SMITH SYSTEM 04157 User manual

Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
ASSEMBLY INSTRUCTIONS
Special Notes:
1. Check that all compenents are accounted for and undamaged before assembling.
2. Please assemble product in a clean, dry area.
3. For larger units, you may need assistance from another individual to assemble the unit.
4. Clean the product with a mild cleaner and a damp cloth.
smithsystem.com | 1 800 328 1061
Form #179991@kbo(&'-

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
HARDWARE PACK #67607 (INTERCHANGE ACTIVITY)
Part Number Description Quantity
A#77813 3/16” Allen Wrench (2)
B#70867 Connector Bolt
1/4 - 20 x 23mm (4)
C#70869 Connector Nut
1/4 - 20 x 17mm (4)
D#70054 #10 x 3/4”
Wood Screws (26)
Ac
BD
x2
x4
x4
x26
INTERCHANGE CRESCENT TABLETOP
Part Number Description Quantity
#04156 72” Crescent Top (1)
OR
#04157 60” Crescent Top (1)
INTERCHANGE CRESCENT LEG SET
Part Number Description Quantity
#79804 72” Crescent Leg Set (1)
OR
#79803 60” Crescent Leg Set (1)
Form #179991@kbo(&'-

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
INTERCHANGE 5TH LEG SET #79528 (04156)/ 79529 (04157)
Item # Part Number Description Quantity
1#P12925 Interch. Crescent
SLEG BRKT. (1)
2#P10506 Ellipse Leg, Single,
Ellipse (1)
370201 Nyloc Bolt -
1/4 - 20 Thread (2)
4#1_4-20 x
500_SCREW
1/-20 x .500 PAN
HEAD Phillips w/
Nylon Patch
(2)
5#P12923 T-NUT BRKT -
Crescent Single Leg (1)
6#70054 #10 x 3/4”
Hi Lo Path Screw (6)
41.75”
OR
51.75”
Form #179991
@kbo(&'-
7#77536 or 77508
(04156) (04157)
51.76” or 41.75”
Support Channel
(1)
8#77513 Support Channel
Brackets (Pair)
(1)
7
8
8

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
STEP 1: Place the top on a clean,dry surface laminate side down, so that the
predrill holes face up.
STEP 2: Loosely attach the channel brackets (#77513) and support
channel (#77536/77508) assembly using the (4) connector nuts from
hardware pack that came with the leg set.
See figure 1A
FIGURE 1A
FIGURE 1
Form #179991
@kbo(&'-

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
STEP 3: Align the slots of the leg assemblies to the pre-drilled holes of the
top - using the 3/4” wood screws that came with the leg set,
attach the leg assembly to the top.
*tip* stagger screws during assembly; i.e. fasten one screw into one of the legs, then
another screw on the other leg. Continue to stagger until all screws are used.
STEP 4: Tighten the connector bolts and nuts to the leg sets using the two
Allen Keys provided.
FIGURE 2
Form #179991
@kbo(&'-

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
STEP 5: Rotate the T-Nut bracket 90º and insert into channel support.
Loosely attach 1 / 4-20 screws through the single leg bracket
(#26663). Maneuver single leg bracket until screw holes align with
predrilled holes in the top - Install Screws.
FIGURE 3
Form #179991
@kbo(&'-

smithsystem.com | 1 800 328 1061
Crescent 60” . . . . . . . . . . # 04157
Crescent 72” . . . . . . . . . . # 04156
INTERCHANGE CRESCENT
STEP 6: Adjust the leg height as desired by loosening the set screw in each
leg (using the Allen Key provided). Move leg to desired height -
and be sure to locate the appropriate hole in the leg.
DO NOT USE A POWER TOOL FOR LEG ADJUSTMENT!
HAND TIGHTEN WITH ALLEN KEY ONLY!
STEP 7: Use the help of at least one other individual to turn the table over
and into it’s upright position.
FIGURE 4
Form #179991
@kbo(&'-