Simoco SDM610 User manual

SDM610 MOBILE RADIO
USER MANUAL
TNM-U-E-0109, Issue – 1.3
October 2013
Field House,
Uttoxeter Old Road
Derby
DE1 1NH
Tel: [phone]
FAX: [phone]
http://www.simocogroup.com
1270 Ferntree Gully Road,
Scoresby
Victoria, 3179
Australia
Tel: [phone]
FAX: [phone]
http://www.simocogroup.com
©Simoco 2013

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 2 PREFACE
PREFACE
D ECLARATION
This User Manual covers the Digital Mobile Radio (DMR) Operating Instructions for the SDM610
Portable Radio Transceiver.
Any performance figures quoted are subject to normal manufacturing and service tolerances. The
right is reserved to alter the equipment described in this manual in the light of future technical
development.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
C OPYRIGHT
All information contained in this document is the property of Simoco and specifically ComGroup
Australia. All rights are reserved. This document may not, in whole or in part, be copied,
photocopied, reproduced, translated, stored, or reduced to any electronic medium or machine-
readable form, without prior written permission from Simoco.
C OMPUTER S OFTWARE C OPYRIGHTS
The AMBE+2
TM
voice coding Technology embodied in this product is protected by intellectual
property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc.
This voice coding Technology is licensed solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile,
reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos. #6,912,495 B2, #6,199,037 B1, #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
D ISCLAIMER
There are no warranties extended or granted by this document. Simoco accepts no responsibility
for damage arising from use of the information contained in the document or of the equipment and
software it describes. It is the responsibility of the user to ensure that use of such information,
equipment and software complies with the laws, rules and regulations of the applicable
jurisdictions.
E QUIPMENT AND M ANUAL U PDATES
In the interests of improving the performance, reliability or servicing of the equipment, Simoco
reserves the right to update the equipment or this document or both without prior notice.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 3 PREFACE
E RRORS AND O MISSIONS
The usefulness of this publication depends upon the accuracy and completeness of the information
contained within it. Whilst every endeavour has been made to eliminate any errors, some may still
exist. It is requested that any errors or omissions noted should be reported to either of the
following who are part of the Simoco group:
Field House
Uttoxeter Old Road, Derby.
DE1 1NH. UK
1270 Ferntree Gully Road, Scoresby
Victoria. 3179
Australia
Tel: [phone] Tel: [phone]
E-mail: custo[email protected] E-mail: inquiry[email protected]
D OCUMENT H ISTORY
Issue Date Comments
1.0 January 2013 Initial Issue.
1.1 July 2013 Changes to Support email addresses.
1.2 August 2013 Simoco Australasia Customer Support Telephone number change.
1.3 October 2013 Details of Technical Support Ticket System added to Support
page.
R ELATED D OCUMENTS
1. TNM-U-E-0111. SDM610 DMR User Guide.
2. TNM-I-E-0038. SDM600 Installation Sheet.
To order printed copies of this or any of the above publications, please contact Simoco. See the
Support page for contact information.
A comprehensive list of documentation is available for download on the Simoco website
http://www.simocogroup.com via the Partner Portal.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 4 CONTENTS
TABLE OF CONTENTS
Page
Title Page ...................................................................................................................................... 1
Preface .......................................................................................................................................... 2
Table of Contents (This List) ....................................................................................................... 4
List of Figures .............................................................................................................................. 6
List of Tables ................................................................................................................................ 6
Personal Safety ............................................................................................................................ 7
Compliance with RF Energy Exposure Guidelines (United States and Canada) ..................... 9
General Notes ............................................................................................................................ 13
Simoco Support ......................................................................................................................... 14
Abbreviations ............................................................................................................................. 17
Glossary ..................................................................................................................................... 18
1 INTRODUCTION ................................................................................................................. 18
1.1 O VERVIEW ........................................................................................................................ 18
1.2 C ONFIGURATION ............................................................................................................... 18
1.3 I NSTALLATION .................................................................................................................. 18
1.4 M ODES OF O PERATION ..................................................................................................... 18
2 FRONT PANEL CONTROLS .............................................................................................. 19
3 FUNCTIONS AND FACILITIES ........................................................................................... 20
3.1 D ISPLAY AND I CONS .......................................................................................................... 20
3.2 S WITCH O N /S WITCH O FF .................................................................................................. 21
3.3 V OLUME A DJUSTMENT ...................................................................................................... 21
3.4 S ELECTING A Z ONE ........................................................................................................... 21
3.5 S ELECTING A C HANNEL ..................................................................................................... 22
3.6 M AKING A C ALL (T RANSMITTING ) ...................................................................................... 22
3.7 R ECEIVING ....................................................................................................................... 23
3.8 E MERGENCY A LARM ......................................................................................................... 23
3.8.1 Receiving Emergency Calls.................................................................................... 23
3.8.2 Making an Emergency Call .................................................................................... 23
3.9 S CAN F UNCTIONS ............................................................................................................. 23
3.9.1 Scan Screen .......................................................................................................... 24
4 MENU SYSTEM .................................................................................................................. 25
4.1 M ENU N AVIGATION ........................................................................................................... 25
5 MENU SCREENS................................................................................................................ 27
5.1 C HANNEL M ENU ............................................................................................................... 27
5.2 Z ONE M ENU ..................................................................................................................... 27
5.3 S ETUP M ENU .................................................................................................................... 28
5.4 U SER O PTIONS M ENU ....................................................................................................... 28
5.5 M UTE A DJUST M ENU ........................................................................................................ 29
5.6 C ONTACT M ENU ............................................................................................................... 29

