Sirona c8+ turn User manual

New as of: 10.2014
English
C8+/ C8+Turn
Installation Requirements

New as of: 10.2014
General information Sirona Dental Systems GmbH
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
2D3417.021.04.11.02
Changes since the last version (09/2009):
Chapter or section, page
Does not apply to the following products:
C8+Solo, C8+Stand-Alone, C8+Side delivery,
C8+Rear delivery
About this document
This document describes the installation requirements for
the C8+/C8
+Turn/C8 +Turn treatment centers.
The following sets of Installation Instructions describe the
subsequent installation procedure:
• REF 59 42 912 (C8+)
• REF 59 78 197 (C8+Tu r n )
You will also need the following drilling template in order to
fasten the treatment center securely to the floor:
• REF 59 66 911 (C8+,C8
+Tu r n )
General information

Sirona Dental Systems GmbH Table of contents
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
D3417.021.04.11.02 3
English
1Preparations....................................................................................................................... 5
1.1 Safety........................................................................................................... 6
1.2 Media quality................................................................................................ 7
1.3 Supply lines in the termination panel ........................................................... 8
1.4 Underfloor installation of SIVISION connections ......................................... 11
1.5 Mounting plates C8+(not for C8+Turn) ....................................................... 12
1.6 Demonstration chair plate C8+Turn ............................................................ 13
2Dimensions, technical data ............................................................................................ 15
2.1 C8+1:20....................................................................................................... 16
2.2 C8+Cart 1:20............................................................................................... 21
2.3 C8+: Technical data ..................................................................................... 23
2.4 C8+Turn 1:20 .............................................................................................. 24
2.5 C8+Turn Cart 1:20 ...................................................................................... 31
2.6 C8+Turn: Technical data ............................................................................. 33
3Electromagnetic compatibility ....................................................................................... 35
3.1 Accessories ................................................................................................. 36
3.2 Electromagnetic emission............................................................................ 37
3.3 Immunity to interference .............................................................................. 38
3.4 Working clearances ..................................................................................... 40
Table of contents

C8+/C8
+Turn
60 28 000 D3417
D3417.021.04.11.02 5
1Preparations
1.1 Safety .................................................................................................................................... 6
1.2 Media quality ......................................................................................................................... 7
1.3 Supply lines in the termination panel ..................................................................................... 8
1.4 Underfloor installation of SIVISION connections ................................................................... 11
1.5 Mounting plates C8+(not for C8+Turn) ................................................................................. 12
1.6 Demonstration chair plate C8+Turn ...................................................................................... 13

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
6D3417.021.04.11.02
ATTENTION
It is essential that you comply with the warning and safety
information contained in the Installationsvoraussetzungen.
All such information is highlighted by the signal words
NOTE, CAUTION or WARNING.
ATTENTION
The unit may only be operated by properly trained person-
nel. On-site installation must be performed in accordance
with our specifications.
In our capacity as a manufacturer of medical electrical
equipment, we only consider ourselves to be responsible for
the safety characteristics of the unit if we perform mainte-
nance and repair work on it ourselves or if this is performed
by centers that we have expressly authorized to do so; and if
defective components are replaced with original spare
parts.
When this work is carried out, we recommend that you ask
those responsible for the work to provide a certificate indi-
cating the nature and scope of the work, including details of
changes to rated data or the working area where applicable.
This certificate should also be signed and dated, and should
show information about the relevant company.
ATTENTION
By law, any changes to this unit which may compromise the
safety of operators, patients or third parties are not permis-
sible.
For reasons of product safety, this product may only be op-
erated with original Sirona accessories or accessories from
third parties approved by Sirona. The user assumes the risk
of using non-approved accessories.
If any devices not approved by Sirona are connected, they
must comply with the applicable standards, e.g.:
– IEC 60950 for information technology equipment
(e.g. PCs) and
– IEC 60601-1 for medical equipment.
The monitor used at the treatment center must meet the re-
quirements of IEC 60950. The loudspeaker port of the mon-
itor may only be connected to a device that complies with
IEC 60950 (e.g. a PC) or IEC 60601-1. Under no circum-
stances may it be connected to a stereo system, for exam-
ple.
If a system is being assembled during installation, the re-
quirements of IEC 60601-1 (3rd edition) must be adhered
to. The person assembling the system assumes responsi-
bility for ensuring that it conforms to Directive 93/42/EEC.
ATTENTION
The floor must be flat and level (DIN 18 202). A mounting
plate must be used for uneven floors (see Section 1.5,
"Mounting plates C8+(not for C8+Turn)" on page 12).
ATTENTION
The floor must have a minimum loading capacity of 0.5N/
cm².
ATTENTION
Wireless phone interference with medical electrical equip-
ment:
To ensure safe operation of medical electrical equipment,
the use of mobile wireless phones in practice or hospital en-
vironments is prohibited.
ATTENTION
Electromagnetic compatibility: The unit should not be op-
erated in the immediate vicinity of other devices. If this
proves to be unavoidable, the unit should be monitored to
ensure that it is operating properly.
1.1 Safety

