SOMFY WIREFREE LT-30RT Operating instructions

Note
If shade is actively moving (in-motion)
Should be pressed twice.
To Delete: Activate shade to intermediate
position, then press and hold (stop)
for 5 seconds. Shade will jog to confirm
deletion.
Press both and at the same time until the motor jogs
Adjust to a new lower limit position. Press until the motor jogs
Press both and at the same time until the motor jogs.
Adjust to a new upper limit position. Press until the motor jogs
STEP 6: Confirm limit settings
Press and hold (stop) until
the motor jogs to confirm the
limit settings.
STEP 5: Set the limits
Press both (stop) and
at the same time until the
motor moves, then release.
The motor will stop at the
original upper limit.
STEP 2: Initiate programming
Press both and at the
same time until the motor
jogs.
In programming mode the
motor operates in momentary
fashion.
STEP 1: Connect power
With the motor installed in shade
connect power to the motor
(120V, or 12 V or 24V transformer
or 12 V battery wand)
Before you begin
Motors are shipped without limit settings and transmitter ID’s.
Steps 1 to 7 must be completed to ensure proper shade programming and functionality.
It is recommended to power only the motor being programmed (disconnect power to all the other motors)
Motor will exit programming mode after 2 minutes of inactivity.
STEP 4: Set the limits
Bring the motor to desired
upper limit. Press both
(stop) and until the
motor moves, then release.(If
the motor stops when the buttons are
released take it back to the upper limit
and repeat) Stop the motor when
reaching the desired lower
limit. You can adjust by
pressing or
STEP 3: Check directions
Press or
When pressing product
should go down or out.
To change direction press and
hold (stop) until the
motor jogs (shade has a short up and
down movement)
STEP 7: Set user mode
Press and hold the
programming button on the
back of the transmitter until
the motor jogs. It will now
operate in a maintained
fashion (user mode).
Double check limit settings as
a precaution.
To change the lower limit
Send the motor to it’s current lower limit.
To change the upper limit
Send the motor to it’s current upper limit.
QUICK PROGRAMMING GUIDE FOR ALL RTS MOTORS
TM
WIREFREE ROLL UP LT-30RT Round Head and CORD LIFT CT-32 MOTORS
Please refer to individual instructions for more details
Programming Mode
Adjusting the limits in User Mode
Setting
Send the shade and stop it at
the desired intermediate
position by pressing (stop)
Once the desired Intermediate
position is reached, Press and
hold (stop) until the shade
jogs. The Intermediate position
is now added to memory
Using
Send the shade to the
intermediate position by
pressing (stop) from ANY
shade position..
Note: Shade should be
stationary prior to activating
intermediate position
function.
Setting an Intermediate Position
A jog is a brief up and down motionA jog is a brief up and down motion

To delete all previous settings: Using a paper clip, press and hold the PROGRAM button located
on the motor head. The LED will light then blink; release the button when the LED turns off. If you
cannot see the LED, push the programming button for 15 seconds, and then release the button. All
transmitters and limits will be erased. (Motor is now reset to factory mode). Motor limits will need to
be reestablished.
Program
Button
To delete all previous settings: press and hold the PROGRAM button (approximately 15 seconds)
until the LED blinks rapidly then extinguishes.
All transmitters and limits will be erased. (Motor is now reset to factory mode). Motor limits will need to
be reestablished.
TM
Resetting WIREFREE CORD LIFT MOTORS CT-32
TM
Resetting WIREFREE ROLL UP MOTORS lt-30rt Round Head
Insert reset tool into
connector on motor.
Adding or deleting a Transmitter or a Channel
STEP 3:
STEP 4:
Select the transmitter (single channel) or
the channel, (1-5) of a multi-channel
transmitter, to be added or deleted.
Press and hold the programming button
of that transmitter until the motor jogs.
STEP 1:
STEP 2:
Using already programmed transmitters
select the transmitter (single channel) or
the channel, (1-5) of a multi-channel
transmitter.
Press and hold the programming button
of that transmitter until the motor jogs.
Prmd
rogame
Tra st
nmitre
Ts i t
ranmter
oado
Tdr
De
elte
© SOMFY ULC 05/07
Program
Button
1-800-22SOMFY