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 5 CONTENTS
5.7 R ADIO I NFORMATION ......................................................................................................... 30
5.8 RSSI M ENU ...................................................................................................................... 30
5.9 C ALL L OG ........................................................................................................................ 31
5.10 S CAN M ENU ..................................................................................................................... 31
5.11 C ONTRAST M ENU ............................................................................................................. 31
5.12 A LERT V OLUME M ENU ...................................................................................................... 32
5.13 S PEAKER V OLUME M ENU .................................................................................................. 32
5.14 K EY B EEPS ...................................................................................................................... 33
5.15 B ACKLIGHT ...................................................................................................................... 33
5.16 B RIGHTNESS M ENU ........................................................................................................... 34
6 SPECIAL FUNCTION BUTTONS........................................................................................ 35
6.1 C HANNEL U P A ND D OWN .................................................................................................. 35
6.2 Z ONE U P AND D OWN ......................................................................................................... 35
6.3 S CAN O N /O FF .................................................................................................................. 35
6.4 S KIP ................................................................................................................................. 35
6.5 T ALK A ROUND O N /O FF ..................................................................................................... 35
6.6 L OW P OWER .................................................................................................................... 35
6.7 C O T O C HANNEL 1, 2, 3 OR 4 ............................................................................................ 35
6.8 M ENU ............................................................................................................................... 35
6.9 Z ONE , C HANNEL , C ONTACT AND M UTE .............................................................................. 35
6.10 R ESET .............................................................................................................................. 36
6.11 S PEAKER M UTE ................................................................................................................ 36
6.12 D IGITAL O UTPUT ............................................................................................................... 36
6.13 U NDEFINED ...................................................................................................................... 36
7 TROUBLESHOOTING ........................................................................................................ 37
8 OPTIONS AND ACCESSORIES ......................................................................................... 38
APPENDICES
A1 ALERT TONES AND MESSAGES

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 6 CONTENTS
LIST OF FIGURES
Page
Figure 1. SDM610 Control Microphone. ....................................................................................... 19
Figure 2. Typical display sequence after Switch On. .................................................................... 21
Figure 3. Scan Screen information. .............................................................................................. 24
Figure 4. Menu Navigation. .......................................................................................................... 26
Figure 5. Channel Screen. ........................................................................................................... 27
Figure 6. Zone Menu.................................................................................................................... 27
Figure 7. Setup Menu. ................................................................................................................. 28
Figure 8. User Options Menu. ...................................................................................................... 28
Figure 9. Mute Adjust Screen....................................................................................................... 29
Figure 10. Contact Menu screen. ................................................................................................. 30
Figure 11. Radio Information Menu. ............................................................................................. 30
Figure 12. RSSI Menu.................................................................................................................. 30
Figure 14. Call Log Menu screen. ................................................................................................ 31
Figure 15. Scan Menu.................................................................................................................. 31
Figure 16. Contrast Menu screen................................................................................................. 32
Figure 17. Alert Volume Menu screen. ......................................................................................... 32
Figure 18. Speaker Volume Menu................................................................................................ 32
Figure 19. Key Beeps Menu screen. ............................................................................................ 33
Figure 20. Backlight Menu screen................................................................................................ 33
Figure 21. Brightness Menu screen.............................................................................................. 34
LIST OF TABLES
Page
Table 1. SDM610 – Control Functions. ........................................................................................ 19
Table 2. Icon Details. ................................................................................................................... 20
Table 3. SDM600 Mobile Radio – Options and Accessories. ....................................................... 38
Table A1. Alert Tones. ................................................................................................................. 39

