SOMFY Altus RTS 120 V Operating instructions

To change the lower limit
Send the shade to it’s current
lower limit.
To change the upper limit
Send the shade to it’s current
upper limit.
Adjusting the limits in User Mode
Press until the shade jogs
Press both and at the same
time until the shade jogs. Adjust to
a new lower limit position.
Press both and at the same
time until the shade jogs. Adjust to
a new upper limit position.
Press until the shade jogs
Note
If shade is actively moving (in-motion) Should be pressed twice.
To Delete: Activate shade to intermediate position, then press and
hold (stop) for 5 seconds. Shade will jog to confirm deletion.
Setting
Press the or to operate shade. At the desired intermediate
(preferred) position press (Stop) to stop the shade.
Once the desired Intermediate position is reached, Press and
hold (stop) until the shade jogs. The Intermediate position
is now added to memory
Using
Send the shade to the intermediate position by pressing (stop)
from ANY shade position.
Note: Shade should be stationary prior to activating intermediate
position function.
Setting an Intermediate Position (Preferred Position)
Adding or deleting a Transmitter or a Channel
Programmed Transmitter
STEP 1:
STEP 2:
Transmitter to add or delete
STEP 3:
STEP 4:
Using already programmed transmitters select the transmitter (single channel) or the channel, (1-5)
of a multi-channel transmitter.
Press and hold the programming button of that transmitter until the shade jogs.
Select the transmitter (single channel) or the channel, (1-5) of a multi-channel transmitter, to be
added or deleted.
Press and hold the programming button of that transmitter until the shade jogs.
Progammmed
Transmitter
Transmitter To Add
Or Delete
To change the lower limit
Send the shade to it’s current
lower limit.
To change the lower limit
Send the shade to it’s current
lower limit.
Programming Mode
STEP 1: Connect power
With the motor installed in shade, connect power to
the motor (120V, or 12 V or 24V transformer or 12 V
battery wand)
STEP 2: I
Press both and at the same time until the shade
jogs. In Programming
Mode, the shade will move only when the or is held
nitiate programming
A jog is a brief up and down motion.
STEP 3:
Press or . When pressing product should
go down or out. To change direction press and hold
(Stop) until the shade jogs.
Check directions
A jog is a brief up
and down motion.
STEP 4: Set the limits
Bring the shade to desired upper limit stop point. Press both
(Stop) and until the motor moves, then release. (If the shade
stops when the buttons are released take it back to the upper limit
and repeat) Stop the motor when reaching the desired lower limit.
You can adjust by pressing or
STEP 5: Set the limits
Press both (Stop) and at the same time until the
shade moves, then release. The shade will stop at the original
upper limit.
STEP 6: Confirm
Press and hold (stop) until the shade jogs to confirm
the limit settings.
limit settings
A jog is a brief up and down motion.
STEP 7: Set user mode
Press and hold the programming button on the
back of the transmitter until the shade jogs. The
shade is now in User Mode. In User Mode, the
shade will operate with a brief press on or
Double check limit settings as a precaution.
QUICK PROGRAMMING GUIDE FOR ALL RTS MOTORS
Altus RTS 120 V / Sonesse 30
Please refer to individual instructions for more details
TM TM
24V / Wirefree Roll Up LT-30RT Round Head & CORD Lift CT-32 Motors.
Before you begin
Motors are shipped without limit settings and transmitter ID’s. Steps 1 to 7 must
be completed to ensure proper shade programming and functionality. Power should
ONLY be connected to current shade being programmed. All other shades should be
disconnected from their respective power while programming

1 2 3 4
To delete all previous settings: Using a paper clip, press and hold the PROGRAM button located on the motor
head. The LED will light then blink; release the button when the LED turns off. If you cannot see the LED, push
and hold the programming button for 15 seconds, and then release the button. All transmitters and limits will
be erased. (Motor is now reset to factory mode). Motor limits will need to be reestablished. See Programming
Mode (step 4&5) for limit setting.
TM
Resetting WIREFREE ROLL UP MOTORS LT-30RT Round Head 12V DC
To delete all previous settings: press and (approximately 15 ) until
the LED blinks rapidly then extinguishes. All transmitters and limits will be erased. (Motor is now reset
to factory mode). Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for
limit setting.
hold the PROGRAM button seconds
TM
Resetting WIREFREE CORD LIFT MOTORS CT-32 12V DC
To delete all previous settings: PROGRAM button (approximately
15 seconds) until the shade jogs 3 times. All transmitters and limits will be erased. (Motor is now reset to
factory mode). Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for limit
setting.
Using a paperclip, press and hold the red
TM
Resetting Sonesse 30 24V DC
2 Seconds 10 Seconds 2 Seconds Shade starts to move.
Resetting Altus RTS 120 V AC
Perform a Dual Power Cut to delete all previous settings When the shade stops press and
hold the programming button
of any transmitter until the
shade jogs twice.
Do not release the programming
button until the jogging is
complete or you will have to
start the dual power cut from
the beginning.
Activating Step (Tilting) Feature for Sheer Shade Applications
(With )
TM
WIREFREE ROLL UP MOTORS LT-30RT Round Head only
1) Press , shade will travel to pre-set DOWN limit.
2) Press and hold until shade begins to “step” or tilt.
3) Release once new position is reached.
© SOMFY ULC 02/09Tel. [phone]
To delete all previous settings: Using a paperclip, press and hold the PROGRAM button, located on the top of
the motor casing for 12 seconds. All transmitters and limits will be erased. (Motor is now reset to factory mode.)
Motor limits will need to be reestablished. See Programming Mode (Step 4&5) for limit setting.
TM
Resetting TILT WIREFREE RTS MOTORS 12V DC
Program
Button
Insert reset tool into
connector on motor.
Program
Button
Program
Button
TI N
B Y