SOMFY Tilt Only 50 WF RTS Operating instructions

Installation/programming
guide
Interior applications

3
Contents
Overview RTS options 8
Compatibility, Motor-Power supply-sensors 9
Power connections: Applications with RTS integrated motors 11
Basic
Programming and setting of RTS motors 13
1 Connect the RTS transmitter to the motor 13
2 Check the motor rotation direction 13
3 Change motor rotation direction if needed 13
4 Place the blind in the desired UP position 13
5 Set the DOWN position 13
6 Set the UP position 14
7 Confirm end limit setting 14
8 Recording an RTS transmitter 14
Adjustments 15
Adjusting the DOWN limit 15
Adjusting the UP limit 15
Set blind mode: Roller or Venetian 16
Setting My position for NON TILT products 17
Setting My position for TILT products 17
Remove programmed My position 17
Wired RTS receivers, 24 VDC 18
24 V RTS Receivers, setting and programming 18
Setting from the RTS receiver 19
1 Set the RTS receiver in programming mode 19
2 Record the first RTS transmitter 19
Power 4 x 2,5 DC RTS 19
Setting from the RTS remote control 20
Set type of blind: Roll up or Tilt and li 21
Change the motor rotation direction 22
Sett the time for open and close movement 23
Modify the MY position, in Tilt & li mode 26
Modify the MY position, in Roll up mode 27
Remove a programmed MY-position 27
Activating the motor Run timer 28
Add a transmitter 29
Remove an assigned transmitter 29

4
Add or remove transmitters 30
Factory reset 31
Program individual channels to group channel 32
Sonesse 40 WT, Setting of end limits 33
Curtain track 34
Recommendations 34
Motor cable output options 34
Attach motor to rail 34
Wiring guide DCT & RTS 34
Curtain track motors RTS, Programming instruction 35
Connect the RTS transmitter to the motor 35
Check the motor rotation direction 35
Change if needed motor rotation direction 35
Record a RTS transmitter 35
Setting My position 36
Re-adjustment of end -limits 36
Set Touch motion or manual over ride mode 37
Set track speed, default speed = 20 cm/s 38
Add transmitter 39
Reset motor to factory mode, erase all settings 39
Curtain track DCT motors, Wiring control unit to Glydea DCT 40
Glydea DCT, Programming instruction 40
Modify motor rotation direction, if needed 40
Re-adjustment of end -limits 40
Set Touch motion or manual over ride mode 41
Reset motor to factory mode, erase all settings 41
Curtain track WT motors, Wiring instruction 42
Programming instruction 42
Modify motor rotation direction, if needed 42
Back release setting 43
Reset motor to factory mode, erase all settings 43
Advanced
Sun sensor functions 44
Deactivate and activate privacy function 44
Program sun disappearing position 45
Set the motor speed 45

5
Set the tilt speed / scroll wheel step 46
Modify motor rotation direction 47
Modify scroll wheel rotation direction 47
Li-Ion motors 49
Activate/Deactivate RTS 49
Temporary sleeping mode 50
How to replace battery 51
Sonesse 30 DCT 52
Wiring 52
Setting type of blind 52
Setting of rolling speed 52
Setting of tilt speed 53
Reset motor in Factory mode 53
24 V Wired controls for Roll up application 54
Setting of My positions 54
24V Wired control for Tilt & Li applications 55
Adjust tilt speed 55
Set automatic Slat tilting 55
Set My position - from UP end limit 55
Sunis RTS, Adding and setting 56
Connect sun sensor 57
Check Sun mode ON or OFF 58
Check and installation 59
Set the Demo mode ON 59
Switch the Demo mode OFF 60
Explanations of LED signals 61
Is the Sunis Sensor RTS in DEMO-Mode? 61
Thermosunis Indoor Wirefree RTS, Adding and setting 62
Thermosunis Indoor Wirefree RTS 63
Connect sun sensor 63
Mounting of Thermosunis Indoor Wire free RTS 64
Usage options for Thermosunis Indoor Wirefree RTS 64
Get started with Thermosunis Indoor Wire free RTS 65
Activate the sensor 66
Erase the sensor from the motor 67
Setting of the sensitivity (threshold values) 68
DEMO mode 69

6
Sunis WireFree II io sensor 70
Description 70
Program the sensor on a motor with a 1-way transmitter 71
Programming Moco DCE 73
To change to Li application 73
Setting of end limits 74
TaHoma 75
Composition 75
Connect the box 75
Create your account 75
Configure your connected home 76
Add devices 76
Connexoon Window RTS 77
Product components 77
To add products (without Internet connection) 77
Select one of the 6 channels 78
To register the Connexoon 79

