SOMFY Sonesse 40 RTS User manual

www.somfy.com
Sonesse®40 RTS
Ref: 5064823A

1Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
Installation instructions page 2
SOMFY hereby declares that this product complies with the essential requirements and
other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity is available
at the web address www.somfy.com/CE. Suitable for use in EU, CH and NO
EN
EN

2Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
CONTENT
1 Introduction
2 Safety
2.1 General information
2.2 General safety advice
3 Wiring
4 Commissioning
4.1 Programming the RTS transmitter
4.2 Checking the rotation direction
4.3 Adjusting the end limits
4.4 Recording the RTS transmitter
4.5Favorite position : MY position
Recording MY position.
5 Use
5.1 Up, Down, My: In roller mode
6Modifying the settings
6.1 End limit re-adjustement
6.2 Favorite position : MY position
Changing the MY position / Delete the MY position
6.3 Modifying the motor rotation direction
6.4 Modifying the wheel rotation direction
6.5 Scroll wheel increment setting
6.6 Replacement of a lost remote control
6.7 Adding/Deleting RTS transmitter
6.8 Adding/Deleting RTS sensors
6.9 Erase the memory of the motor
7Troubleshooting
8Technical data
9Environment

3Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
1 Introduction
Product Description
The Sonesse®40 is a motor specially dedicated to interior applications.
The Sonesse®40 motor range can motorize all interior applications: Roller shades, Vene-
tian blinds, Roman shades, Pleated & cellular shades, Projection screens.
The Sonesse®40 is designed to ensure quiet operations.
Warning: The Sonesse®40 isn’t compatible with wind functions.
2 Safety
2.1 General information
7KLV6RPI\SURGXFWPXVWEHLQVWDOOHGE\DSURIHVVLRQDOPRWRULVDWLRQDQGKRPHDXWRPD-
tion installer, for whom these instructions are intended.
%HIRUHLQVWDOODWLRQFKHFNWKDWWKLVSURGXFWLVFRPSDWLEOHZLWKWKHDVVRFLDWHGHTXLSPHQW
and accessories.
7KHVHLQVWUXFWLRQVGHVFULEHKRZWRLQVWDOOFRPPLVVLRQDQGXVHWKLVSURGXFW
0RUHRYHUWKHLQVWDOOHUPXVWFRPSO\ZLWKFXUUHQWVWDQGDUGVDQGOHJLVODWLRQLQWKHFRXQWU\
in which the product is being installed, and inform his customers of the operating and
maintenance conditions for the product.
$Q\XVHRXWVLGHWKHVSKHUHRIDSSOLFDWLRQVSHFL¿HGE\6RPI\LVQRWDSSURYHG6XFKXVH
or any failure to comply with the instructions given herein will invalidate the warranty, and
Somfy refuses to accept liability.
6SHFL¿FVDIHW\DGYLFH
The safety instructions that must be observed, besides the usual rules, are
explained in these instructions and in the attached «Safety Instructions» document.
Never immerse the
motor in liquid!
Never drill holes in
the motor!
Avoid impacts!
Do not drop it!

3
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
3 Wiring
Wiring
1) Switch off the power supply.
2) Connect the motor according to the
information in the table below.
%OXH %URZQ
White %ODFN
1 Neutral 2 Live
RANGE
230V-50HZ
120V-60HZ
%OXH %URZQ
220V-60HZ
NA
Green
3 Earth
NA
1
2
OFF
3 x 1,5 mm 3 x 0,75 mm2
2
3
1
2
3

4
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
4 Commissioning
4.1 Programming the RTS transmitter
Switch on the power supply.
Press the UP and DOWN buttons
simultaneously on the RTS transmitter: the jogs
PRYHXSDQGGRZQEULHÀ\DQGWKHWUDQVPLWWHU
is preprogrammed in the motor
4.2 Checking the rotation direction
1) Press the RTS transmitter UP button:
a) If the shade is raised (a), the rotation
direction is correct: move to the section entitled
«Adjusting the end limits».
b) If the shade is lowered (b), the rotation
direction is incorrect: move to the next step.
2) Press the RTS transmitter MY button until
the shade jogs: the rotation direction has been
PRGL¿HG
3) Press the RTS transmitter UP button
WRFKHFNWKHURWDWLRQGLUHFWLRQ
4.3 Adjusting the end limits
The limits can be set in any sequence.
1) Press and hold the UP button to move the
shade to the desired Up position. If necessary
adjust the Up position, using the UP or DOWN
buttons.
2) Press the MY and DOWN buttons
simultaneously and release them once
the shade begins to move. The Up limit is
memorized.
3) Press the MY button when it reaches the
desired Down position.
If necessary adjust the Down position, using the
UP or DOWN buttons.
4)Press the MY and UP buttons simultaneously
and release them when the shade begins to
move.
The Down limit is memorized. The shade moves
up and will stop at its upper limit.
7RFRQ¿UPWKHHQGOLPLWVSUHVVDQGKROGWKH
MY button until the shade jogs. The end limits
are recorded.
1 2
34
5
1
32
a
b
=
=

