Silver Cross SURF User manual

SURF
IMPORTANT: KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE

2
These instructions are
important.
Read these instructions before use and keep
them for future reference.Your child’s safety
may be aected if you do not follow these
instructions.
Your Surf Pushchair and carrycot is a high
quality Silver Cross product. It meets current
British and European safety standards and
care and regular light maintenance will
ensure long service.
This pushchair is suitable from birth up to
9kg with the Carrycot and from 6 months up
to 15 kg using the Seat Unit.
If somebody unfamiliar is using your Surf
Pushchair always ensure that they read
these instructions carefully so that they
understand how the product works best.
The Surf Pushchair is designed and tested
to be used with the Ventura Plus S Car Seat
and Simplicity Infant Carrier and the Surf
Essentials pack all sold separately.
Always read all the instructions provided
carefully and remember, the safety of your
child is your responsibility.
WARNING: It may be dangerous
to leave your child unattended.
Contents
First check all your parts have been
supplied. Your Surf Pushchair includes:
1.1 Surf seat unit with harness
1.2 Chassis
1.3 Bumper bar
1.4 Rain cover
1.5 Rear wheels
1.6 Front wheels
1.7 Simplicity Adaptors
1.8 Cup holder
1.9 Shopping basket
1.10 Carrycot mattress and cover
1.11 Carrycot outer
1.12 Carrycot liner
1.1
1.3
1.2
1.5
1.6
1.9
1.8
1.121.11
1.10
1.7
1.4

3
silvercrossbaby.com
Preparation for use
Remove all packaging material from your
Surf Pushchair. To use your Surf Pushchair
from birth you must use the Silver Cross
the Carrycot (included).
WARNING: Check that the
carrycot or seat unit is correctly
engaged before use.
Surf chassis
2.1 Attach the front and back wheels by
inserting the axles into the Surf frame
until they ‘click’ into position.
2.2 Release the folding lock and lift the
handle to waist height.
2.1
2.2

4
Surf chassis (continued)
2.3 Lift the handle upwards and ick
forwards, while holding the handle
tightly, the frame ‘clicks’ and locks
into position. Always check that the
frame is secure.
2.4 Apply the brake (see point 23.1) and
adjust the handle height by pushing
the adjustment button in. Slide the
handle
up or down and release the
adjustment
button. The handle will lock and ‘click’
into position.
Your Surf chassis is now ready for use.
2.3
2.4

5
silvercrossbaby.com
Using your Surf from birth with
the carrycot.
Remove all packaging material from your
Surf Carrycot.
3.1 First erect the carrycot outer. Lay the
carrycot outer down with frame upper
most. Press the 2 x metal bars into the
locators on internal base of carrycot.
A small groove in the locator holds the
frame in position.
3.2 Attach the carrycot liner to the
carrycot outer. Fasten each inner zip.
There is one at each end of the liner.
3.3 Pass the two D-shaped parts of the
liner between the liner and the outer
and fasten the velcro patches to secure
the liner in place.
3.4 Place the mattress into the base of
the liner.
3.5 Zip your Surf hood to the zip on the
carrycot outer.
3.6 Attach the hood to the frame by
pressing down on the hood attachment
clips on each side of frame.
3.7 To t the apron, place the apron over
the top of the carrycot. Secure in place
by sliding the apron clips over the
attachment points inside the
carrycot frame.
NOTE: The Apron comes in 2 parts. To use
the apron with the carrycot, the lower
part of the apron will need to be zipped
o rst. Please keep the lower part in a
safe place.
WARNING: ONLY USE ON A FIRM,
HORIZONTAL LEVEL AND DRY
SURFACE.
CAUTION: The head of the child
in the carrycot should never be
lower than the body of the child.
3.1
3.4
3.5 3.6
3.7
3.2
3.3

6
Using your Surf from birth with
the carrycot. (continued)
3.8 Slide the apron ap clips over the
attachment points on the inside of
the carrycot frame.
3.9 Attach the bumper bar by pressing
the ends of the bumper bar into the
attachment points of the carrycot
frame. Wait to hear them ‘click’
into place. Lift gently to ensure the
bumper bar is locked in place. Fold
the apron ap over the bumper bar,
the magnets hidden inside the ap
will hold it in place.
NOTE: The bumper is to be used on the Surf
Pushchair and the Surf Carrycot
WARNING: Please ensure the
bumper bar is fully locked in
place whenever lifting your child
in the carrycot. Your child’s
safety is your responsibility.
WARNING: Ensure all locking
devices are engaged before use.
Your Surf Carrycot is ready to use.
3.8
3.9