7

8
Overview RTS options
Roller blinds Venetian blinds
Pleated - Duette blinds
CurtainsRoman blinds
- +
nMotor LW 25
nDC RTS Receiver
nTilt Only 50
WF RTS
nSonesse ULTRA 30 WF
RTS LI-Ion
nSonesse ULTRA 30 WF
RTS LI-Ion
nSonesse ULTRA 30 WF
RTS LI-Ion
nMotor LW 25
nMotor LV 25
nTransformer
e.g.
Power 2,7DC
nIntegrated DC
RTS receiver
nTransformer
e.g.
Power 2,7DC
nTransformer
e.g.
Power 2,7DC
n Centralis
Indoor
RTS
nReceiver
Centralis
indoor
RTS Drape
nReceiver
Centralis
indoor
RTS Drape
nMotor LW 25
nDC RTS Receiver
nJr Roll Up 30 WF RTS,
Roll up 28 WF RTS,
Jr Roll up 30 WF RTS Li-Ion,
Roll up 24 WF RTS Li-Ion,
Roll up 28 WF RTS Li-Ion,
Sonesse 28 WF RTS Li-Ion,
Sonesse ULTRA 30 WF RTS
Li-Ion
nRoll up 28 WT
nMotor
Sonesse 40 RTS
nMotor
Sonesse 40 io
nMotor
Sonesse
40 io
nMotor
Sonesse 40 io
nDC RTS Receiver
nTransformer
e.g. Power
2,7DC
nTransformer
e.g.
Power 2,7DC
nTransformer
e.g.
Power 2,7DC nTransformer
e.g.
Power 2,7DC
nMotor Sonesse
30 RTS
nMotor Sonesse
30 RTS
nMotor
Sonesse 40 RTS
nMotor
Sonesse 40
nMotor
Sonesse 40
nMotor Sonesse
30 RTS
nMotor
Sonesse 40 RTS
nMotor
Sonesse 40 PA
nMotor Sonesse
(ULTRA) 50
nMotor Sonesse
(ULTRA) 50
nGlydea ULTRA
RTS + track
nIrismo
WireFree
45 RTS
nMovelite
35 RTS
nSolar pack
nSolar pack
nSolar pack
nSolarpack
WireFree range
RTS motorer
24 Volt 230 Volt
RTS Receiver RTS motor RTS Receiver RTS motor io motor
nBattery pack,
rechargeable Li-Ion,
standard AA batteries or
Power supply
nBattery pack,
rechargeable Li-Ion,
standard AA batteries or
Power supply
nBattery pack,
rechargeable Li-Ion,
standard AA batteries or
Power supply
nBattery pack,
rechargeable Li-Ion,
standard AA batteries or
Power supply
nTilt & li 25 WF RTS
n Tilt & Li 25 WF RTS
n Tilt & Li 25 WF RTS