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 7 WARNINGS
PERSONAL SAFETY
Safety Precautions
These Safety Precautions, Warnings and Cautions advise personnel of specific hazards which may
be encountered when using this equipment and that control measures may be required to prevent
injury to personnel, and damage to equipment and/or the environment.
Before using this equipment, personnel are to acquaint themselves with all risk assessments
relevant to the equipment and area of use. They must then comply with the control measures
detailed in those risk assessments.
References covering safety regulations, health hazards and hazardous substances are detailed
under the WARNINGS section below. These are referred to in this user manual when they are
encountered.
General Precautions
Do NOT operate your portable radio, without a hands-free kit, whilst driving a vehicle.
Do NOT operate your radio in an explosive atmosphere – unless the radio’s level of IECEx
approval is approved for use in that atmosphere.
Obey the ‘Turn Off Two-way Radios’ signs where these are posted, e.g. on a petrol station
forecourt.
Do NOT touch the antenna while the radio is transmitting.
Do NOT dispose of batteries in a fire.
Do NOT operate the radio if the antenna has become disconnected or damaged.
Only recharge batteries in an approved battery charger.
Hazardous Substances
Before using any hazardous substance or material, the user must be conversant with the safety
precautions and first aid instructions:
•On the label of the container in which it was supplied.
•On the material Safety Data Sheet.
•In any local Safety Orders and Regulations.
WARNINGS
Radio Frequency Radiation
WARNING
RADIO FREQUENCY RADIATION. A RADIO FREQUENCY (RF)
RADIATION HAZARD EXISTS IN THIS EQUIPMENT. TO AVOID RF
INJURY, DO NOT TOUCH THE ANTENNA WHEN THE TRANSMITTER IS
IN USE. DO NOT OPERATE TRANSMITTER WITH ANTENNA
DISCONNECTED.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 8 WARNINGS
Dangerous Voltages
Dangerous voltages exist in this equipment, for the appropriate Safety precautions, refer to the
relevant Electrical Safety Regulations appropriate to the country of operation.
WARNING
DANGEROUS VOLTAGES. DANGEROUS VOLTAGES EXIST IN ALL THE
BATTERY CHARGERS USED WITH THIS RADIO. FOR THE
APPROPRIATE SAFETY PRECAUTIONS REFER TO THE RELEVANT
ELECTRICAL SAFETY REGULATIONS APPROPRIATE TO THE
COUNTRY OF OPERATION.
Hints For Using The Radio
When transmitting, hold the radio a few centimetres from your mouth and speak across it, rather
than into it.
Keep the length of your conversation to a minimum to conserve battery life and replace the
microphone on its cradle after use.
When it is possible to move location, avoid making calls from known poor signal-strength areas
such as the radio systems fringe areas (limit of range) or from screened or shadowed areas, e.g.
an underground car park or underpass.
To avoid unnecessary drain on the vehicle battery, keep the engine running when using the radio
for extensive periods of time.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 9 RF ENERGY COMPLIANCE
COMPLIANCE WITH RF ENERGY EXPOSURE GUIDELINES
(UNITED STATES AND CANADA)
RF E NERGY E XPOSURE A WARENESS AND C ONTROL I NFORMATION AND
O PERATIONAL I NSTRUCTIONS FOR FCC O CCUPATIONAL U SE R EQUIREMENTS
Before using your Simoco mobile two-way radio, read this important RF energy awareness and
control information and operational instructions to ensure compliance with the Federal
Communications Commission’s (FCCs) RF exposure guidelines.
NOTICE.
This radio is intended for use in Occupational/Controlled conditions in a mobile application
where users have full knowledge of their exposure and can exercise control over their
exposure to meet occupational limits in FCC/ICNIRP and International Standards.. This
radio device is NOT authorised for general population consumer use.
This two-way radio uses electromagnetic energy in the Radio Frequency (RF) spectrum to provide
communications between two or more users over a distance. It uses RF energy or radio waves to
send and receive calls. RF energy is one form of electromagnetic energy. Other forms include,
but are not limited to, electric power, sunlight and x-rays. RF energy, however, should not be
confused with these other forms of electromagnetic energy, which, when used improperly, can
cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic
material.
Experts in science, engineering, medicine, health and industry work with organizations to develop
standards for exposure to RF energy. These standards provide recommended levels of RF
exposure for both workers and the general public. These recommended RF exposure levels
include substantial margins of protection. All Simoco two-way radios are designed, manufactured
and tested to ensure they meet government established RF exposure levels. In addition,
manufacturers also recommend specific operating instructions to users of two-way radios. These
instructions are important because they inform users about RF energy exposure and provide
simple procedures on how to control it. Please refer to the following websites for more information
on what RF energy exposure is and how to control your exposure to assure compliance with
established RF exposure limits.
http://transition.fcc.gov/oet/rfsafety/rf-faqs.html
http://www.osha.gov/SLTC/radiofrequencyradiation/
Federal Communications Commission Regulations
The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile
two-way radios before they can be marketed in the United States (US). When two-way radios are
used as a consequence of employment, the FCC requires users to be fully aware of and able to
control their exposure to meet occupational requirements. Simoco two-way radios have an
exposure awareness label attached to the equipment directing users to specific awareness
information. Do not remove this exposure awareness label from the device. Additionally, your
Simoco user manual or separate safety booklet includes information and operating instructions
required to control your RF exposure and to satisfy compliance regulations.
Compliance with RF Exposure Standards
Simoco two-way radios are designed and tested to comply with a number of national and
international standards and guidelines (listed below) for human exposure to RF electromagnetic
energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for
Occupational/Controlled RF exposure environments at operating duty factors of up to 50% talk
50% listen and is authorised by the FCC for occupational use. In terms of measuring RF energy

