manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Siemens
  6. •
  7. Smoke Alarm
  8. •
  9. Siemens 5TC1292-7 User manual

Siemens 5TC1292-7 User manual

-4- -5-
Low baery mode
When the baery is running low, the smoke alarm will indicate this with a
repeve beep and flash for approximately 30 days. WARNING: This smoke
alarm is equipped with a non-replaceable baery. When this warning occurs,
replace the device as soon as possible! The acousc low baery warning
signal can be muted for ten hours by pressing the test buon. The smoke
alarm is sll funconing and able to detect smoke when it's in this mode.
Fault warning mode
When the smoke alarm is not funconing properly, it will turn into the fault
warning mode. Try cleaning the smoke alarm (see paragraph “Maintenance“)
or replace the smoke alarm!
Maintenance
•Test this smoke alarm weekly for correct operaon using the test facility. If
the smoke alarm funcons correctly, it will generate a loud beep. Due to
the loudness of the alarm, make sure that you always stand at arm’s length
distance from the unit when you are tesng. If the smoke alarm does not
generate an acousc signal, the smoke alarm must be replaced
immediately!
•Clean the smoke alarm at least once per month to remove dirt, dust or
debris. Use a vacuum cleaner with a so brush and vacuum all sides and
covers of the smoke alarm. Do not remove the top cover of the smoke
alarm to clean it inside.
•Do not aempt to repair this smoke alarm. If the smoke alarm shows a
damage related to its funconality, it must be replaced!
•Trouble shoong: False alarm is oen caused by dust or steam.
Recycling and disposal
The WEEE symbol means that this product and baeries must be
disposed separately from other household waste. When they reach
their end of life, take them to a designated waste collecon point in
your area to guarantee a safe disposal or recycling. Baeries must be removed
from the product by a qualified person, by opening the product. Protect the
environment, human health and natural resources!
EN SMOKE ALARM
User manual
5TC1292-7
Transport
Product is classified as a dangerous good, observe dangerous goods
regulaons!
hp://www.siemens.com/lowvoltage/dangerousgood hps://support.industry.siemens.com
Note: During the transport, the product must be deacvated. Remove the
mounng plate from smoke detector for deacvaon.
Service
Cerfied by AFNOR Cerficaon (www.afnor.org). For advise from experts and
firefighters, go to: hps://cerficaon.afnor.org/securite/nf- securite-
incendie-domesque.
The CE mark affixed to this product confirms its compliance with the
European Direcves which apply to the product and, in parcular, its
compliance with the harmonized specificaons of standard EN 14604:2005
relang to Construcon Products Regulaon 305/2011.
The NF – DOMESTIC FIRE SAFETY mark provides assurance as to safety and
consistent quality inspected by experts. Through its rigorous and exhausve
inspecons (holder's quality management system, product inspecons, audits
and monitoring tests, etc.), the NF mark represents a comprehensive
guarantee for consumers that the cerfied products are compliant. The NF –
DOMESTIC FIRE SAFETY mark confirms the product's compliance with
cerficaon rules NF 292.
ESSENTIAL CHARACTERISTICS: PASS
Nominal acvaon condions / sensivity / response delay (response me)
and performance under fire condions - Operang reliability - Tolerance to
supply voltage - Durability of operaonal reliability and response delay,
temperature resistance, vibraon resistance, humidity resistance, corrosion
resistance, electrical stability.
Siemens AG
Siemensstr. 10
D93055 Regensburg (Germany)
www.siemens.com
Idenficaon
Type of mounng Ceiling
Main power supply Internal to the device (baery)
Baery duraon of the
main power supply 10 years, seal not replaceable
Individual alarm indicator Yes
Suitable for installaon in
recreaonal vehicles Yes
Alarm silence facility Yes
Baery fault-forwarding at night Yes
Essenal cerfied features covered by the NF mark
20 5TC1292-7
0333 Smoke Alarm
EN 14604:2005 + AC:2008
DoP: 70782A-WA-DoP
hps://support.industry.siemens.com
Operang mode Visual signal (flash) Acousc signal (beep) Descripon mode
Normal 1 x per 40 seconds None Device is funconing properly
Test 1 x per second (3 x), pause of 1,5 seconds 1 x per second (3 x), pause of 1,5 seconds Device is being tested
Alarm 1 x per second (3 x), pause of 1,5 seconds 1 x per second (3 x), pause of 1,5 seconds Device has detected smoke
Alarm silence 1 x per 8 seconds None Smoke alarm is muted
Low baery 1 x per 40 seconds (simultaneously with beep) 1 x per 40 seconds (simultaneously with flash) Baery is running low
Low baery silence 1 x per 40 seconds None Low baery warning is muted
Fault warning 1 x per 40 seconds (alternang with beep) 1 x per 40 seconds (alternang with flash) Device is not funconing properly
Overview visual & acousc signals
R0
-1- -2- -3-
Thank you for purchasing our smoke alarm!
Please read these instrucons carefully and store them in a safe place during
the enre lifeme of the product.
Product descripon and intended use
This is a smoke alarm (delivered with baery) with an opcal sensor for
