Use the device to measure process medium in accordance with the information in the
Operating Instructions.
Note
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas.
In a domestic environment this device may cause radio interference.
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 11

1.2 Product compatibility
Edition Remarks Product compatibility Compatibility of device integration package
06/2017 First revision HW revision 03
Compact FW revision 4.xx.xx-xx
Remote FW revision 4.xx.xx-xx
Service channel: SIMATIC
V8.2 Service Pack 1 or later
5.00.xx-xx
Modbus: SIMATIC V8.2 Serv‐
ice Pack 1 or later
5.00.xx-xx
HART: SIMATIC V8.2 Serv‐
ice Pack 1 or later
5.00.xx-xx
HART: SITRANS DTM V4.1 5.00.xx-xx
HART: AMS Device manager
V12
5.00.xx-xx
PROFIBUS: SIMATIC V8.2
Service Pack 1 or later
1.00.xx-xx
PROFIBUS: AMS Device
manager V12
1.00.xx-xx
PROFIBUS : SITRANS DTM
V4.1
1.00.xx-xx
1.3 Device documentation package
The user documentation package for this product includes the following documents
Document Purpose Intended users Availability
Operating Instruc‐
tions
Contains all information needed to
● check and identify the delivered
package
● install and electrically connect the
product
● commission the product, (setting
parameters via HMI menu)
● operate and maintain the device on a
daily basis
● troubleshoot and remedy minor
operation interruptions
Instrument techni‐
cians, plant opera‐
tors
● Available for download from
homepage
● Hardcopy can be purchased
via PIA Life Cycle Portal
(only English and German
versions)
Compact Operating
Instructions - Ex
Contains all information needed to
● satisfy the Special conditions for
installation of Ex-certified products
Instrument techni‐
cians, plant opera‐
tors with special
training in systems
for hazardous
areas.
● On documentation disk
● Available for download from
homepage
● Hardcopy can be ordered
via PIA Life Cycle Portal
Functions Manual Contains
● descriptions of all functions that can be
accessed via the local display (HMI)
● guide to setting parameters to obtain
optimum operation of the device
Instrument techni‐
cians, plant opera‐
tors
● Available for download from
homepage
Introduction
1.3 Device documentation package
MASS 2100 & FC300 (FCT030)
12 Operating Instructions, 06/2017, A5E39789040-AA

1.4 Items supplied
Flowsensors
● MASS 2100 DI 1.0, DI 1.5, DI 2.1
● Sensorprom or SensorFlash
● Calibration report
● Calibration certificate
Safety Note
Cal. rep.
● MASS 2100 DI 3, DI 6, DI 15
● Sensorprom or SensorFlash
● Calibration report
● Calibration certificate
Safety Note
Cal. rep.
● FC300 DN 4
● Sensorprom or SensorFlash
● Calibration report
● Calibration certificate
Safety Note
Cal. rep.
Flow transmitters:
● FCT010
● FCT030
● SIFLOW
● Calibration report
● Calibration certificate
Introduction
1.4 Items supplied
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 13

Compact systems
● Packet of cable glands
● Calibration report
● Calibration certificate
● SensorFlash
(installed in FCT030 transmiiter)
Safety Note
Cal. rep.
Remote system
● Remote field mount
● Packet of cable glands
● Calibration report
● Calibration certificate
Safety Note
Cal. rep.
● Remote wall mount
● Packet of cable glands
● Calibration report
● Calibration certificate
Safety Note
Cal. rep.
Note
Supplementary information
Supplementary product and production specific certificates are included on the SensorFlash®
SD card in the transmitter socket.
Note
Scope of delivery may vary, depending on version and add-ons. Make sure the scope of
delivery and the information on the nameplate correspond to your order and the delivery note.
Introduction
1.4 Items supplied
MASS 2100 & FC300 (FCT030)
14 Operating Instructions, 06/2017, A5E39789040-AA

1.5 Checking the consignment
1. Check the packaging and the delivered items for visible damage.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
● Do not use damaged or incomplete devices.
1.6 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines and
networks. Systems, machines and components should only be connected to the enterprise
network or the internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit:
http://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends to apply product updates as soon as available and to always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
http://www.siemens.com/industrialsecurity.
Introduction
1.6 Security information
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 15

1.7 Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
● Keep the original packaging for subsequent transportation.
● Devices/replacement parts should be returned in their original packaging.
● If the original packaging is no longer available, ensure that all shipments are properly
packaged to provide sufficient protection during transport. Siemens cannot assume liability
for any costs associated with transportation damages.
NOTICE
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
● Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical data
(Page 215).
The contents of this manual shall not become part of or modify any prior or existing agreement,
commitment or legal relationship. The sales contract contains all obligations on the part of
Siemens as well as the complete and solely applicable warranty conditions. Any statements
regarding device versions described in the manual do not create new warranties or modify the
existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.
Introduction
1.7 Transportation and storage
MASS 2100 & FC300 (FCT030)
16 Operating Instructions, 06/2017, A5E39789040-AA