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 10 RF ENERGY COMPLIANCE
for compliance with the FCC exposure guidelines, your radio radiates measurable RF energy only
while it is transmitting (during talking), not when it is receiving (listening) or in standby mode.
Your Simoco two-way radio complies with the following RF energy exposure standards and
guidelines:
•United States Federal Communications Commission, Code of Federal Regulations; 47CFR
part 2 sub-part J.
•American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers
(IEEE) C95.1-1992.
•Australian Communications Authority Radio Communications Standard et seq.
•Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition.
•Industry Canada RSS-102.
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control exposure to yourself and others and ensure compliance with the
Occupational/Controlled environment exposure limits always adhere to the following procedures.
Guidelines:
•User awareness instructions should accompany the device when transferred to other users.
•Do not use this device if the operational requirements described herein are not met.
Instructions:
•Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the
Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of
the time, or less, is important because this radio generates measurable RF energy exposure
only when transmitting (in terms of measuring for standards compliance).
•Transmit only when people outside the vehicle are at least the recommended minimum
lateral distance away, as shown in Tables 1 and 2, from a properly installed according to
installation instructions, externally-mounted antenna.
Notes:
(i). Table 1(a) lists the recommended minimum lateral distance for bystanders in an
uncontrolled environment from the transmitting antenna for the SDM600AC (150 MHz –
174 MHz) mobile rated power (25 Watts) installed in a vehicle.
(ii). Table 1(b) lists the recommended minimum lateral distance for
occupational/controlled use.
(iii). Table 2(a) lists the recommended minimum lateral distance for bystanders in an
uncontrolled environment from the transmitting antenna for the SDM600TU and
SDM600UW (406.1 MHz – 512 MHz) mobile rated power (25 Watts) installed in a vehicle.
(iv). Table 2(b) lists the recommended minimum lateral distance for
occupational/controlled use.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 11 RF ENERGY COMPLIANCE
Table 1(a). Rated Power and Recommended Lateral Distance for General Population
Uncontrolled Exposure for SDM600AC (150 MHz to 174 MHz).
Rated Power of Vehicle- installed
Mobile Two-way Radio
Recommended Minimum Lateral
Distance from Transmitting Antenna
25 Watts with λ/4 dipole (2.14 dBi gain) 90 cm (35.5 inches)
Table 1(b). Rated Power and Recommended Lateral Distance for Occupational/Controlled
Exposure for SDM600AC (150 MHz to 174 MHz).
Rated Power of Vehicle-installed
Mobile Two-way Radio
Recommended Minimum Lateral
Distance from Transmitting Antenna
25 Watts with λ/4 dipole (2.14 dBi gain) 40 cm (15.75 inches)
Table 2(a). Rated Power and Recommended Lateral Distance for General Population
Uncontrolled Exposure for SDM600TU and SDM600UW (406.1 MHz to
512 MHz).
Rated Power of Vehicle- installed
Mobile Two-way Radio
Recommended Minimum Lateral
Distance from Transmitting Antenna
25 Watts with λ/4 dipole (2.14 dBi gain) 75 cm (29.5 inches)
Table 2(b). Rated Power and Recommended Lateral Distance for Occupational/Controlled
Exposure for SDM600TU and SDM600UW (406.1 MHz to 480 MHz).
Rated Power of Vehicle- installed
Mobile Two-way Radio
Recommended Minimum Lateral
Distance from Transmitting Antenna
25 Watts with λ/4 dipole (2.14 dBi gain) 34 cm (13.5 inches)
Vehicle Installation Instructions
The antenna(s) used for the SDM600 series of mobile two-way radios must be installed to provide
a separation distance of at least 90 cm (35.5 inches) from all persons for SDM600AC (150 MHz -
174 MHz), 75 cm (29.5 inches) for SDM600TU and SDM600UW (406.1 MHz – 512 MHz). The
gain of the antenna(s) may not be greater than 0 dBd (2.14 dBi).
If the required separation distance extends beyond the physical boundary of the vehicle, the
antenna must be installed on the centre of the roof ONLY and must be installed in a vehicle having
the following characteristics in order to prevent bystanders from being exposed to levels exceeding
the limits set for General Population/Uncontrolled exposure environment:
•All passengers must be sitting under a solid metal roof.
•The rooftop width must be at least 180 cm (71 inches) for SDM9000AC (150 MHz –
174 MHz), 150 cm (59 inches) for SDM600TU and SDM600UW (406.1 MHz – 512 MHz).