5
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
4.4 Recording the RTS transmitter
After recording the end limit:
3UHVVEULHÀ\WKHSURJUDPPLQJEXWWRQRQWKH
EDFNRIWKHWUDQVPLWWHU7KHVKDGHMRJV
The transmitter is recorded.
OR
1) Switch off the current.
2) Switch on the current. The shade jogs.
3) Simultaneously press the UP and DOWN
buttons on the RTS transmitter.
The shade jogs.
3UHVVEULHÀ\WKHSURJUDPPLQJEXWWRQRQWKH
EDFNRIWKHWUDQVPLWWHU7KHVKDGHMRJV
The transmitter is recorded.
4.5 Favorite position: MY position
Recording MY position.
To set the MY position, move the shade to the
desired position with the UP and DOWN buttons
then press the MY button until the shade jogs.
1 2
3 4
PROG.
PROG.

6
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
5 Use
5.1 Up, Down, My: In roller mode
1) To move the shade from a limit to the other
OLPLWSUHVVEULHÀ\WKH83RU'2:1EXWWRQ
2) To stop the shade, press the MY button.
3) To move the shade to the MY position, press
EULHÀ\WKH0<EXWWRQ
1
2
3

7
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
6Modifying the settings
6.1 End limit re-adjustement
UP LIMIT
1) Press the UP button, to move the shade to
the limit to be readjusted.
2) Press and hold the UP and DOWN buttons
simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button to
move the shade to the new desired position.
7RFRQ¿UPWKHQHZOLPLWSUHVVDQGKROGWKH
MY button until the shade jogs.
DOWN LIMIT
1) Press the DOWN button to move the shade to
the limit to be readjusted.
2) Press and hold the UP and DOWN buttons
simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button to
move the shade to the new desired position.
7RFRQ¿UPWKHQHZOLPLWSUHVVDQGKROGWKH
MY button until the shade jogs.
6.2 Favorite position : MY position
1) Changing the MY position
To change the MY position go to the new desired
MY position with the UP and DOWN buttons
then press the MY button until the shade jogs.
2) Deleting the MY position
Press the MY button to move to this position
To delete the MY position, move to this position
and press the MY button until the shade jogs.
1 2
34
1 2
34
1
2

8
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
6.3 Modifying the motor rotation direction
Move the shade away from the end limits.
1) Press the UP and DOWN buttons
simultaneously until the shade jogs.
2) Press the MY button until the shade jogs to
reverse the rotation direction.
3UHVVWKH83EXWWRQWRFKHFNWKHQHZURWDWLRQ
direction.
The motor rotation direction is reversed.
1 2
3

9
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
A
PROG.
B
1
3
5
2
4
6.4 Replacement of a lost remote control
1%7KLVUHVHWGHOHWHVDOOWUDQVPLWWHUVSURJUDP-
med, but end-limits, intermediate position and
sensors are retained.
1%2QO\VZLWFKRIIWKHFXUUHQWIRUWKHPRWRU
where a transmitter is lost.
1) Cut the power supply for 2 seconds.
6ZLWFKWKHSRZHUVXSSO\EDFNRQIRUWR
seconds.
3) Cut the power supply for 2 seconds.
6ZLWFKWKHSRZHUVXSSO\EDFNRQWKHVKDGH
moves during 5 seconds (If the shade position
is an end limit, the behavior of the shade will
be a jog).
3UHVVWKH576WUDQVPLWWHU%352*EXWWRQ
until the shade jogs: all the RTS transmitters are
cleared and the new RTS transmitter is program-
med in the motor.
6.5 Adding/Deleting RTS transmitter
Find an RTS transmitter programmed in the
motor.
Press and hold the RTS programmed
transmitter (A) PROG button until the shade
jogs: the motor is in programming mode.
3UHVVEULHÀ\WKH576WUDQVPLWWHU%352*
button to add or delete this transmitter:
the shade jogs and the RTS transmitter is
programmed or deleted from the motor.
2 sec 10 to 15
sec
2 sec
PROG.
A
PROG.
B
A
B
A
A
A
B
B
PROG.
A
PROG.
B
+
-

