Sirona Sinius CS User manual

New as of:
Installation Requirements
03.2017
Sinius / Sinius CS / Sinius TS
English
=
Installation requirements

63 22 668 D3561
D3561.021.01.09.02 03.2017 3
Dentsply Sirona Table of contents
Installation Requirements Sinius / Sinius CS / Sinius TS
båÖäáëÜ
Table of contents
1General information................................................................................................. 5
1.1 Notes on the installation prerequisites ......................................................... 5
1.2 Structure of the document............................................................................ 6
1.2.1 Identification of the danger levels.................................................... 6
1.2.2 Formats and symbols used ............................................................. 6
2Safety information.................................................................................................... 7
2.1 Installation by qualified personnel ................................................................ 7
2.2 Radiotelephones .......................................................................................... 7
2.3 Modifications and extensions of the system................................................. 7
2.4 Power connection......................................................................................... 8
3On-site installation................................................................................................... 9
3.1 Substrate, floor............................................................................................. 9
3.1.1 Load-bearing capacity of the floor................................................... 9
3.1.2 Tensile forces.................................................................................. 9
3.1.3 Stability............................................................................................ 10
3.2 Requirements of the supply media............................................................... 11
3.2.1 Requirements of the water supply................................................... 12
3.2.1.1 Condition of the water....................................................... 12
3.2.1.2 Connection to the public drinking water system ............... 13
3.2.1.3 Installation of the water supply on the building side ......... 14
3.2.2 Requirements of the air supply........................................................ 15
3.2.2.1 Condition of the air ........................................................... 15
3.2.2.2 Installation of air supply.................................................... 15
3.2.3 Requirements of the suction machine............................................. 16
3.2.3.1 Typical pressure loss in the suction system ..................... 16
3.2.4 Requirements of the waste water installation.................................. 17
3.3 Underfloor installation of supply lines........................................................... 18
3.3.1 Installation template ........................................................................ 18
3.3.2 Installation of the supply lines in the termination panel ................... 20
3.4 Cleaning the air and water pipes.................................................................. 21
3.5 Underfloor installation of the PC connections .............................................. 22
4Dimensions, technical data...................................................................................... 24
4.1 Sinius dimensions, scale bar 1:20................................................................ 24
4.1.1 Distances in the treatment room ..................................................... 24
4.1.2 Side view ......................................................................................... 25
4.1.3 Top view.......................................................................................... 26

63 22 668 D3561
4D3561.021.01.09.02 03.2017
Table of contents Dentsply Sirona
Installation Requirements Sinius / Sinius CS / Sinius TS
4.1.4 Top view with options....................................................................... 27
4.1.5 Distances in the treatment room with Heliodent Plus....................... 28
4.1.6 Side view with HELIODENT Plus..................................................... 29
4.2 Sinius CS dimensions, scale bar 1:20........................................................... 30
4.2.1 Distances in the treatment room ...................................................... 30
4.2.2 Side view.......................................................................................... 31
4.2.3 Top view........................................................................................... 32
4.2.4 Top view with options....................................................................... 33
4.2.5 Distances in the treatment room with Heliodent Plus....................... 34
4.2.6 Side view with HELIODENT Plus..................................................... 35
4.3 Sinius TS dimensions, scale bar 1:20 ........................................................... 36
4.3.1 Distances in the treatment room ...................................................... 36
4.3.2 Side view.......................................................................................... 37
4.3.3 Top view........................................................................................... 38
4.3.4 Top view with options....................................................................... 39
4.3.5 Distances in the treatment room with Heliodent Plus....................... 40
4.3.6 Side view with HELIODENT Plus..................................................... 41
4.4 Mounting plates............................................................................................. 42
4.5 Information on planning for the practice........................................................ 44
4.6 Technical data............................................................................................... 45
4.6.1 Operating, transport and storage conditions .................................... 47
4.6.2 Weight and packaging...................................................................... 48
4.7 Standards/Approvals..................................................................................... 49
5Electromagnetic compatibility................................................................................... 51
5.1 Accessories................................................................................................... 51
5.2 Electromagnetic emission ............................................................................. 52
5.3 Interference immunity.................................................................................... 53
5.4 Working clearances....................................................................................... 56
5.5 Foot control wireless interface ...................................................................... 57
6Checklist................................................................................................................... 58
6.1 Installation site .............................................................................................. 58
6.2 Construction requirements ............................................................................ 59
6.3 IT hardware ................................................................................................... 60
6.4 Network ......................................................................................................... 60
6.5 Data processing ............................................................................................ 61