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 12 RF ENERGY COMPLIANCE
Mobile Antenna
•Install the antenna at the centre of the roof or the centre of the trunk deck, taking into
account the bystander exposure conditions of backseat passengers and recommended
minimum lateral distances in Tables 1(a) and 2(a). These mobile antenna installation
guidelines are limited to metal body motor vehicles or vehicles with appropriate ground
planes.
•The antenna installation must additionally be in accordance with:
o The requirements of the antenna manufacturer/supplier.
o Instructions in the Radio Installation Manual, including minimum antenna cable lengths.
o The installation information of how to install the antenna to facilitate recommended
operating distances to all potentially exposed persons.
•Use only Simoco approved supplied antenna or Simoco approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage the radio and may
violate FCC regulations.
Approved Accessories
•This radio meets the FCC RF exposure guidelines when used with the Simoco accessories
supplied or designated for the product. Use of other accessories may not ensure compliance
with the FCCs RF exposure guidelines and may violate FCC regulations.
•To obtain a list of Simoco approved accessories please see the Simoco Group Departmental
contact details on the Support page and either contact the relevant Technical Support
Helpline or Customer Services, visit the following website, which lists approved accessories:
http://www.simocogroup.com
For additional information on exposure or other information, please see the Simoco Group
Departmental contact details on the Support page and contact the relevant Technical Support
Helpline or Customer Services.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 13 GENERAL NOTES
GENERAL NOTES
M ANUAL C OMPILATION
This manual provides detailed information on the Operating Instructions for the SDM610 Portable
Radio Transceiver including Introduction, Controls, Menu System, Menu Screens, Common
Functions & Facilities, Special Function Keys, Troubleshooting and Options.
Details of both “basic” and “optional units” have been included in this User Manual, therefore, some
material may not be relevant to every system. Configuration is dependent upon the specification
by the customer when the equipment was ordered and installed.
P AGINATION
This manual is divided into a number of sections, each section deals with one aspect of the
system.
Following initial issue, any page that has been amended or updated will also bear an updated
reference.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 14 SUPPORT
SIMOCO SUPPORT
C ONTACT I NFORMATION
At Simoco we welcome your comments, feedback and suggestions. Departmental contacts have
been provided for your quick reference below.
UK Customer Services
Email: [e-mail]
Tel: UK: 08717 411 050
International: [phone]
Fax: UK: 08717 411 049
International: [phone]
Sales
E-mail [e-mail]
Marketing
E-mail [e-mail]
Australian Customer Services
Email: [e-mail]
Tel: Within Australia: 1300 363 607
International: [phone]
US Customer Services
Email: [e-mail]
Tel: [phone]
T ECHNICAL S UPPORT
In order to streamline support requests and better serve our customers, at Simoco we utilize a
support ticket system. Every support request is assigned a unique ticket number, which customers
can use to track the progress and responses online. In order to use the support ticket system, a
valid email address is required.
A link to the online Support Centre Ticket Tracking system is provided below:
http://simocoradiosupport.com

