Sirius Satellite Radio SUM Series User manual

INSTALLATION
INSTRUCTIONS
CARE AND USE MANUAL FOR:
WALL RANGE HOODS
Models covered by this instructions:
SUM1 - SUM6
*** BEFORE INSTALLATION ***
ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED
DURING SHIPPING
*** SHIPPING DAMAGE ***
MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

WARNING
Thank you for purchasing a Sirius Range Hood.
Please read all the instructions in this manual before
installing the appliance.
Save these instructions for future reference.
Only use this appliance as an exhaust ventilation system for the removal of
cooking vapors. DO NOT use to expel ammable substances or any other
materials or vapors.
The installation procedures in this manual are intended for qualied instal-
lers, service technicians or persons with similar qualied background.
DO NOT attempt to install this appliance yourself.
Ensure that electrical power is turned o at source before commencing in-
stallation. All electrical wiring must be properly installed, insulated and
grounded and conform to all applicable codes and standards.
Make sure all existing duct work is clean of grease build up, or duct work
should be replaced, if necessary, to avoid the possibility of a grease re.
Check all joints on ductwork to ensure proper connection and all joints
should be properly taped. Be careful when cutting through ceilings or walls
not to damage any hidden pipes or electrical wiring. Ensure your kitchen has
sucient air return vents to replace the exhausted air.
Fan ducts should always be vented to the outside of your home and never
into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel
for ducting. The exhaust point of the blower requires a 6” round connec-
tion.
2

TABLE OF CONTENTS
3
Warnings 4
Useful warnings 4
Warnings 4
SUM1 5
Types of installation 5
Installation of the appliance 6
Connection of the pipes 6
Electrical connection of the hood SEM1 6
SUM6 7
Warning 7
Installation 7
Connection of the pipes 8
Electrical connection to the hood 8
Installation of the external carter 8
WARRANTY 12

4
Warnings!
The air outlet of the appliance must not be connected to a ue which is used for
exhausting
other fumes from appliances, such as a central heating, boilers etc..
For the external exhausting of the fumes, comply with the regulations in force.
Ventilate the room suitably according to the laws in force when the appliance is wor-
king together with gas, oil or coal burning appliances, at the same time.
The motor of the peripheral exhausting group is powered by the cooker-hood placed
in the kitchen.
Before connecting the cooker hood to the mains supply, make sure that the voltage
indicated in the rating plate corresponds to the mains voltage in the home.
Before carrying out any sort of maintenance or cleaning operation, make sure that
the appliance is disconnected from the electrical mains.
An appropriate maintenance ensures a good working and a good performance in the
long run.
Useful warnings:
- Use an air outlet pipe with a maximum length not higher than 5 meters.
- Limit the number of bends in the exhausting pipe as every bend reduces the per-
formance up to one linear meter. (If you use 2 90° bends, than the length of the pipe
has not to be higher than 3 meters).
- The material for the pipe has to be approved by an authorized company.
- It is important to avoid changes in the diameter (we recommend a diameter of
150mm).
- Read carefully the manual of instructions and installation of the unit.
- Sirius will not be responsible for problems of capacity and/ or noise level due to the
missed respect of the warnings included in the manual of instructions.
- SEM6 are equipped with a 200mm diameter hole for the exhausting pipe. If the
unit that has to be connected to the remote fan is already equipped with a 200mm
diameter hole, the nit is recommended to use a pipe with the same diameter in order
to get good performances. Otherwise, if the unit is equipped with a 150mm diame-
ter hole, than it is recommended to use the joint (from 200mm to 150mm), already
supplied with the unit.
The electric box cable should not be cut or joined together with other cables, since
it could compromise the proper working and the safety conditions of the appliance.
Furthermore, this will invalidate the manufacturer’s warranty coverage.
Warnings!
The SEM6 suction centrals can be connected to any other products from the same
manufacturer if they are equipped with the External Motor version.
The manufacturer cannot be held responsible for damages caused by a dierent use.

5
SUM1
The appliance is designed to exhaust fumes and odours very silently and in the best
way. It must be installed in the house and connected to the cooker-hood, which is in
the kitchen g.1.
Types of installation: to make the installation easy, the appliance can be xed on
the wall, on the ceiling or on the oor in a horizontal position g.2 or vertically g.
3 to the xing level.
Note: in the vertical xing, the brackets supplied can be used only on the longest
side g. 4.

6
Installation of the appliance: after deciding the position and the type of installation,
insert the anti-vibration rubber caps in the holes of the brackets supplied g. 5C.
The rubber caps must be put on the sides which are in contact with the wall.
Put the brackets (g. 5A) on the remote tted extraction motor by matching its holes
with those of the brackets. Fix with the screws supplied (g. 5B).
Put the group on the point previously chosen for the installation and mark the points
on the wall where the holes must be drilled. Insert the dowels supplied in the holes
(g. 4A). Put the remote tted extraction motor on the wall by matching the holes of
the brackets with the plastic dowels. Screw with the screws sup- plied (g. 4B).
Connection of the pipes: the appliance is endowed with an entrance and an outlet to
connect the pipes. Before connecting the exhaust pipes, check the direction of the air
showed on the external label (g. 6). Connect the pipes and x them with appropriate
metal clamps (exhaust pipes and metal clamps have to be supplied by the installer).
The pipe (g. 6A) must be con- nected with the cooker-hood placed in the kitchen,
and the pipe (g. 6B) must be directed outside the building.
Electrical connection of the hood SEM1: the appliance is equipped with a 7m elec-
trical cable with a six- pin connection at one end. Insert it into the hood’s connection
(External Motor version).

7
SUM6
Warning!
The remote tted exhausting group (external motor) is built in class I plate, therefore
it needs the earth connection.
The appliance was designed to exhaust odors and vapors in the best way. The ap-
pliance is to be installed on the outside wall of the house and connected to the
cooker-hood which is in the kitchen (g. 1).
Installation:
the mounting of the appliance is to be made by qualied technicians. Using the ap-
propriate drilling jig.
(g. 2) drill all the holes marked on it into the external wall, by paying attention not
to damage water pipes or power lines. The holes on the wall are to be drilled with a
8 mm. bit.
Insert, step by step, the following parts in the holes drilled:
- the corresponding plastic dowels supplied
- the two telescopic pipes in the hole of 200 mm.
- the plastic pipe of 40 mm. diameter.

Before leaning the appliance against the wall, please remove the stainless steel carter
using the 8 perimetrical screws (g. 3),
then insert the supply cord in the plastic pipe. Fix the appliance without the stain-
less steel external body, which was previously removed from the motor block, by
matching the holes of the motor block with the holes on the wall. Tighten with the
screws supplied.
Connection of the pipes:
the appliance is endowed with an air entrance to be connected with the telescopic
pipes and an air outlet. After xing the appliance on the external wall, connect the
two telescopic pipes (g. C), which are placed inside the wall, with the cooker-hood
through the exible pipes.
The xing operations have to be carried out by using suitable metallic tools (pipes
and tools have to be supplied by the installers).
Electrical connection to the hood:
the unit is supplied with a pipe 7 meters long. After having let the cable pass throu-
gh the plastic pipe (Fig. e) placed in the wall (g. d), placed it closed to the unit and
connect the 6 poles connector (Fig. e).
In order to avoid water inltrations, please apply silicone on the product perimeter,
close to the wall.
Installation of the external carter:
mount the aesthetic carter making sure that the grill will match with the block motor
air outlet.
8

9

10