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
D3417.021.04.11.02 7
English
,
Water quality
Lime deposits and corrosion residues in tap water can lead
to the following malfunctions:
• Premature clogging of the filters in the unit
• Rapid clogging of the fine water paths and jets in the
treatment instruments
For these reasons, the following points must be observed:
• Permitted water pressure: 2.5 bar (36.25 psi) to 6 bar
(87 psi)
• Permitted minimum flow volume: 3 l/min
• For water hardness (total hardness) of 2.2 mmol/l (=
12° dH ), install water softeners.
Set the blend hardness to 1.4 mmol/l (= 8° dH).
• Install a conventional fine filter; fineness: > 80 µm (0.08
mm).
• Installation must be performed in compliance with the
recommendations of the national installation require-
ments (e.g. EN 1717/DIN 1988).
• The water quality must comply with the national re-
quirements for drinking water.
• The connection must be made to cold water.
• When laying the water pipe to the treatment center,
comply with the following instructions to reduce the
quantity of micro-organisms in the feed pipe:
– Avoid long stub lines to the treatment center.
– Carry out the installation so that, where possible,
other main consumers (such as the sink) are fed
from the same line downstream of the treatment
center connection.
– Avoid laying the supply line parallel to hot water
pipes.
• Observe EN 1717 for the protection of public drinking
water.
Provided a disinfection system is also installed, the
treatment center fulfills the requirements of EN 1717
and of the DVGW (German Technical and Scientific As-
sociation for Gas and Water). It can be connected di-
rectly to the public drinking water system.
Air quality
The air for driving the turbines, for cooling the drives and for
the cooling spray must be free from oil, dry and hygienically
faultless.
Suction pipe
Install steam trap K.
With a vacuum of pu >0.18 bar back pressure, the treat-
ment center must be retrofitted with the "Vacuum limiter"
retrofit kit
(REF 59 68 826).
1.2 Media quality
N
>80 µm
Air
Suction machine
oil-free
Cold water
Dilution hardness
(drinking water quality)
1 bar = 100 kPa = 14.5 psi

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
8D3417.021.04.11.02
1.3 Supply lines in the termination panel
5
3
6
6
67
Center base plate
opening to floor
1
2
4
9
1 3/8“
min.
500mm
20”
7, 6
max.
60mm
2 3/8”
3 4 5
max.
5mm
3/16”
max.
5mm
3/16”
3/8”
12
10 x 1mm 10 x 1mm
3/8”x 1/32“
3/8”x 1/32“
1 3/8“
Foot end
36.5mm
50 mm
36.5mm

