SOMFY Telis Soliris 4 RTS Patio User manual

The Telis Soliris RTS Patio is a hand-held remote to operate awnings, screens and
shutters featuring Radio Technology. It also has the added feature of activating an
RTS sun sensor remotely. The RTS is omni-directional, so there is no need to aim
the remote at the product being controlled.
Telis Soliris 4 RTS Patio
Part Number:
1811243
Introduction - Multi-Channel Remote Control
Up Button
Center “my” Button
Down Button
Programming
Button (PROG)
Wind Only
Sun & Wind
Sun/Wind/Channel
Selector
Telis Soliris 4 RTS Patio with Sun/Wind function
Back
Programming a new remote
1. With the current remote press the Channel Selector Button. Each channel operates a single window
or group of window coverings. LED lights will illuminate, indicating which channel is being operated.
2. Using a paper clip, pen or similar device, press and hold the Programming Button on the back of your
current remote until your window shade moves up and down quickly.
3. On the new remote, select a channel to assign the window covering to. Using a paper clip, pen, or
similar device, press and hold the Programming Button on the back of the new remote. The window
shade will move up and down quickly.
4. The new remote is now programmed to operate your window covering.
Programming and Operating
Continued On Next Page
page 1 of 3
Note: repeat process for the other
window coverings/channels.

Programming Favorite Position with Remote
The remote operates interior and exteriors shading solutions. Each is operated by a channel.
1. Press the Channel Selector Button. The LED lights will illuminate, indicating which channel
is being operated.
2. Use the up ( ) or down ( ) buttons to position the shade in your favorite position.
Use the ( ) button to stop the shade when it reaches that position.
3. Press and hold the center ( ) button until the window moves up and down quickly.
Favorite position is programmed.
4. During normal operation, select the window covering to operate using the channel selector button
then press the ( ) button to place window shade in your favorite position.
Activating Sun/Wind controls (which requires optional sun/wind sensor).
• The wind sensor is factory set and does not require programming. In order to use Sun/Wind mode,
each window covering must be assigned a channel and be paired with the Sun/Wind mode.
1. Using the channel selector button, select the interior or exterior shading solution you wish to
operate with the Sun/Wind sensor.
2. Using a paper clip, pen or similar device, press and hold the Programming Button (PROG) on the back
of the remote until the interior or exterior shading solution briefly moves up and down.
3. Press and hold the SUN/WIND SELECTOR BUTTON until all LED lights activate.
The lights will change sides and the interior or exterior shading solution will briefly move up
and down. When the left side is lit, the interior or exterior shading solution will only react to wind
levels. When the right side is lit, the interior or exterior shading solution will react to both sun and
wind levels.
Operating the Remote
The remote operates interior and exteriors shading solutions. Each is operated by a channel.
1. Press the Channel Selector Button. The LED lights will illuminate, indicating which channel is being
operated.
2. Press the up ( ) button to raise your window covering.
3. Press the down ( ) button to lower your window covering.
4. Press the center ( ) button to stop the window covering during operation.
Programming and Operating Continued
page 2 of 3
Note: repeat process for the other window coverings/channels

This device is FCC certified and complies with part 15 of the FCC rules.
RTS compatibility: RTS transmitters are capable of operating any RTS motor.
page 3 of 3
BATTERY RECYCLING OR DISPOSAL
Discard batteries and electrical components
following local codes or regulations. Recycle
batteries and electrical components with
designated electronic recycle centers.
Battery Installation
Replacing the Battery
1. Using a small screwdriver, loosen the screws on the reverse side of the remote control and
remove the back cover.
2. Replace the battery with one 2430 Lithium 3V battery
Note: Visit https://store.somfysystems.com/ to
purchase an additional or replacement product.