Siemens SINAMICS Series User manual

+–
Power
Off
3
2
1
12
3
1
2
3
Quick Install Guide
Before mounting and commissioning
IMPORTANT: observe all documents enclosed with the device and the
SINAMICS CONNECT Operating Instructions before mounting and
connecting the device.
1. Push the device down.
2. Swing the device from below.
3. Push the device to the rail.
The device must only be connected to a 9 V DC to 36 V DC power
supply which meets the requirements of safe extra low voltage (SELV)
according to IEC/EN/DIN EN/UL 60950-1.
The power supply must meet the requirements of NEC Class 2 or LPS
according to IEC/EN/DIN EN/UL 60950-1.
If there are voltage peaks on power supply lines, use a protective device
in the form of a varistor (MOV) UMOV = U-rated × 1.2 (BLITZDUCTOR
BVT AVD 24 (918 422) or compatible).
The symbol indicates that you can refer to the Operating
Instructions manual for more information.
Note that the term "device" refers to a SINAMICS CONNECT unit.
Valid mounting orientation
Mounting
Scope of delivery
Connecting the power supply
Free space required around the device
Horizontal
Click
Wall mounting
Vertical
When the device is used in the area of Industrial Control Equipment in
accordance with UL 61010-2-201, note that the device is classified as
"Open Type". A UL 61010-2-201 conform enclosure is therefore a
mandatory requirement for approval or operation according to UL
61010-2-201.
Check the scope of delivery for completeness and intactness:
• One SINAMICS CONNECT device with one DC terminal block
mounted
• Quick Install Guide in English
Commissioning
Mounting
1. Guide a push-in lug
through the opening.
2. Press the push-in lug
down.
3. Drill the holes in the wall
and fasten the device to
the wall with screws and
anchors.
Power
Supply
Mounting on DIN rails
≥ 50 mm ≥ 50 mm
≥ 50 mm
≥ 50 mm
50 °C
0 °C
50 °C
0 °C
1
2
SINAMICS
SINAMICS CONNECT
1.1
A5E45421417-002
10/2018
1.3
1.4
1.2
2.1
9 V DC
to 36 V DC

+–
18
1
9
5
6
1
9
5
6
2
1
14
15
16
17
2
1
3
Switching on the device
9V DC
to 36 V DC
Power
Supply
Wiring example
Connecting example
Improper connection might cause high voltages. The LAN X2 connector
is designed for connection to a Local Area Network “Environment A”
according to IEEE802.3 or "Environment 0" according to IEC TR 62102
only.
• Do not connect the LAN X2 connector directly to the telephone
network or a WAN (Wide Area Network).
Safety notice for connections with LAN X2 connector
WARNING
Disclaimer of Liability
This document contains illustrations of the described devices and
accessories. The illustrations may deviate from the particularities of the
delivered device and accessories.
The SINAMICS CONNECT supports port modes of "Auto" and
"Manual" which you can set via the SINAMICS CONNECT Web
server. For more information, see Section "Configuring ports" in the
SINAMICS CONNECT Operating Instructions.
• Auto (default): Keep pressing the USER button for at least 1
second to identify the converter at the port, or wait (up to 5
minutes) for the device to identify the converter.
• Manual: You must set the basic parameters of the converter
manually via the Web server.
User documentation online
Central Technical Support
Service and spare parts
Illustrations
Connecting the converter
Interface assignment (converter side)
You can connect a SINAMICS CONNECT device to one of the
following converters via the RS232 interface on the converter
specific optional module or Control Unit:
• SINAMICS V20
• SINAMICS G120 series (G120D excluded)
• MICROMASTER 440
Interface assignment (device side)
Power
On
We have reviewed the contents of this publication to ensure consistency
with the hardware and software described. Since variance cannot be
precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary
corrections are included in subsequent editions.
Identifying the converter (optional)
Siemens AG
Digital Factory
Motion Control
Postfach 31 80
91050 ERLANGEN
Germany
To achieve better EMC performance, Siemens recommends that you
observe the following when connecting the device:
• Use the shielded cable for RS232 communication between the
converter and the device.
• Do not connect the device to the ground via the PE terminal (pin 1 at
X121, pin 17 at X122).
• Route the signal cables and the power cables separately in different
cable conduits.
Siemens recommends that you use the signal cable with a length less
than 3 m.
Note
Note
Cable shield
SINAMICS V20
BOP Interface Module
SINAMICS CONNECT
RJ45 connector
socket
RS232 interface
on the device
X121 X122
Description
Pin No.
Pin name
Pin No.
Pin name
1
PE
17
PE
Protective earth
2
PE4
16
PE8
Protective earth
3
M
15
M
Signal ground
4
RX4
14
RX8
Receive data
5
TX4
13
TX8
Transmit data
6
PE3
12
PE7
Protective earth
7
M
11
M
Signal ground
8
RX3
10
RX7
Receive data
9
TX3
9
TX7
Transmit data
10
PE2
8
PE6
Protective earth
11
M
7
M
Signal ground
12
RX2
6
RX6
Receive data
13
TX2
5
TX6
Transmit data
14
PE1
4
PE5
Protective earth
15
M
3
M
Signal ground
16
RX1
2
RX5
Receive data
17
TX1
1
TX5
Transmit data
117
Module
RS232 interface on
the module
Pin
No.
Signal
name
Description
BOP Interface Module
for SINAMICS V20
1
RXD
Receive data
2
TXD
Transmit data
3
GND
Signal ground
Control Unit for
SINAMICS G120 series
(G120D excluded)
2
RXD
Receive data
3
TXD
Transmit data
5
GND
Signal ground
PC converter connector
module for
MICROMASTER 440
2
RXD
Receive data
3
TXD
Transmit data
5
GND
Signal ground
...
...
1
2
3 M
RX1
PE1
PE
TX1
GND
TXD
RXD
15
16
14
1
X121
17
2.3
2.4
https://support.industry.siemens.com/sc/ww/en/sc
© Siemens AG 2018. All rights reserved
A5E45421417-002 10/2018
https://support.industry.siemens.com
https://support.industry.siemens.com/cs/ww/en/ps/25436/man
2.2
(≤ 12 N)