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
D3417.021.04.11.02 9
English
• Observe the national regulations for electrical installa-
tions (e.g. VDE 0100, VDE 0100, Part 710).
• Comply with the national regulations for water supply
installations (e.g. EN 1717, DIN 1988) and sewage in-
stallations (e.g. EN 12056-1).
• For the suction pipe, observe the instructions in the
Suction Machine Installation Instructions.
• For fastening the pipe ends in the installation field, we
recommend using an installation template. They can
be ordered from Sirona under REF 33 15 830.
If necessary, you can also prepare the template your-
self based on the above sketch (not true to scale!).
Supply lines in the termination panel
Table 1: Supply lines
Item Description
1Water inlet pipe 10x1 mm,
corner valve outlet 3/8"
2Compressed air inlet pipe 10x1mm, corner
valve outlet 3/8"
3Suction pipe DN40 HT-PP DIN 19560 (polypro-
pylene, inner diameter 36.5mm!)
4Water drain DN40 HT-PP DIN 19560 (polypro-
pylene, inner diameter 36.5mm!)
5Installation pipe, DN40 HT-PP DIN 19560
(polypropylene, 40mm!)
6Suction machine control cable ( )and call
cables ( ) 3x1.5mm2
7Power cable 3x1.5mm2
Fuse: 16A slow-blow
Recommended: Type B automatic circuit
breaker
8 Not applicable
9 Installation pipe (or corresponding flat duct) for
additional requirement e.g. practice network
connecting cable
,

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
10 D3417.021.04.11.02
Supply above the floor, "above-floor installation"
The supply pipe ends, corner valves and cables must be
routed as shown above.
The retrofit kit for above-floor installation (REF 33 17 265)
is required for connection.
ATTENTION
For cleaning, flush the air and water pipes thoroughly (metal
chips!).
Supply through the floor, "underfloor installation"
1. The top edges of the corner valves for air and water
must not protrude more than 60mm above the upper
surface of the finished floor.
2. The suction and drain pipes must be flush with the up-
per surface of the floor (a deviation of +5mm is permis-
sible).
Internal diameter for both pipes: 36.5mm.
3. The electrical cables must protrude at least 500mm.
Supply lines in the termination panel
>500mm
<5mm
<60mm
>20“
3/8“
<3/16“
<2 3/8“
Ø 36,5 mm
10x1 mm
3/8” x 1/32”
DN 40
>5
00mm
200mm
250mm
> 20’’
8’’
10’’
Ø 36,6mm
3/8“
20
Ø36,5 mm
Installation template

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
D3417.021.04.11.02 11
English
Important information for the installer
Depending on the prevailing local conditions, the existing
cable set can be installed in the cable duct of an underfloor
installation by an installer prior to the installation of the
treatment center. In this case, please observe the following:
Proceed with extreme care when running the cables. Par-
ticularly cables L15 and L38 are very sensitive, and must
never be kinked or twisted. The cables must not overlap or
cross one another.
RS232 (L37) and the XGA cable (L38) are not yet cut to
length and terminated on the PC side. It would be impossi-
ble to pull the cables through when installing them under
floor level if a sub D connector were already connected.
These cables should always be pulled.
Free length Aof cables at the treatment center end:
Length A= 600mm
If S video cable L15 is equipped with both a female and a
male connector, make sure that the female connector
(socket) points to the connection box of the treatment cen-
ter.
1. Bend the wire at the front end of cables L37 and L38 to
form a hook.
2. Pull cables L15,L37, and L38 as well as the audio ca-
ble and the protective earth conductor for the treatment
center through the cable duct to the location of the SIV-
ISION PC.
Save the accessory parts for final installation!
1.4 Underfloor installation of SIVISION connections
2.
1.
A
L15, L37, L38, audio
Protective earth conductor
SIVISION

1 Preparations Sirona Dental Systems GmbH
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
12 D3417.021.04.11.02
1.5 Mounting plates C8+(not for C8+Turn)
Mounting plate
Demonstration chair plate
REF 58 26 511
REF 47 08 074
For especially uneven floor conditions, a steel mounting
plate is available to compensate for the irregularities of
the floor (REF 58 26 511).
For floors which do not permit permanent connection of the unit (e.g.
demo operation at a fair), installation on a steel demonstration chair
plate is possible (REF 47 08 074).