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 15 SUPPORT
If you still require further technical assistance after raising a support ticket, please contact us via
the email addresses or via the Technical Support Helpline numbers overleaf.
Technical Support Email Addresses
Simoco EMEA: [email protected]
Simoco Australasia: [e-mail]
Simoco Americas: TBD.
Technical Support Helplines
Simoco EMEA: Tel: UK: 08717 411 040
International: [phone]
Simoco Australasia: Tel: Within Australia: 1300 363 607
International: [phone]

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 16 ABBREVIATIONS
ABBREVIATIONS
The following abbreviations are used through out this document. Whenever practicable, wherever
the abbreviation is first used the full meaning is given with the abbreviation in parenthesis, after
that only the abbreviation will be used.
LIST OF ABBREVIATIONS
Abbreviation Meaning
ANSI American National Standards Institute
CC Colour Code
CTCSS Continuous Tone Controlled Sub-audible Squelch
DCS Digital Coded Squelch
DMR Digital Mobile Radio
DSP Digital Signals Processor
FCC Federal Communications Commission
FM Frequency Modulation
FPP Field Personality Programmer
ICNIRP International Commission on Non-Ionizing Radiation Protection
ID Identification
IECEx International Electrotechnical Commission system for the certification to
standards for electrical equipment for Explosives atmospheres.
IEEE Institute of Electrical and Electronics Engineers
LCD Liquid Crystal Display
LED Light Emitting Diode
PTT Push (Press) To Talk
RF Radio Frequency
RSSI Received Signal Strength Indicator
Rx Receiver
SDM Simoco Digital Mobile
SMSG Short Message
TGID Talk Group Identification
Tx Transmitter
TXTMSG Text Message
US United States

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 17 ABBREVIATIONS
GLOSSARY OF TERMS
The table below contains a list of the common terms used through out this document and their
meanings.
Term Meaning
‘……’ Reference to a setting or feature (exactly as it is displayed) that may be
selected or enabled either directly or through a software application, e.g.
‘Menu’, ‘Control’, ‘Switch’.
Channel A logical combination of RF Frequency, Default Talk Group Indentity (TGID),
other channel associated parameters (CTCSS, scan etc)
CTCSS A sub-audio tone used for validating a received signal (also known as a PL
tone).
FPP Field Personality Programmer or Field Programmer. A Software Application
used for configuring the radio options and parameters.
Monitor Mode of Radio Receive. Any DMR signal regardless of Colour Code or TGID
will be heard.
Normal Mute Mode of Radio Receive. Only signals with matching Colour Code will be
heard.
Push To Talk The action or signal that causes the equipment to be placed into transmit
mode or to be keyed.
Radio Unit ID Unique identifier allocated to each radio (range: 0 – 16,000,000).
Selective Mode of Radio Receive. Only signals with matching Colour Code and TGID or
Unit ID will be heard.
Vote/voting The selection of the best received signal from a collection of signals presented
individually and simultaneously.
Zone A collection of channels (usually organised by functional group of users).