63 22 668 D3561
D3561.021.01.09.02 03.2017 5
Dentsply Sirona 1General information
Installation Requirements Sinius / Sinius CS / Sinius TS 1.1Notes on the installation prerequisites
båÖäáëÜ
1General information
1.1 Notes on the installation prerequisites
This document describes the installation prerequisites for all versions of
the Sinius / Sinius CS / Sinius TS treatment center.
It contains the following information:
● Required information for practice planning.
● Information for the installer and operator regarding the necessary
quality of the air and water supply media.
● Information for the installer, such as how to implement the
connections for air, water, waste water, suction air and the power
supply.
● Information on the cabling of the PCs to be connected.
● Information about electromagnetic compatibility and the prerequisites
for setting up the treatment center.
● A checklist to ensure that all installation requirements have been
fulfilled.
The subsequent installation of the treatment center is described in the
installation instructions (REF 6322627).
You will also need the drilling template (REF 63 34 291) for the safe and
secure attachment of the treatment center to the floor.

63 22 668 D3561
6D3561.021.01.09.02 03.2017
1General information Dentsply Sirona
1.2Structure of the document Installation Requirements Sinius / Sinius CS / Sinius TS
1.2 Structure of the document
1.2.1 Identification of the danger levels
To prevent personal injury and material damage, please observe the
warning and safety information provided in this document. This
information is highlighted as follows:
Tip: Information for facilitating work.
1.2.2 Formats and symbols used
The formats and symbols used in this document have the following
meaning:
DANGER
An imminent danger that could result in serious bodily injury or death.
WARNING
A possible dangerous situation that could result in serious bodily injury
or death.
CAUTION
A possible dangerous situation that could result in slight bodily injury.
NOTICE
A possible harmful situation which could lead to damage of the product
or an object in its environment.
IMPORTANT
Application instructions and other important information.
Prerequisite
1. First action step
2. Second action step
or
➢Alternative action
Result
➢Individual action step
Requests you to do something.
see “Formats and symbols
used [ → 6]”
Identifies a reference to another text
passage and specifies its page
number.
● List Identifies a list.
“Command / menu item” Identifies commands, menu items, or
quotations.

63 22 668 D3561
D3561.021.01.09.02 03.2017 7
Dentsply Sirona 2Safety information
Installation Requirements Sinius / Sinius CS / Sinius TS 2.1Installation by qualified personnel
båÖäáëÜ
2Safety information
2.1 Installation by qualified personnel
The installation of the supply connections must be carried out by qualified
technicians only.
Electrical and water supply installations; reference for INST suctionmachines
2.2 Radiotelephones
Mobile RF communications equipment can affect electro-medical
equipment. Therefore, the use of mobile wireless phones in medical office
or hospital environments must be prohibited.
2.3 Modifications and extensions of the system
Modifications to this unit which might affect the safety of the system
owner, patients or other persons are prohibited by law.
For reasons of product safety, this product may be operated only with
original Dentsply Sirona accessories or third-party accessories expressly
approved by Dentsply Sirona. The user is responsible for any damage
resulting from the use of non-approved accessories.
If any units not approved by Dentsply Sirona are connected, they must
comply with the applicable standards, e.g.:
● IEC 60950-1 or IEC 62368-1 for information technology equipment
(e.g. PC, Ethernet switch, Ethernet hub, Ethernet converter, USB
repeater, Ethernet router, USB switch, HDMI repeater/amplifier,
audio sources, display port repeater/amplifier, etc. and their power
supply units), as well as
● IEC 60601-1 for medical devices.
The treatment center monitor must fulfill the requirements of the
IEC 60950-1 or IEC 62368-1 standard.
The loudspeaker port of the monitor may only be connected to a device
that complies with the IEC 60950-1, IEC 62368-1 (e.g. a PC) or IEC
60601-1 standard. Under no circumstances may it be connected to a
stereo system or similar.
If a system is created during the installation process, the requirements of
IEC 60601-1, 3rd edition, must be fulfilled. The system author assumes
responsibility for conformity of the system with 93/42/EEC Directive, for
example.
WARNING
Professional installation
Comply with the national regulations for electrical installation
(e.g. IEC 60364-1, VDE 0100-100, IEC 60364-7-710, VDE 0100-710,
National Electrical Code).
Comply with the national regulations for water supply installations
(e.g. EN 1717) and sewage installations (e.g. EN 12056-1).