Safety notes 2
2.1 Preconditions for safe use
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the specifications
relevant to safety.
Observe the information and symbols on the device. Do not remove any information or symbols
from the device. Always keep the information and symbols in a completely legible state.
Symbol Explanation
Consult operating instructions
Use the device only for flow measurement in accordance with this operating instruction and
observe the technical data.
WARNING
Improper device modifications
Risk to personnel, system and environment can result from modifications to the device,
particularly in hazardous areas.
● Only carry out modifications that are described in the instructions for the device. Failure
to observe this requirement cancels the manufacturer's warranty and the product
approvals.
Note
Functional safety applications (SIL)
If the device is used in a functional safety application, refer to the functional safety manual.
2.2 Laws and directives
Observe the safety rules, provisions and laws applicable in your country during connection,
assembly and operation. These include, for example:
● National Electrical Code (NEC - NFPA 70) (USA)
● Canadian Electrical Code (CEC) (Canada)
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 17

Further provisions for hazardous area applications are for example:
● IEC 60079-14 (international)
● EN 60079-14 (EC)
2.2.1 FCC Conformity
US Installations only: Federal Communications Commission (FCC) rules
WARNING
Improper device modifications
Danger to personnel, system and environment can result from improper modifications to the
device.
● Changes or modifications not expressly approved by Siemens could void the user’s
authority to operate the equipment.
Note
● This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
● This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the operating instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference to radio communications, in which case the user will be required to
correct the interference at his own expense.
2.2.2 Conformity with European directives
The CE marking on the device symbolizes the conformity with the following European
directives:
Electromagnetic
compatibility EMC
2014/30/EU
Directive of the European Parliament and of the Council on the harmoni‐
sation of the laws of the Member States relating to electromagnetic com‐
patibility
Low voltage direc‐
tive LVD
2014/35/EU
Directive of the European Parliament and of the Council on the harmoni‐
sation of the laws of the Member States relating to the making available
on the market of electrical equipment designed for use within certain volt‐
age limits
Safety notes
2.2 Laws and directives
MASS 2100 & FC300 (FCT030)
18 Operating Instructions, 06/2017, A5E39789040-AA

Atmosphère explosi‐
ble ATEX
2014/34/EU
Directive of the European Parliament and the Council on the harmonisa‐
tion of the laws of the Member States relating to equipment and protective
systems intended for use in potentially explosive atmospheres
Pressure equipment
directive PED
2014/68/EU
Directive of the European Parliament and of the Council on the approxi‐
mation of the laws of the Member States concerning pressure equipment
The applicable directives can be found in the EC conformity declaration of the specific device.
Note
CE declaration
The CE declaration certificate is available on the SensorFlash SD card delivered with the
device.
2.3 Requirements for special applications
Due to the large number of possible applications, each detail of the described device versions
for each possible scenario during commissioning, operation, maintenance or operation in
systems cannot be considered in the instructions. If you need additional information not
covered by these instructions, contact your local Siemens office or company representative.
Note
Operation under special ambient conditions
We highly recommend that you contact your Siemens representative or our application
department before you operate the device under special ambient conditions as can be
encountered in nuclear power plants or when the device is used for research and development
purposes.
Safety notes
2.3 Requirements for special applications
MASS 2100 & FC300 (FCT030)
Operating Instructions, 06/2017, A5E39789040-AA 19

2.4 Use in hazardous areas
2.4.1 Qualified personnel for hazardous area applications
Qualified personnel for hazardous area applications
Persons who install, connect, commission, operate, and service the device in a hazardous
area must have the following specific qualifications:
● They are authorized, trained or instructed in operating and maintaining devices and systems
according to the safety regulations for electrical circuits, high pressures, aggressive, and
hazardous media.
● They are authorized, trained, or instructed in carrying out work on electrical circuits for
hazardous systems.
● They are trained or instructed in maintenance and use of appropriate safety equipment
according to the pertinent safety regulations.
2.4.2 Use in hazardous areas
WARNING
Use in hazardous areas
Risk of explosion.
● Only use equipment that is approved for use in the intended hazardous area and labelled
accordingly.
2.4.3 Loss of safety of device with type of protection "Intrinsic safety Ex i"
WARNING
Loss of safety of device with type of protection "Intrinsic safety Ex i"
If the device has already been operated in non-intrinsically safe circuits or the electrical
specifications have not been observed, the safety of the device is no longer ensured for use
in hazardous areas. There is a risk of explosion.
● Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe
circuit.
● Observe the specifications for the electrical data on the certificate and/or in Technical
data (Page 215).
Safety notes
2.4 Use in hazardous areas
MASS 2100 & FC300 (FCT030)
20 Operating Instructions, 06/2017, A5E39789040-AA