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 18 INTRODUCTION
1 INTRODUCTION
1.1 O VERVIEW
The SDM600 Series Radios are versatile Digital Signal Processor (DSP) controlled, two-way
mobile radios. The SDM600 Series is available in a number of frequency bands and versions for
specific applications. These Operating Instructions describe the operation of the DMR Tier II
Standard compliant Mobile Radio, consisting of an SDM600 Transceiver and SDM610 Control
Microphone.
The radio is software programmable and it can be customised to the operational requirements of
your particular fleet. Your Simoco representative can help in programming your radio facilities to
meet your present and future requirements.
1.2 C ONFIGURATION
The SDM610 Radio must be configured using the Field Personality Programmer (FPP) prior to
operation. The configuration process defines the radio channels, signalling and other settings so
that the radio will operate with your system.
1.3 I NSTALLATION
As the installation of your SDM600 Transceiver is a technical and possibly hazardous operation,
we recommend that it is installed and set up for use by your dealer or an authorised installer.
However, if you need information regarding the correct procedures for installation, please refer to
the SDM600 Series Installation Instructions [2] supplied with the radio.
1.4 M ODES OF O PERATION
The SDM610 Radio is capable of operation in Analogue FM and DMR modes.
Radio Channels are organised in groups of up to 250 per zone. Up to 40 zones may be defined.
Generally, zones can be programmed with channels belonging to common function groups.
A radio channel can be defined as either Analogue or DMR, and a Zone may contain a mix of
Analogue or DMR Channels.

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 19 CONTROLS
2 FRONT PANEL CONTROLS
The controls on the SDM610 Control Microphone are shown below in Figure 1.
Figure 1. SDM610 Control Microphone.
The functions of each of the controls are detailed in below Table 1.
Table 1. SDM610 – Control Functions.
SDM610 Key Label Function
On/Off
To turn the radio On or Off, push and hold the On/Off button for
about 1 second.
PTT
Push-To-Talk. Hold the microphone about 10 cm from the
mouth. Press and hold the PTT switch and speak. Release to
listen.
Volume Up/Down Press and hold either the Up or Down buttons to increase or
decrease the volume as required.
Function Key F1 M Programmable Function key. Default – Change Menu.
Used to move between Menu screens.
Function Key F2 Programmable Function key.
Default – Emergency Alarm.
Function Key F3 Programmable Function key. Default – Menu Return.
Used to return to the Main Menu screen.
Function Key F4 S Programmable Function key. Default – Scan On/Off or Select.
Used to select an item from a list, or activate Scanning.
Scroll Up ▲Programmable Function key. Used to scroll up through a list
within a Menu. Default – Channel Up.
Scroll Down ▼Programmable Function key. Used to scr
oll down through a list
within a Menu. Default – Channel Down.
The four programmable buttons, F1 to F4, can be programmed, using the FPP Programmer, to
perform different functions. If the default settings, described above, are changed, alternative
means should be provided to perform their original functions.
Volume Down
Volume Up
Microphone
PTT
Display
On/Off
Scroll Up
Scroll Down
F3 - Return to Menu
F1 - Change Menu
F4 - Scan On/Off
or Select
F2 - Alarm

SDM610 – USER MANUAL TNM-U-E-0109
Oct 13 (Iss. 1.3) Page 20 FUNCTIONS & FACILITIES
Searching
Invalid
Signal
Valid Signal
Icons
Scanning
Stored Call
3 FUNCTIONS AND FACILITIES
3.1 D ISPLAY AND I CONS
The display shows text information relevant to the selected Menu Screen.
The Name field (e.g. Ch73) shows the selected entry from the current screen (e.g. from the
Channel List).
Several Icons can be individually displayed as shown below in Table 2.
Table 2. Icon Details.
Icon Description
Valid signal + CTCSS is being received.
Audio can be heard from the loudspeaker.
Invalid signal. Carrier with incorrect CTCSS is being received.
This symbol indicates that the radio is transmitting.
The rotating icon indicates that the radio is searching for a channel, (e.g. while
Voting). The symbol disappears when stopped on a channel.
Scanning indicator shows that the radio is searching the channels in the Scan
Group.
When not transmitting or receiving, flashes to indicate stored calls.
The ‘M’ button is used to access the available Menu options. Where menu selection is not
required, this button can be reprogrammed to perform other functions in this screen.
The ▲▼buttons scroll up and down through the available selections within a Menu Screen.
The F1, F2, F3 and F4 buttons are programmable function buttons, in this screen.