installaon in residenal buildings, apartments and rooms with residenal-
like use. Smoke alarms are designed to provide an early warning of fire smoke
and fires to persons present, so that these persons can react appropriately to
the hazardous event. Always consult local regulaons for smoke alarms.
Product specificaons
Detecon method: O pcal
Power supply : Sealed baery (3 V DC)
Baery lifeme : 10 years
Alarm volume : > 85 dB (A) at 3 meters
Alarm sensivity : 0,094 - 0,149 dB/m
Monitored area : max. 40 m²
Operang temperature : 0 °C - 40 °C
Operang humidity : < 93 %
Date of replacement : See product label
Individual alarm indicator : Yes
Alarm silence facility : Yes | Hush me: 5-15 minutes
Low baery warning : Yes
Low baery silence facility : Yes | Hush me : 10 hours
Installaon in leisure
accommodaon vehicles : Yes
Mounng locaon : Ceiling
Interconnectable : No
Warnings
•To prevent injury, this apparatus must be securely aached to the ceiling in
accordance with the installaon instrucons.
•Baeries should not be exposed to excessive heat such as sunshine, fire or
the like.
•Do not paint or cover the smoke alarm.
Where to install a smoke alarm
Smoke alarms must be installed in such a way that they can be reached
unhindered by the fire smoke so that fires can be reliably detected during the
development phase.
•Install at least in sleeping areas (especially children's rooms).
•Install at least in escape routes.
•In the middle of the ceiling of a room.
•At least 50 cm away from the wall and other objects.
•Maximum installaon height of 6 meter.
Where to install a smoke alarm in rooms
with special geometries
•Corridors with a maximum width of 3 m: Max. 15 m between 2 smoke
alarms. Max. 7,5 m to the front side of the gallery and smoke alarms
at edges/crossings of corridors.
•Rooms with sloping ceilings:
- If the ceiling inclinaon is > 20° to the horizontal: Smoke alarms must be
installed at least 0.5 m and at most 1 m from the ceiling top.
- Paral roof slopes: If the flat ceiling is ≤ 1 m wide, consider as ceiling
inclinaon is of > 20°. If the flat ceiling is >1 m wide,consider as flat
ceiling.
•Rooms with subdivided ceilings:
- Height of the subdivisions is ≤ 0.2 m: Beams without consideraon:
smoke alarm may be installed on the beams as well as on the ceiling.
- Height of subdivisions is > 0.2 m and if one of the ceiling panels > 36 m2:
a smoke alarm device should be installed in this ceiling panel and
addionally a smoke alarm device in the room, preferably in the middle
of the other ceiling panel
- Height of subdivisions > 0.2 m and area of ceiling panels ≤ 36 m²:
Individual ceiling panels are without consideraon. A smoke alarm must
be installed in a ceiling panel or on the joist, preferably in the middle of
the room.
Where not to install a smoke alarm
•In an environment with a high risk of draught (e.g. close to air condioning,
fans and venlaon outlets). The movement of air can impair the
penetraon of fire smoke into the smoke alarm.
•Areas where combusons regularly occurs, such as kitchens.
•Areas with high humidity such as bathrooms, or close to devices such as
dish washers or washing machines.
Acvaon
Before commissioning the smoke alarm, it is important to acvate it and test
it for correct operaon.
•Place the mounng plate on the smoke alarm and secure it by turning it
clockwise. When it’s properly ghtened, the smoke alarm is acvated by
the acvaon switch and generates a loud beep.
•Test the correct acvaon of your smoke alarm by pressing the test buon.
If no sound is generated, the smoke alarm is not acvated properly and
should not be used!
For a reliable test, press test buon for around 10 seconds, unl two
sequences of 3 beeps are generated, and release.
•It is recommended to write the replacement date (10 years) on the label, in
a calendar or in an easily verifiable place.
Mounng
•Remove the mounng plate from the smoke alarm.
•Place the mounng plate on the desired installaon locaon and mark
where the holes should be drilled.
•Drill two holes with a diameter of 5 millimetres.
•Push the plasc plugs into the holes.
•Insert the screws into the mounng plate, and ghten them firmly into the
plugs.
•Place the smoke alarm on the mounng bracket and secure it by turning it
clockwise.
•When it's properly ghtened, the smoke alarm generates a beep.
•Test the correct operaon of your smoke alarm by pressing the test buon.
If no sound is generated, the smoke alarm is not funconing properly and
should not be used!
Alarm silence facility
When the smoke alarm has detected smoke and turns into the alarm mode,
you can mute the alarm for a minimum of 5 minutes and a maximum 15
minutes by pressing the test buon. Aer that, the smoke alarm
automacally resets and returns into the normal operaon mode. If there are
sll parcles of combuson in the air, the smoke alarm will turn into the alarm
mode again. WARNING: Before using the alarm silence facility, always idenfy
the cause of the alarm and make sure that the circumstances are safe.
Ceiling
Mounng plateMounng plateMounng plate
Hobby room
Boiler room
Kitchen
Children’s roomBedroom
Ac
Escape
Escape
Escape
Livingroom
Opmal Restricted
Test buon
Sound output
LED indicator
Acvaon switchAcvaon switchAcvaon switch