10
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
6.6 Adding/Deleting RTS sensors
Find an RTS transmitter programmed in the
motor.
Press and hold the RTS programmed
transmitter (A) PROG button until the shade
jogs: the motor is in programming mode.
3UHVVEULHÀ\WKH576VHQVRU&352*EXWWRQ
to add or delete this sensor: the shade jogs
and the RTS sensor is programmed or deleted
from the
motor.
6.7 Erase the memory of the motor.
1%7KLVUHVHWGHOHWHVDOO576WUDQVPLWWHUV
RTS sensors, end-limits and intermediate
position programmed.
1%2QO\VZLWFKRIIWKHFXUUHQWIRUWKHPRWRU
to be reset!
1%%HIRUHFXWWLQJWKHSRZHUPRYHWKHVKDGH
to the middle position.
1) Cut the power supply for 2 seconds.
6ZLWFKWKHSRZHUVXSSO\EDFNRQIRUWR
15 seconds.
3) Cut the power supply for 2 seconds.
6ZLWFKWKHSRZHUVXSSO\EDFNRQWKHVKDGH
moves during 5 seconds (If the shade position
is an end limit, the behavior of the shade will be
a jog).
5) Press the RTS transmitter (A) PROG button
until the shade jogs twice: all the RTS transmit-
ters, RTS sensors, end-limits and intermediate
position are cleared.
10 to 15
sec
2 sec 10 to 15
sec
2 sec
+
-
2
4
3
1
5

11
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
7 Troubleshooting
The motor doesn’t work:
Verify:
7KHZLULQJRIWKHPRWRU
7KHSRZHUVXSSO\VSHFL¿FDWLRQV
7KHFRPSDWLELOLW\RIWKHFRQWURO
7KHKHDWJHQHUDWHGZDLWIRUWKHFRROLQJRIWKHPRWRU
The equipment stops too soon:
9HUL¿\
7KHRSHUDWLRQRIHQGOLPLWVGXULQJWKHURWDWLRQRIWKHPRWRU
7KHFURZQLVSURSHUO\¿WWHGWRWKHWXEH
7KHHQGOLPLWVRIWKHPRWRUDUHSURSHUO\DGMXVWHG
7KDWWKHVKDGHLVZLWKLQWKHUHFRPPHQGHGZHLJKWOLPLW
The equipment is noisy:
Verify that:
7KHZKHHODQGWKHFURZQDUHZHOODGDSWHGWRWKHXVHGWXEH
7KHPHFKDQLFDOSOD\VEHWZHHQPRWRUDFFHVVRULHVWXEHDQGHQGRIWXEHPXVWEHGH-
creased to the maximum.
7KHZKHHOLVSURSHUO\¿[HGWRWKHWXEH
7KHHTXLSPHQWLVQRWFRQVWUDLQHGEHWZHHQWKHEUDFNHWV
7KHOHQJWKRIWKHQRWFKLVDGDSWHGWRWKHPRWRUKRRNRUWRWKHXVHGFURZQ
'HEULVVFUHZVRURWKHUDUHQRWLQ\RXUWXEH
7KHSRZHUVXSSO\VSHFL¿FDWLRQV
7KHWHPSHUDWXUHRIWKHHQYLURQPHQWLVLQFRQIRUPLW\ZLWKWKHRSHUDWLQJWHPSHUDWXUH

12
Copyright © 2011 Somfy SAS. All rights reserved - V0 - 06/2011
EN
8Technical data
9 Environment
Damaged electric products and batteries should not be disposed of with
normal household waste.
0DNHVXUHWRGURSWKHPLQVSHFLDOO\SURYLGHGFRQWDLQHUVRUDWDQDXWKRUL]HG
organization that will ensure they are recycled
Frequency
Operating temperature
Protection rating
Maximum number of
transmitters
0°C / 60 °C
IP44
12
Power supply 230V/50Hz - 120V/60Hz - 220V/60Hz
433,42MHz
Maximum number of
sensors 3