7
silvercrossbaby.com
Attaching the carrycot to your
chassis
4.1 To attach your Surf Carrycot to
the Surf chassis hold the carrycot
above the chassis. Locate the
carrycot chassis connector onto
the attachment post of the chassis.
Ensure the carrycot ‘clicks‘ into
place. The carrycot should be tted
rearward facing. Lift the carrycot
gently by the bumper bar to check it
has locked into place.
WARNING: Do not add a
mattress other than the one
provided.
Detaching the carrycot from
your chassis
4.2 With the Surf Carrycot facing you
press the red release button rst
located on the side of the carrycot
until it clicks into place.
WARNING: This button is
now unlocked. It will re-lock
automatically when the
carrycot is re-attached to the
chassis.
Then while pressing and holding the other
black release button on the opposite side
of the carrycot, lift the carrycot from the
chassis using the bumper bar.
WARNING: Always ensure your
bumper bar is attached when
your child is in the carrycot.
The carrycot will now lift clear of the chassis.
4.1
4.2

8
Using your bumper bar on the
carrycot
Your Surf Carrycot uses the same Surf
bumper bar as your seat unit. It can be
fully or partly removed.
5.1 To attach, simply press both ends of
the bumper bar into the connector
points on the seat unit. Wait for it to
‘click’ in place.
5.2 To detach, press the bumper bar
release button on the carrycot frame
with one hand and pull the bumper
bar away from the connector point
with the other hand. The bumper bar
will rotate.
To detach both sides repeat point (5.2)
above. With one side of the bumper
bar removed the carrycot is easily
accessible.
WARNING: The bumper bar
must be securely connected
at all times when in use. The
safety of your child is your
responsibility.
Using your hood on the carrycot
6.1 Zip the back of the Surf hood to the
top of the Surf Carrycot frame taking
care to engage the zip properly.
6.2 Your Surf hood ts to the carrycot
frame by pressing the hood clips
down onto the frame below the round
black plastic locator.
6.3 Your Surf hood can be used in 4
positions. Fully open, semi-open,
semi-open with viewing window, and
fully covered.
5.2
5.1
6.1 6.2
6.3

9
silvercrossbaby.com
7.1
7.2
8.1
Using your apron on the
carrycot
7.1 First detached the Surf apron lower
section using the zip on the front of
the apron and place over the top of
the carrycot.
NOTE: Please ensure you keep
the apron lower section in a safe
place, as you will need it when
using the Surf as a pushchair.
7.2 Secure in place by sliding the apron
clips over the attachment points
inside the carrycot frame and fold
the apron ap over the bumper bar
using the hidden magnets to secure
in place.
Using your carrycot liner &
mattress
8.1 Your Surf Carrycot mattress is
removable. Simply lift it out of the
liner. The mattress cover can be hand
washed. Remove the foam mattress
insert prior to washing by opening
the ap on the back of the mattress
cover and removing the foam
mattress.
The Surf Carrycot has a removable
liner. Simply unzip each end and
release the Velcro fastenings to
remove it.
To t the liner and mattress see
preparation for use points (3.1-3.4).
The liner can be hand washed. (The
boards should be removed using the
zip on the back prior to washing)

10
Using your raincover on the
carrycot
9.1 Your Surf raincover should be used
when the Surf hood is attached to the
carrycot. First slide over the hood and
down towards the foot of the carrycot
and over the apron.
NOTE:This raincover can be used on
both the Carrycot and the Seat Unit.
A zip gives easy access to your child.
Using your Surf as a pushchair
10.1 Your Surf seat unit can be tted
to the chassis in rearward facing
position (infant facing you) or
forward facing position (infant facing
away from you). Follow point (4.1) to
attach the seat unit to the chassis
Adjust the seat unit to the desired
position. See point (20.1). Secure
the apron see point (17.1). Your Surf
Pushchair is ready to use.
10.1
9.1