9
Compatibility chart
Compatibility chart, Motor / Remote-sensors
DC Power supply range - Motor compatibility
LV25 B44 LW25 B44 LV25 B64 LW25 B83 LW25 E83 Roll up 28 WT Sonesse 30 RTS Sonesse 30 DCT Sonesse 30 RS 485 Jr Roll Up 30 WF RTS/ Roll Up 28 WF RTS Tilt & Li 25 WF RTS Tilt Only 50 WF RTS
Power 1,1 DC 2 2 1 NC 2 NC NC NC NC NC NC
Power 1,5DC 8 5 4 NC 3 2 2 2 NC NC NC
Power 2,7DC 8 5 4 NC 5 2 2 2 NC NC NC
Animeo DC Power 4,5 11 10 7 NC 7 5 4 4 NC NC NC
Battery tube 8xAA
Lithium/Alkaline NC NC NC NC NC NC NC NC 1 1 1
Rechargeable Li-Ion
battery NC NC NC NC NC NC NC NC 1 1 1
Power supply 12VDC NC NC NC NC NC NC NC NC 1 1 1
DC Motor Power supply with integrated controls - Motor compatibility range
LV25 B44 LW25 B44 LV25 B64 LW25 B83 LW25 E83 Roll up 28 WT Sonesse 30 RTS Sonesse 30 DCT Sonesse 30 RS 485 Jr Roll Up 30 WF RTS/0Roll Up 28 WF RTS Tilt & Li 25 WF RTS Tilt Only 50 WF RTS
Power 1 x 2,5DC RTS 6 5 4 NC 5 NC NC NC NC NC NC
Power 4 x 2,5 DC RTS 4x6 4x5 4x4 NC 4x5 NC NC NC NC NC NC
Inis DC 2 1 1 NC 1 NC NC NC NC NC NC
Moco 4 DC/DCE 4x1 4x1 4x1 4x1 4x1 (DC) NC NC NC NC NC NC
DC Motor controls - Motor compatibility range
(Integrated) DC RTS Rec 2 2 2 NC 2 NC NC NC NC NC NC
Centralis DC IB 2 2 2 NC 2 NC NC NC NC NC NC
Moco 4 DC 4x1 4x1 4x1 NC 4x1 NC NC NC NC NC NC
Sensor/remote controls - Motor/receiver compatibility chart
JrJ3 Roll up 30 WF RTS Jr Roll up 30 WF RTS Li-Ion All other WireFree motors* Sonesse 30 RTS Sonesse 40 RTS Sonesse 50 RTS Glydea/Irismo/ movelite RTS Power 1 x 2,5DC RTS Power 4 x 2,5 DC RTS (Integrated) DC RTS Rec
Telis Range C C C C C C C C C
Telis Modulis Range NC C C C C C C C C
Sunis RTS NC NC C C C NC C C C
Soliris Sensor RTS NC NC C C C NC C C C
Thermosunis/Sunis
Indoor RTS CCCCCCCCC
Chronis RTS Range C C C C C C C C C
Tahoma CCCCCCCCC
Conexxoon RTS C C C C C C C C C
*= Roll up 24 WF RTS Li-ion, Roll up 28 WF RTS Li-Ion, Sonesse 28 WF RTS Li-Ion, Roll Up 28 WF RTS ,
Sonessen ULTRA 30 WF RTS Li-Ion, Tilt&Li 25 WF RTS, Tilt Only 50 WF RTS
C = Compatible
NC = Non compatible
Figure = number of motors possible to connect

10
Compatibility chart
Compatibility chart, Motor / Remote-sensors
io Remote control compatibility chart
Smoove
origin io Smoove 1 io Smoove A/M io Situo 1&5 io Chronis 1&5 io Nina io Nina Timer io
Sonesse 40 io C C C C C C C
io sensor and system compatibility chart
Sunis WF io Tahoma Connexoon Sset & Go EMS2
Sonesse 40 io C C C C C
C = Compatible
NC = Non compatible
Figure = number of motors possible to connect

11
Wirefree motors, external power
Jr 30 Roll Up 30782 WF RTS
Roll Up 28 WF RTS
Tilt & Li 25 WF RTS
Tilt Only 50 WF RTS
Power connections: Motors with integrated Radio receiver
Power and charging connection
Wirefree motors, built in battery
Jr Roll Up 30 WF RTS Li-Ion
Roll Up 24 WF RTS Li-Ion
Sonesse 28 WF RTS Li-Ion
Sonesse ULTRA 30 WF RTS Li-Ion
OR
24 V DC motors
Sonesse 30 RTS
+
-

12
Power connection
IWC Li-Ion motors feedback explanation
230 V AC motors:
Sonesse 40 RTS/io, 2 wires,
Sonesse (ULTRA) 50 RTS
For a motor that is in sleep mode, or with RTS Deactivated
1. Neutral 2. Phase 3. Ground
230V/50 Hz Sonesse 40 RTS Blue Black
230V/50 Hz Sonesse 50 RTS Blue Black Yellow/green
1
2
3 x 1,5 mm23 x 0,75 mm2
3
1
2
3
When connected to charger, or when the programming button on the head is pressed briefly, the motor
reacts with a number of up/down movements. The number tells the motors programmed status
If the motor moves up/down...
For Deactivating / Activating RTS, see page 49
3 times =
the motor is not programmed
2 times =
the motors is programmed, but
no control point is assigned
1 times =
the motor is programmed and
assigned to a remote control.