Other Siemens Smoke Alarm manuals

Siemens FDOT421 User manual

Siemens

Siemens FDOT421 User manual

Siemens DELTA reflex SD230N Service manual

Siemens

Siemens DELTA reflex SD230N Service manual

Siemens Synco living AP260 User manual

Siemens

Siemens Synco living AP260 User manual

Siemens ILI-1 User manual

Siemens

Siemens ILI-1 User manual

Siemens FCI2016-U1 Guide

Siemens

Siemens FCI2016-U1 Guide

Siemens OH921 User manual

Siemens

Siemens OH921 User manual

Siemens FDA241 User manual

Siemens

Siemens FDA241 User manual

Siemens DM1101 User manual

Siemens

Siemens DM1101 User manual

Siemens Cerberus Pyrotronics PB-1191 User manual

Siemens

Siemens Cerberus Pyrotronics PB-1191 User manual

Siemens 5TC1292-6 User manual

Siemens

Siemens 5TC1292-6 User manual

Siemens AD1-C11 User manual

Siemens

Siemens AD1-C11 User manual

Siemens FDA2 Series Technical manual

Siemens

Siemens FDA2 Series Technical manual

Siemens DB-ADPT User manual

Siemens

Siemens DB-ADPT User manual

Siemens OP921 User manual

Siemens

Siemens OP921 User manual

Siemens DOW1171 User manual

Siemens

Siemens DOW1171 User manual

Siemens DB721-CN User manual

Siemens

Siemens DB721-CN User manual

Siemens FDA241 Technical manual

Siemens

Siemens FDA241 Technical manual

Siemens Cerberus DLO1191 User manual

Siemens

Siemens Cerberus DLO1191 User manual

Siemens DELTA reflex SD230N Service manual

Siemens

Siemens DELTA reflex SD230N Service manual

Siemens FDBZ292 User manual

Siemens

Siemens FDBZ292 User manual

Siemens DOW1171 User manual

Siemens

Siemens DOW1171 User manual

Siemens Cerberus DLO1191 Guide

Siemens

Siemens Cerberus DLO1191 Guide

Siemens DELTA Reflex SD9 Service manual

Siemens

Siemens DELTA Reflex SD9 Service manual

Siemens AD2-C11 User manual

Siemens

Siemens AD2-C11 User manual

Popular Smoke Alarm manuals by other brands

Tyco SB manual

Tyco

Tyco SB manual

System Sensor 2112 Installation and maintenance instructions

System Sensor

System Sensor 2112 Installation and maintenance instructions

Sontay SD-D quick start guide

Sontay

Sontay SD-D quick start guide

First Alert SA300 user manual

First Alert

First Alert SA300 user manual

INIM Electronics V200 quick start guide

INIM Electronics

INIM Electronics V200 quick start guide

UltraFire UBH1RF user manual

UltraFire

UltraFire UBH1RF user manual

Bosch FAS-420-TM Quick installation guide

Bosch

Bosch FAS-420-TM Quick installation guide

Radal Technology CSA-S5B installation guide

Radal Technology

Radal Technology CSA-S5B installation guide

Kidde 19HI owner's manual

Kidde

Kidde 19HI owner's manual

GE ESL 700 Series installation instructions

GE

GE ESL 700 Series installation instructions

Longsin LS-828-27 manual

Longsin

Longsin LS-828-27 manual

Ateis VELOX LV100 manual

Ateis

Ateis VELOX LV100 manual

FlameStop VESDA-E VEU-A10 Product guide

FlameStop

FlameStop VESDA-E VEU-A10 Product guide

System Sensor B210LP Installation and maintenance instructions

System Sensor

System Sensor B210LP Installation and maintenance instructions

usi 2995 instructions

usi

usi 2995 instructions

Elektrotechnik Schabus GX-D500P operating instructions

Elektrotechnik Schabus

Elektrotechnik Schabus GX-D500P operating instructions

American Sensor SA379 instruction manual

American Sensor

American Sensor SA379 instruction manual

Trox EK-JZ Installation and operating manual

Trox

Trox EK-JZ Installation and operating manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.