Sirona Dental Systems GmbH 1 Preparations
Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
D3417.021.04.11.02 13
English
1.6 Demonstration chair plate C8+Turn
Demonstration chair plate
For floors which do not permit permanent connection
of the unit (e.g. demo operation at a fair), installation
on a steel demonstration chair plate is possible
(REF 59 46 269).
REF 59 46 269
C8+Turn

C8+/C8
+Turn
60 28 000 D3417
D3417.021.04.11.02 15
2Dimensions, technical data
2.1 C8+1:20 ................................................................................................................................. 16
2.2 C8+Cart 1:20 ......................................................................................................................... 21
2.3 C8+: Technical data................................................................................................................ 23
2.4 C8+Turn 1:20......................................................................................................................... 24
2.5 C8+Turn Cart 1:20 ................................................................................................................. 31
2.6 C8+Turn: Technical data........................................................................................................ 33

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
16 D3417.021.04.11.02
Recommended distances from cabinet or wall
2.1 C8+1:20
1700
67”
1300
51 3/16”
2500
98 7/16”
250
9 7/8”
!
!
250
9 7/8”
Hazard warning:
The lamp installed here and the dentist
element have a swivel range which ex-
ceeds the specified distances!
Center of floor opening

Sirona Dental Systems GmbH 2 Dimensions, technical data
Installation Requirements C8+/C8
+Tu r n 2.1 C8+1:20
60 28 000 D3417
D3417.021.04.11.02 17
English
With long support arm for the dentist element
C8+1:20
* max. 755 29 3/4”
min. 395 15 1/2"
1212
47 3/4”
Standard upholstery
*max.: backrest and chair at highest setting
min.: backrest and chair at lowest setting
45
1 3/4”
90
3 1/2”
1950
76 3/4”
Height of the lamp with
SIVISION on the swivel
arm or lamp support
tube
1875
73 3/4”
Height of the lamp
without SIVISION or
SIVISION on the tray
45°
65°
10°
max. 1230 48 3/8”
min. 760 29 7/8”
SIROLUXLEDview

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
18 D3417.021.04.11.02
C8+1:20
1540
60 5/8”
860
33 7/8”
1210
47 1/2”
310
12 1/4”
max. 380 +15
15“ +5/8”
2070 +50***
81 1/2” +2“ ***
*** Depending on the
chair height
45
1 3/4”
78
3”
459
18”
430 +15
17“ +5/8”
180
7”
90°
90° 90°
60°
750
29 1/2”
770
30 3/8”
250
9 7/8”

Sirona Dental Systems GmbH 2 Dimensions, technical data
Installation Requirements C8+/C8
+Tu r n 2.1 C8+1:20
60 28 000 D3417
D3417.021.04.11.02 19
English
With short support arm for the dentist element
C8+1:20
* max. 755 29 3/4”
min. 395 15 1/2"
1212
47 3/4”
Standard upholstery
*max.: backrest and chair at highest setting
min.: backrest and chair at lowest setting
45
1 3/4”
90
3 1/2”
1950
76 3/4”
Height of the lamp with
SIVISION on the swivel
arm or lamp support
tube
1875
73 3/4”
Height of the lamp
without SIVISION or
SIVISION on the tray
45°
65°
10°
max. 1440 56 3/4”
min. 970 38 1/8”
SIROLUXLEDview

2 Dimensions, technical data Sirona Dental Systems GmbH
2.1 C8+1:20 Installation Requirements C8+/C8
+Tu r n
60 28 000 D3417
20 D3417.021.04.11.02
C8+1:20
*** Depending on the chair height
max. 380 +15
15“ +5/8”
1170
46”
860
33 7/8”
1210
47 1/2”
310
12 1/4”
150
140
2070 +50***
81 1/2” +2“ ***
45
1 3/4”
459
18”
430 +15
17“ +5/8”
180
7”
90°
90° 90°
60°
750
29 1/2”
770
30 3/8”
250
9 7/8”