63 22 668 D3561
8D3561.021.01.09.02 03.2017
2Safety information Dentsply Sirona
2.4Power connection Installation Requirements Sinius / Sinius CS / Sinius TS
2.4 Power connection
WARNING
Shock hazard
It is essential that you switch off the power supply PRIOR to beginning
the installation. There is a risk of electric shock. People can be injured
or electrical components of the unit destroyed.

63 22 668 D3561
D3561.021.01.09.02 03.2017 9
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.1Substrate, floor
båÖäáëÜ
3On-site installation
3.1 Substrate, floor
Unevenness The floor must be level and horizontal in accordance with DIN 18 202.
In the case of an uneven floor, the steel adapter plate must be used; see
Mounting plates [ → 42].
3.1.1 Load-bearing capacity of the floor
Load capacity:
The minimum load-bearing capacity of the floor must be 0.5 N/cm2
(corresponds to around 500 kg/m2).
3.1.2 Tensile forces
The floor must be able to accommodate tensile forces of > 1 kN at each
of the marked screw fastening points (A).
It may be necessary to reinforce the surface beneath the floor.
When using a mounting plate (see Mounting plates [ → 42]) this
requirement is mandatory.
0,5
N/cm20,7
lbs/sq in.
A

63 22 668 D3561
10 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.1Substrate, floor Installation Requirements Sinius / Sinius CS / Sinius TS
3.1.3 Stability
With a concrete floor
● Use a 12 mm dia. masonry drill to drill the holes.
● The depth of the drill hole (C) in the concrete floor must be at least 80
mm.
● The specified drilling depth (C) of at least 80 mm refers to the drilling
length without screed (A) or impact sound insulation (B). The heavy
duty anchor bolts included with delivery (2 units) are suitable for a
clamping length ((A)+(B)) of up to 100 mm.
● Use 12 mm dia. wall plugs (but do not use wall plugs instead of heavy
duty anchor bolts).
● Use 10x160 mm wood screws including washers.
With a wooden floor
● Provide and prepare appropriate supporting beams.
● Use a 7mm dia. wood drill to drill the holes.
● The depth of the drill hole must be at least 80mm.
● Use 10x80mm wood screws including washers.
ATTENTION! Do not use wall plugs!
Ø 12mmØ 12mm
20mm
7mm
160
mm
160
mm
80
mm
min.
80
mm
min. C
B
A
100
mm
max.
100
mm
max.
WARNING
Any existent screed (A) and/or impact sound insulation (B) must be
penetrated!
Ø 7mmØ 7mm
7mm
80
mm
min.
80
mm
min.

63 22 668 D3561
D3561.021.01.09.02 03.2017 11
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.2Requirements of the supply media
båÖäáëÜ
3.2 Requirements of the supply media
Suction machine
Compressed air (free from oil)
The compressor must be able to draw in air in an efficient,
hygienic manner.
Cold water (drinking water quality)
K Steam trap