13
Complete range of IWC radio motors
IWC RTS & io motors - programming and Basic setting Basic
3 Change motor rotation direction if needed
To set Li-Ion motors
in programming
mode.
NOT OK 3
...motor jogs.
...motor jogs.
Briefly press the motor
head programming button
or plug in the charger.
Press until...
Press simultaneously
until...
OK 4
- Connect the motor that should be programmed to power
- For Li-Ion motors, put the motor in program mode
1 Connect the transmitter to the motor
2 Check the motor rotation direction
2 sec.
The motor jogs 3 times and
LED lights orange, motor is
ready for programming
3x
Initial setup

14
Complete range of IWC radio motors
IWC RTS & io motors - programming and Basic setting Basic
6 Set the DOWN position
7 Confirm end limit setting
8 Recording a transmitter
The motor moves upwards and
stops at the UP position
...motor jogs
...motor jogs
Short simultaneous
press
Press until...
Press the prog button
on the back of the
control until...
2 sec.
4 Place the blind in the desired UP position
5 Set the UP position
Blind goes down Stop at desired
down position
Adjust if neededShort
simultaneous
press

15
1 Adjusting the DOWN limit
1 Adjusting the UP limit
2
2
IWC RTS & io motors - programming and Basic setting Basic
Press simultaneously
until...
Press simultaneously
until...
...motor jogs
...motor jogs
Place the blind in the down position
Place the blind in the up position
Choose a new down position
Choose a new up position
Confirm new down position, press “My”
until motor jogs OK
Confirm new down position, press “My”
until motor jogs OK
5 sec.
5 sec.
2 sec.
2 sec.
Complete range of IWC radio motors

16
IWC RTS & io motors - programming and Basic setting Basic
Set blind mode: Roller or Venetian
1
2 Change the setting
Default setting
Tubular motors = Roller
Tilt & Li 25 WF RTS = Venetian
Place the blind half way down
Press simultaneously
until...
Press simultaneously
until...
...motor jogs ...motor jogs
5 sec.
2 sec.
Roll up 28 WF RTS, Roll up 24 WF RTS Li-Ion, Roll up 28 WF RTS Li-Ion, Sonesse 28 WF RTS Li-Ion,
Sonesse ULTRA 30 WF RTS Li-Ion, Sonesse 30 RTS, Sonesse 40 RTS, Tilt&Li 25 WF RTS

17
IWC RTS & io Motors - programming and Basic setting Basic
Setting My position for products/motors in Non Tilt mode
Setting My position for products/motor in Tilt mode
1 Remove programmed My position
2
Place the blind in the down position
Place the blind in the my position
Place the blind in desired position
My can never be set the same as
up or down position
Press `my` until... ...motor jogs
Tilt up to desired slat angle Confirm the My position, press “My”
until motor jogs OK
Confirm the My position, press “My”
until motor jogs OK
5 sec.
5 sec.
5 sec.
Adjusting My position
Repeat procedure to a
new desired position
Adjusting My position
Repeat procedure to a new desired position
or
or
or
or
Complete range of IWC radio motors

18
DC RTS Receiver
Wiring
24 VDC RTS Receivers Basic
(Integrated) DC RTS Receiver, Power 1 x 2,5 DC RTS, Power 4 x 2,5 RTS DC
Integrated DC RTS Receiver
Power 1 x 2,5 DC RTS (power 4 x 2,5 DC RTS, Power 2,7 DC)
- +
- +
230/24 V power
supply
230/24 V power
supply

19
24 V RTS Receivers - Programming and basic settings Basic
1 Set the RTS receiver in programming mode
2 Record the first RTS transmitter
Setting from the RTS receiver
When programming
a multi channel control,
choose channel first
3 sec.
- +
3 sec.
or or
If the blind doesn’t react,
- reverse the 24V power
supply cables
- try from start again
...motor jogs.
...motor jogs
OK
Press the prog button until...
Press the prog button
on the back of the
control until...
Once output channel is chosen
Output 4= 4 beepOutput 3= 3 beepOutput 2 =
2 beep
Output 1 =
1 beep
Each press
change
channel
Press and release
prog button
quickly
Press and hold to
enter in programming
mode
Select the output channel (Per default output 1 is active)
Power 4 x 2,5 DC RTS
Motor jogs
OK
When in programming mode follow the programming
steps of Power 1 x2,5 DC RTS for each output
channel
(Integrated) DC RTS Receiver, Power 1 x 2,5 DC RTS, Power 4 x 2,5 DC RTS

20
24 V RTS Receivers - Programming and basic settings Basic
(Integrated) DC RTS Receiver, Power 1 x 2,5 DC RTS, Power 4 x 2,5 DC RTS
1 Connect the RTS remote control to the RTS receiver
2 Recording the first RTS transmitter
Setting from the RTS remote control
When programming
a multi channel control,
choose channel first
If the blind doesn’t react,
- reverse the 24V power
supply cables
- try from start again
...motor jogs
OK
...motor jogs
Press the prog button
on the back of the
control until...
Short simultaneous
press