63 22 668 D3561
12 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.2Requirements of the supply media Installation Requirements Sinius / Sinius CS / Sinius TS
3.2.1 Requirements of the water supply
3.2.1.1 Condition of the water
The water that supplies the treatment center must meet the following
requirements to avoid operating faults.
Water pressure: 2.5bar (36psi) to 6bar (87psi)
Minimum
flow rate:
3 l/min
Water hardness
(overall
hardness):
at > 2.4 mmol/l (= 12° dH),
install a water softener.
Set dilution hardness to 1.43 mmol/l (= 8° dH).
pH value: 6.5 to 8.5 (recommended)
Particle size: ≤ 100 µm
Water quality: The water quality must comply with the national
requirements for drinking water.
Colony count: The colony count must fulfill the national regulations
for drinking water and must not exceed 500 CFU/ml
under any circumstances (CFU: Colony forming
units).
In the event of an increased colony count, the indoor
installation must be checked and the cause of
contamination eliminated. Alternatively you can also
change over to a stand-alone water supply for a brief
period.
Sampling and the colony count must be performed
by a competent laboratory.
Before installation of the treatment center, an
acceptable microbiological water quality for the
domestic water supply must be ensured and
documented in the form of a colony count.

63 22 668 D3561
D3561.021.01.09.02 03.2017 13
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.2Requirements of the supply media
båÖäáëÜ
3.2.1.2 Connection to the public drinking water system
Treatment center isolated from the public drinking water supply
The treatment center, if it is equipped with a disinfection system, complies
with the requirements of EN 1717 (free discharge with an isolation
distance ≥ 20 mm) and the DVGW German Gas and Water Association).
It is intrinsically safe according to the W540 worksheet and thus also
complies with W270 and KTW (Guideline on the use of plastics in contact
with drinking water). It can be connected directly to the public drinking
water system.
The treatment center then has the "DVGW" label next to the rating plate.
Treatment center not isolated from the public drinking water supply
If compliance with EN 1717 is required in the country, the respective
measures for the protection of public drinking water must be taken
outside the treatment center.
This applies to models without a disinfection system.
The treatment center then does not have the "DVGW" label.
Please comply with the national requirements with regard to connecting
treatment centers to the public drinking water system.

63 22 668 D3561
14 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.2Requirements of the supply media Installation Requirements Sinius / Sinius CS / Sinius TS
3.2.1.3 Installation of the water supply on the building side
● Carry out the installation in accordance with the national installation
requirements (e.g. EN 1717).
● Connect the treatment center to the cold water supply.
● Use fine filters with a mesh size between ≤ 80 µm (0.08 mm) and ≤
100 µm (0.1 mm).
● In order to reduce the microorganisms in the water supply pipe, take
account of the following when laying this pipe to the treatment center:
– Avoid long stub lines to the treatment center.
– Carry out the installation so that, where possible, other main
consumers (such as the sink) are fed from the same line
downstream of the treatment center connection.
– Avoid laying the supply line parallel to hot water pipes.
● Recommendation: Install a corner valve in the water supply to the
treatment center with 2 outlets and 2 stopcocks. The second outlet
makes it easy to take a sample of the water for microbiological
testing.

63 22 668 D3561
D3561.021.01.09.02 03.2017 15
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.2Requirements of the supply media
båÖäáëÜ
3.2.2 Requirements of the air supply
The air supply is required to drive the turbines, cool the drill drives, for the
cooling spray and to control the treatment center.
3.2.2.1 Condition of the air
3.2.2.2 Installation of air supply
● Carry out the installation in accordance with the national
requirements.
● Install a steam trap.
Air pressure: 5.5bar (80psi) to 7.5bar (109psi)
Minimum flow rate: 50l/min
Minimum flow rate with air
jet pump:
80 l/min
Air humidity: Dew point ≤ -20°C at atmospheric pressure
Oil content: ≤ 0.5mg/m3
Particle content: ≤ 100 particles of size 1 - 5 µm
in one m3 of air
(larger particles are filtered by the treatment
center.)
Hygiene: Hygienically acceptable air
IMPORTANT!
The treatment center does not require
medical air.

63 22 668 D3561
16 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.2Requirements of the supply media Installation Requirements Sinius / Sinius CS / Sinius TS
3.2.3 Requirements of the suction machine
● Vacuum in the suction machine at the connection point with the
treatment center: min. 0.12 bar (1.7 psi), max. 0.18 bar (2.6 psi).
● With a vacuum of > 0.18 bar (2.6 psi) with no flow, the treatment
center must be fitted with the "Vacuum limiter" retrofit kit (REF 59 68
826).
● Minimum suction power: 500 Nl/min
● For the suction line: adhere to the specifications in the installation
instructions for "Suction machines".
● Suction system Type 1: High flow rate
● Wet or dry suction (depending on equipment)
● Suction handpiece diameter:
– 6 mm: Saliva ejector and surgical suction
– 11 mm: Spray aspirator
● Filter mesh size 1.8 x 2.6 mm
● Sirona recommends using cannulae with a bypass in order to prevent
return flow in adhered cannulas.
3.2.3.1 Typical pressure loss in the suction system
Suction flow of large suction hose
red ( ○ ): Only large suction device
black ( ◊ ): Saliva ejector in parallel

63 22 668 D3561
D3561.021.01.09.02 03.2017 17
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.2Requirements of the supply media
båÖäáëÜ
3.2.4 Requirements of the waste water installation
● The quantity of waste water from the treatment center is max. 3 l/min.
– Carry out the waste water installation accordingly.
– Fit the waste water pipe in accordance with the information in the
table.
The gradient of the waste water pipe must be at least 1°.

63 22 668 D3561
18 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.3Underfloor installation of supply lines Installation Requirements Sinius / Sinius CS / Sinius TS
3.3 Underfloor installation of supply lines
3.3.1 Installation template
We recommend that you order the installation template (REF 33 15 830)
from Sirona for laying the pipe ends in the installation field.
If necessary, you can also prepare the template yourself based on the
diagram below.
The specified dimensions of the segments are the dimensions of the core
boreholes.

63 22 668 D3561
D3561.021.01.09.02 03.2017 19
Dentsply Sirona 3On-site installation
Installation Requirements Sinius / Sinius CS / Sinius TS 3.3Underfloor installation of supply lines
båÖäáëÜ
1 Water supply
Pipe 10x1 mm, corner valve outlet 3/8"
2 Compressed air supply
Pipe 10x1 mm, corner valve outlet 3/8"
3 Suction line
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter approx. 36.5 mm)
4 Water drainage
DN40 HT-PP ISO 8283-3
(polypropylene, inner diameter approx. 36.5 mm)
5 Installation pipe (power supplies)
inner diameter approx. 40 mm)
6 Control cable to relays for the
suction machine ( ),
call cable ( ),
Special function (#)
3 x 1.5 mm2 (AWG16) (quality as in the power cable)
7 Power supply
3x1.5 mm2 (AWG16)
Circuit breaker: for 230 V AC: 16 A medium-blow
for 100 - 115 V AC: 20 A medium-blow
Recommendation: Type B automatic circuit breaker
8Option: Heliodent Plus radiation cable (10 m)
(free end 300 ± 50 mm)
CAUTION
The Heliodent Plus radiation cable cannot be laid together
with USB or HDMI cables. If required, allow for a separate
installation pipe.
9 Installation pipe (IT)
inner diameter min. 50 mm
(or corresponding flat conduit) for the PC connection
%

63 22 668 D3561
20 D3561.021.01.09.02 03.2017
3On-site installation Dentsply Sirona
3.3Underfloor installation of supply lines Installation Requirements Sinius / Sinius CS / Sinius TS
3.3.2 Installation of the supply lines in the termination panel
✔An installation template is available or was prepared.
1. Check the position of the supply lines against the installation template
as per the practice blueprint. Ensure that sufficient space is provided
between the lines and the walls; see "Scale 1:20". The center of the
hole in the floor must be 269 mm (10 5/8") from the foot of the
treatment center.
2. Lay the ends of the supply pipes, corner valves and lines as shown in
the illustrations.
ªThe top edge of the corner valves for air and water must not project
more than 60 mm from the top edge of the floor.
ªThe suction and drainage pipes must be flush with the top edge of the
floor (a deviation of +5 mm is permissible). The inner diameter of both
pipes is 36.5 mm.
ªThe electric lines must project by at least 500 mm.
ªThe supply lines are laid.
Ø 50 mm Ø 36,5 mm
>500mm
>20“
< 3/16“
< 5mm
< 60mm
< 2 3/8“
Ø 36,5 mm
3/8“